Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM G

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK SPEEDOMETER

a.

Check the operation.

i.

Using a speedometer tester, check that the speedometer reading is within the allowable range shown in the table below. Also, check for proper operation of the odometer.

Reference km/h (for 2GR-FE RHD or 2AZ-FE RHD without Entry Function)
GTS Indication Acceptable Range
20 km/h 20.3 to 25.6 km/h
40 km/h 40.6 to 45.4 km/h
60 km/h 61.0 to 65.9 km/h
80 km/h 81.3 to 86.3 km/h
100 km/h 101.6 to 106.5 km/h
120 km/h 121.9 to 127.1 km/h
140 km/h 142.2 to 147.4 km/h
160 km/h 162.6 to 168.3 km/h

Reference km/h (except 2GR-FE RHD or 2AZ-FE RHD without Entry Function)
GTS Indication Acceptable Range
20 km/h 21.0 to 25.0 km/h
40 km/h 41.7 to 46.2 km/h
60 km/h 62.7 to 67.2 km/h
80 km/h 83.4 to 88.4 km/h
100 km/h 104.3 to 109.3 km/h
120 km/h 125.1 to 130.6 km/h
140 km/h 145.8 to 151.8 km/h
160 km/h 166.2 to 173.2 km/h

CAUTION:

Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.



ii.

Check the deflection width of the speedometer indicator.

Reference:

Width 0.3°




Hide 2.CHECK OUTPUT SIGNAL OF VEHICLE SPEED SENSOR

a.
E358381E01
0.167,0.5 0.583,0.75 0.417,0.25 0.823,1.427 0.823,0.896 false 0.229,0.531 0.688,0.76 0.458,0.229 10 false G28 0.625,1.458 1.208,1.677 0.583,0.219 10 false 40 (+S) 0.438,2.323 1.25,2.542 0.813,0.219 10 false Waveform 2.802,3.75 3.26,3.979 0.458,0.229 10 false GND

Check the output signal waveform.

i.

Remove the combination meter sub-assembly, but do not disconnect the connector.


ii.

Connect an oscilloscope to terminal G28-40 and the body ground.


iii.

Start the engine.


iv.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV, 20 ms/DIV
Vehicle condition Driving at approx. 20 km/h

OK:

Waveform is as shown in the illustration.


HINT:

As the vehicle speed increases, the cycle of the signal waveform narrows.




Hide 3.CHECK TACHOMETER (w/o Multi-information Display)

a.

Check the operation.

i.

Connect the tune-up test tachometer, and start the engine.

CAUTION:
·

Reversing the connection of the tachometer will damage the transistors and the insides of the diodes.

·

When removing or installing the tachometer, be careful not to drop or strike it.




ii.

Compare the result of the test with the standard indication.

Reference
GTS Indication Acceptable Range
700 rpm 630 to 770 rpm
1000 rpm 900 to 1100 rpm
2000 rpm 1850 to 2150 rpm
3000 rpm 2800 to 3200 rpm
4000 rpm 3800 to 4200 rpm
5000 rpm 4800 to 5200 rpm
6000 rpm 5750 to 6250 rpm



Hide 4.CHECK FUEL RECEIVER GAUGE

a.
I030899

Disconnect the connector from the fuel sender gauge assembly.


b.

Turn the engine switch on (IG), then check the position of the fuel receiver gauge needle.

OK:

Needle position is on EMPTY.



c.

Connect terminals 2 and 3 on the wire harness side connector of the fuel sender gauge assembly.


d.

Turn the engine switch on (IG), then check the position of the fuel receiver gauge needle.

OK:

Needle position is on FULL.



Hide 5.CHECK FUEL LEVEL WARNING LIGHT

a.

Disconnect the connector from the fuel sender gauge assembly.


b.

Turn the engine switch on (IG), check that the fuel receiver gauge needle indicates EMPTY and fuel level warning light comes on.

OK:

Fuel level warning light comes on.



Hide 6.CHECK BRAKE WARNING LIGHT

a.

Inspect the brake warning light.

i.

Disconnect the connector from the parking brake switch.


ii.

Turn the engine switch on (IG).


iii.

Ground the terminal of the wire harness side connector, and then check that the brake warning light illuminates.

OK:

Brake warning light illuminates.




Hide 7.CHECK ENGINE OIL PRESSURE WARNING

a.

w/o Multi-information Display

i.

Disconnect the connector from the engine oil pressure switch assembly.


ii.

Turn the engine switch on (IG).


iii.

Ground the terminal of the wire harness side connector, then check the engine oil pressure warning light.

OK:

Engine oil pressure warning light comes on.




b.

w/ Multi-information Display

i.

Disconnect the connector from the engine oil pressure switch assembly.


ii.

Turn the engine switch on (IG).


iii.

Ground the terminal of the wire harness side connector, then check the displayed on multi-information display.

OK:

"Low Oil Pressure Stop in a Safe Place See Owner`s Manual" displayed on multi-information display.