Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Odo/Trip Switch Malfunction  


DESCRIPTION

The meter's ODO / TRIP display changes each time the trip switch is pressed.

HINT:

For more information about changing between displays, refer to the owner's manual.


WIRING DIAGRAM

E133446E01
5.532,2.477 5.864,2.623 0.332,0.145 10 G28 5.55,1.123 5.979,1.269 0.429,0.145 10 ODO 3.393,1.02 3.822,1.166 0.429,0.145 10 5*1 3.393,1.226 3.822,1.371 0.429,0.145 10 1*2 3.141,1.226 3.301,1.371 0.161,0.145 10 + 1.49,1.02 1.826,1.166 0.336,0.145 10 6*1 1.413,1.226 1.842,1.371 0.429,0.145 10 10*2 1.982,1.226 2.411,1.371 0.429,0.145 10 E 0.04,3.245 0.797,3.390 0.758,0.145 10 *1: for LHD 0.04,3.528 0.797,3.673 0.758,0.145 10 *2: for RHD 1.917,1.596 3.457,1.741 1.540,0.145 10 G46 1.917,1.736 3.457,1.882 1.540,0.145 10 Trip Switch 1.917,1.876 3.457,2.022 1.540,0.145 10 (ODO / TRIP Switch) 5.233,1.226 5.421,1.371 0.188,0.145 10 34 5.532,2.622 6.794,2.767 1.262,0.145 10 Combination Meter

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ODO/TRIP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and the tester ON.


c.

Read the Data List according to the prompts displayed on the tester.

Combination meter
Item Measurement Item / Range (Display) Normal Condition Diagnostic Note
ODO/TRIP Change SW ODO / TRIP change switch signal / ON or OFF ON: ODO / TRIP change switch pushed
OFF: ODO / TRIP change switch not pushed
-

OK:

ON is displayed on the intelligent tester screen when switch is pressed.




NG

2.INSPECT TRIP SWITCH (ODO / TRIP SWITCH)

OK

REPLACE COMBINATION METER ASSEMBLY

2.INSPECT TRIP SWITCH (ODO / TRIP SWITCH)
a.
E127509E22
0.833,1.333 1.365,1.333 false 0.833,1.563 1.365,1.563 false 2.073,1.333 2.615,1.333 false 2.073,1.573 2.615,1.573 false 2.688,1.49 2.938,1.646 0.25,0.156 10 false E*1 0.542,1.479 0.792,1.635 0.25,0.156 10 false E*2 0.26,1.865 1.813,2.021 1.552,0.156 10 false *1: for LHD 1.104,1.875 2.656,2.031 1.552,0.156 10 false *2: for RHD 0.552,1.219 0.854,1.417 0.302,0.198 10 false +*1 2.677,1.229 2.927,1.385 0.25,0.156 10 false +*2

Remove the trip switch.


b.

Measure the resistance of the switch.

Standard resistance:
for LHD
Tester Connection Switch Condition Specified Condition
5 (+) - 6 (E) ODO / TRIP switch pushed Below 1 Ω
5 (+) - 6 (E) ODO / TRIP switch not pushed 10 kΩ or higher

for RHD
Tester Connection Switch Condition Specified Condition
1 (+) - 10 (E) ODO / TRIP switch pushed Below 1 Ω
1 (+) - 10 (E) ODO / TRIP switch not pushed 10 kΩ or higher




OK

3.CHECK WIRE HARNESS (TRIP SWITCH - COMBINATION METER AND BODY GROUND)

NG

REPLACE TRIP SWITCH

3.CHECK WIRE HARNESS (TRIP SWITCH - COMBINATION METER AND BODY GROUND)
a.
E358403E04
0.75,0.542 1.167,0.792 0.417,0.25 0.667,2.5 1.083,2.75 0.417,0.25 1.094,1.635 1.438,1.635 false 2.021,1.615 2.385,1.615 false 2.156,4.042 2.156,3.531 false 1.083,1.417 1.427,1.417 false 2,1.417 2.365,1.417 false 0.094,0.083 1.656,0.385 1.563,0.302 10 false Wire Harness Side: 0.823,0.583 1.323,0.823 0.5,0.24 10 false G46 1.375,0.563 2.26,0.802 0.885,0.24 10 false Trip Switch 2.417,1.313 2.917,1.552 0.5,0.24 10 false +*1 2.448,1.531 2.948,1.771 0.5,0.24 10 false E*2 0.802,1.323 1.302,1.563 0.5,0.24 10 false +*2 0.813,1.573 1.313,1.813 0.5,0.24 10 false E*1 0.74,2.531 1.24,2.771 0.5,0.24 10 false G28 1.188,2.521 2.563,2.813 1.375,0.292 10 false Combination Meter 2.01,4.052 2.51,4.292 0.5,0.24 10 false ODO 0.135,4.052 1.229,4.292 1.094,0.24 10 false *1: for LHD 0.135,4.302 1.229,4.542 1.094,0.24 10 false *2: for RHD

Disconnect the G46 switch connector.


b.

Disconnect the G28 meter connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LHD
Tester Connection Specified Condition
G46-5 (+) - G28-34 (ODO) Below 1 Ω
G46-5 (+) or G28-34 (ODO) - Body ground 10 kΩ or higher
G46-6 (E) - Body ground Below 1 Ω

for RHD
Tester Connection Specified Condition
G46-1 (+) - G28-34 (ODO) Below 1 Ω
G46-1 (+) or G28-34 (ODO) - Body ground 10 kΩ or higher
G46-10 (E) - Body ground Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR