Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Operating Light Control Rheostat does not Change Light Brightness  


DESCRIPTION

The combination meter assembly controls the combination meter illumination in accordance with the light control signal from the light control rheostat on the trip switch.

WIRING DIAGRAM

E133446E02
5.532,2.478 5.864,2.623 0.332,0.145 10 G28 5.55,1.123 5.980,1.269 0.429,0.145 10 TC O 3.393,1.021 3.822,1.166 0.429,0.145 10 4*1 3.393,1.226 3.822,1.372 0.429,0.145 10 2*2 3.033,1.226 3.300,1.372 0.267,0.145 10 TC 1.49,1.021 1.827,1.166 0.336,0.145 10 6*1 1.413,1.226 1.842,1.372 0.429,0.145 10 10*2 1.982,1.226 2.412,1.372 0.429,0.145 10 E 0.053,3.287 0.867,3.432 0.813,0.145 10 *1: for LHD 0.053,3.536 0.867,3.681 0.813,0.145 10 *2: for RHD 1.917,1.596 3.457,1.742 1.540,0.145 10 G46 1.917,1.736 3.457,1.882 1.540,0.145 10 Trip Switch 1.917,1.876 3.457,2.022 1.540,0.145 10 (Light Control Rheostat) 5.233,1.226 5.421,1.372 0.188,0.145 10 35 5.532,2.622 6.794,2.767 1.262,0.145 10 Combination Meter

PROCEDURE

1.READ VALUE USING DATA LIST (LIGHT CONTROL RHEOSTAT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and the tester ON.


c.

Read the Data List according to the prompts displayed on the tester.

Combination meter
Item Measurement Item / Range (Display) Normal Condition Diagnostic Note
Light Control Switch Light control rheostat switch signal / ON or OFF ON: Rheostat switch pushed
OFF: Rheostat switch not pushed
-

OK:

ON is displayed on the intelligent tester screen when switch is pressed.




NG

2.INSPECT TRIP SWITCH (LIGHT CONTROL RHEOSTAT)

OK

REPLACE COMBINATION METER ASSEMBLY

2.INSPECT TRIP SWITCH (LIGHT CONTROL RHEOSTAT)
a.
E127509E28
0.792,1.073 1.333,1.073 1.333,1.073 1.531,1.25 false 2.094,1.552 2.635,1.552 false 2.583,1.083 2.042,1.083 2.042,1.083 1.875,1.292 false 0.792,1.563 1.333,1.563 false 0.49,1.479 0.74,1.635 0.25,0.156 10 false E*2 2.719,1.469 2.969,1.625 0.25,0.156 10 false E*1 0.406,1.865 1.958,2.021 1.552,0.156 10 false *1: for LHD 1.333,1.865 2.885,2.021 1.552,0.156 10 false *2: for RHD 0.396,0.99 0.75,1.146 0.354,0.156 10 false TC*1 2.646,1.01 2.99,1.167 0.344,0.156 10 false TC*2

Remove the trip switch.


b.

Measure the resistance of the switch.

Standard resistance:
for LHD
Tester Connection Switch Condition Specified Condition
4 (TC) - 6 (E) Rheostat switch pushed Below 1 Ω
4 (TC) - 6 (E) Rheostat switch not pushed 10 kΩ or higher

for RHD
Tester Connection Switch Condition Specified Condition
2 (TC) - 10 (E) Rheostat switch pushed Below 1 Ω
2 (TC) - 10 (E) Rheostat switch not pushed 10 kΩ or higher




OK

3.CHECK WIRE HARNESS (TRIP SWITCH - COMBINATION METER AND BODY GROUND)

NG

REPLACE TRIP SWITCH

3.CHECK WIRE HARNESS (TRIP SWITCH - COMBINATION METER AND BODY GROUND)
a.
E358403E01
0.75,0.542 1.167,0.792 0.417,0.25 0.667,2.5 1.083,2.75 0.417,0.25 1.865,1.385 1.979,1.167 1.979,1.167 2.344,1.167 false 1.604,1.396 1.438,1.177 1.438,1.177 1.135,1.177 false 1.094,1.635 1.438,1.635 false 2.021,1.615 2.385,1.615 false 2.26,4.01 2.26,3.5 false 0.094,0.083 1.656,0.385 1.563,0.302 10 false Wire Harness Side: 0.823,0.583 1.323,0.823 0.5,0.24 10 false G46 1.375,0.563 2.26,0.802 0.885,0.24 10 false Trip Switch 2.406,1.083 2.906,1.323 0.5,0.24 10 false TC*1 2.448,1.531 2.948,1.771 0.5,0.24 10 false E*2 0.771,1.094 1.271,1.333 0.5,0.24 10 false TC*2 0.813,1.552 1.313,1.792 0.5,0.24 10 false E*1 0.74,2.531 1.24,2.771 0.5,0.24 10 false G28 1.188,2.521 2.563,2.813 1.375,0.292 10 false Combination Meter 2.104,4.031 2.604,4.271 0.5,0.24 10 false TC O 0.135,4.052 1.229,4.292 1.094,0.24 10 false *1: for LHD 0.135,4.302 1.229,4.542 1.094,0.24 10 false *2: for RHD

Disconnect the G46 switch connector.


b.

Disconnect the G28 meter connector


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LHD
Tester Connection Specified Condition
G46-4 (TC) - G28-35 (TC O) Below 1 Ω
G46-4 (TC) or G28-35 (TC O) - Body ground 10 kΩ or higher
G46-6 (E) - Body ground Below 1 Ω

for RHD
Tester Connection Specified Condition
G46-2 (TC) - G28-35 (TC O) Below 1 Ω
G46-2 (TC) or G28-35 (TC O) - Body ground 10 kΩ or higher
G46-10 (E) - Body ground Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR