Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM D

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.
B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

Data of the system can be read through the Data Link Connector 3 (DLC3) of the vehicle. Therefore, when the system seems to be malfunctioning, use the intelligent tester to check for a malfunction and repair it.



CHECK DLC3


a.
H100769E31
2.334,0.191 2.786,0.367 0.452,0.176 10 CANH 0.886,0.191 1.178,0.367 0.293,0.176 10 CG 1.59,1.794 2.018,1.970 0.428,0.176 10 CANL 2.335,1.794 2.628,1.970 0.293,0.176 10 BAT 1.966,1.422 1.878,1.755 false 2.33,1.424 2.452,1.767 false 1.574,0.886 1.128,0.377 false 1.965,0.878 2.347,0.375 false 1.611,0.148 1.904,0.324 0.293,0.176 10 SG 1.763,0.345 1.779,0.884 false 2.866,1.123 3.159,1.299 0.293,0.176 10 SIL 2.139,1.007 2.83,1.193 false

The vehicle uses the ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with ISO 15031-03 and matches the ISO 15765-4 format.

Symbols (Terminal No.) Terminal Description Condition Specified Condition
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off* 54 to 69 Ω
CANH (6) - Battery positive HIGH-level CAN bus line Ignition switch off* 6 kΩ or higher
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off* 200 Ω or higher
CANL (14) - Battery positive LOW-level CAN bus line Ignition switch off* 6 kΩ or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off* 200 Ω or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.


If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.


HINT:

Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

·

If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.

·

If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.