Home › Vehicle Interior › THEFT DETERRENT › THEFT DETERRENT SYSTEM
RM24M0E _58 Vehicle Interior _059585 THEFT DETERRENT _0292193 THEFT DETERRENT SYSTEM G

THEFT DETERRENT  THEFT DETERRENT SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:

Before checking the theft deterrent system function, cancel the smart entry and start system.


PROCEDURE

Hide 1. OUTLINE OF THEFT DETERRENT SYSTEM

a.

When the theft deterrent system detects that the vehicle is being tampered with, the vehicle horns and security horn will sound and hazard warning lights will flash continuously.


b.

The system has modes: active arming mode (refer to "ACTIVE ARMING MODE").


c.

Each mode has 4 states: disarmed state, arming preparation state, armed state and alarm sounding state.

i.

Disarmed state:

·

The alarm function is not operating.

·

The theft deterrent system is not operating.



ii.

Arming preparation state:

The theft deterrent system is not operating.



iii.

Armed state:

The theft deterrent system is operating.



iv.

Alarm sounding state:

The alarm function is operating (30 +-5 seconds).


Refer to table below for alarm method and time:
Alarm Method Hazard Warning Light Blinking (cycle of flasher relay)
Vehicle Horn Sounding (cycle of 0.4 seconds)
Security Horn Sounding (cycle of 0.4 seconds)
Headlight Flashing
Taillight Flashing
Room light Illuminating
Security Indicator Illuminating
Alarm Time 30 +-1.5 seconds

HINT:

If one of the doors is unlocked during the alarm sounding state without using a proper key, a forced door lock signal will be output (refer to "FORCED DOOR LOCK CONTROL").




Hide 2. ACTIVE ARMING MODE

HINT:
·

Active arming mode starts the alarm control immediately after the doors are locked.

·

Before checking the theft deterrent system, cancel the smart entry and start system.



System state State switching condition Switches to
1. Disarmed state
1.

With all doors and engine hood closed, lock all doors by wireless operation.

2.

With all doors and engine hood closed, lock all doors using mechanical key.

3.

With any door or the engine hood open, lock all doors and close all doors and engine hood.


2. Arming preparation state
2. Arming preparation state
1.

Unlock all doors by wireless operation.

2.

Unlock all doors using mechanical key.

3.

Unlock a door.

4.

Open engine hood.

5.

With brake pedal depressed, hold key 10 mm (0.4 in.) from engine switch with key ornament facing engine switch for 5 seconds, and turn ignition switch on (ACC or IG).

6.

Reconnect battery.


1. Disarmed state
1.

Allow 30 (+-1.5) seconds to elapse.


3. Armed state
3. Armed State
1.

Unlock all doors by wireless operation.

2.

Unlock all doors using mechanical key.

3.

Depress brake pedal, hold key 10 mm (0.4 in.) from engine switch with key ornament facing engine switch for 5 seconds, and turn ignition switch on (IG).


1. Disarmed state
1.

Open engine hood.

2.

Open a door.

3.

Unlock a door without using wireless operation.

4.

Unlock a door without using mechanical key.

5.

Disconnect and reconnect battery negative (-) cable.

6.

Force engine ignition system to turn on without proper engine start method.


4. Alarm sounding state
4. Alarm sounding state
1.

Unlock all doors by wireless operation.

2.

Unlock all doors using mechanical key.

3.

Depress brake pedal, hold key 10 mm (0.4 in.) from engine switch with key ornament facing engine switch for 5 seconds, and turn ignition switch on (IG).


1. Disarmed state
1.

Allow 30 (+-5) seconds to elapse.


3. Armed state (alarm stops sounding)

Hide 3. FORCED DOOR LOCK CONTROL

a.

The forced door lock control also helps to prevent the vehicle from being tampered with. When a door is unlocked and the alarm starts, the door is forced to lock by a forced door lock signal.

i.

Conditions that force the doors to lock:

·

0.4 seconds have elapsed after the previous output of a forced door lock signal.

·

The theft deterrent system is in the alarm sounding state of active arming mode.

·

A door is unlocked.




Hide 4. SECURITY INDICATOR OUTPUT

a.

The security indicator turns on and off based on output signals from the main body ECU. However, in some cases, the actual status of the security indicator is different from the output signals of the main body ECU.

Output:
State of Theft Deterrent System Security Indicator
Output Signals from Certification ECU Actual Lighting Condition
Disarmed state OFF OFF (Immobiliser system not set)
BLINKING (Immobiliser system set)
Arming preparation state ON ON
Armed state OFF BLINKING
Alarm sounding state ON ON

Blinking cycle:
Time Security Indicator
0.2 seconds ON
1.8 seconds OFF

HINT:

When the immobiliser system is set, the security indicator blinks during the disarmed state and the armed state due to the output signals from the immobiliser system.