Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The combination meter assembly controls the fuel receiver gauge in accordance with the resistance of the fuel sender gauge, which varies depending on the amount of fuel remaining in the fuel tank.

WIRING DIAGRAM

E358401E01
2.469,1.292 2.781,1.49 0.313,0.198 10 false 1 2.469,1.938 2.781,2.135 0.313,0.198 10 false 2 4.677,1.271 4.99,1.469 0.313,0.198 10 false 27 4.667,1.927 4.979,2.125 0.313,0.198 10 false 30 4.969,1.813 5.281,2.01 0.313,0.198 10 false FE 4.979,1.146 5.292,1.344 0.313,0.198 10 false L 5.167,2.604 5.479,2.802 0.313,0.198 10 false G28 5.167,2.76 6.573,3.063 1.406,0.302 10 false Combination Meter 0.927,2.625 1.24,2.823 0.313,0.198 10 false M17 0.927,2.781 2.406,3.135 1.479,0.354 10 false Fuel Sender Gauge

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL GAUGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Perform the Active Test according to the prompts displayed on the tester.

Combination meter
Item Test Details Diagnostic Note
Fuel Meter Operation EMPTY / 1/2 / FULL Value selected during Active Test is displayed

OK:

Value selected during Active Test is displayed.




OK

2.READ VALUE USING DATA LIST (FUEL SIGNAL)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING DATA LIST (FUEL SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and the tester ON.


c.

Read the Data List according to the prompts displayed on the tester.

Combination meter
Item Measurement Item / Range (Display) Normal Condition Diagnostic Note
Fuel Input Fuel input signal / Min.: 0, Max.: 127.5 Fuel gauge indicates (F): 58.5
Fuel gauge indicates (1/2): 32.5
Fuel gauge indicates (E): 6.5
-

OK:

Meter / gauge value and tester value are the same.




OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
E134168E01
1.825,1.992 2.154,2.142 0.330,0.150 10 F 5.734,1.46 6.296,1.610 0.562,0.150 10 45.4 mm 6.14,1.978 6.722,2.128 0.582,0.150 10 (0.87 in.) 5.818,2.39 7.130,2.540 1.312,0.150 10 Standard of Sender 5.734,1.621 6.396,1.771 0.663,0.150 10 (1.79 in.) 6.14,1.816 6.726,1.966 0.586,0.150 10 22.1 mm 6.546,3.242 7.140,3.392 0.593,0.150 10 77.3 mm 6.546,3.41 7.159,3.560 0.613,0.150 10 (3.04 in.) 1.825,2.693 2.154,2.843 0.330,0.150 10 1/2 1.825,3.309 2.154,3.459 0.330,0.150 10 E 4.539,2.202 5.278,1.53 5.278,1.53 5.699,1.53 false 4.931,2.552 5.671,1.88 5.671,1.88 6.091,1.88 false 5.351,2.802 6.091,3.306 6.091,3.306 6.511,3.306 false

a.

Remove the fuel sender gauge.


b.

Measure the resistance of the gauge.

Standard resistance:
Tester Connection Float Level Specified Condition
1 - 2 F 15.0 +-1.5 Ω
1 - 2 1/2 212.5 +-12.2 Ω
1 - 2 E 410.0 +-4.5 Ω




OK

4.CHECK WIRE HARNESS (COMBINATION METER - FUEL SENDER GAUGE)

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

4.CHECK WIRE HARNESS (COMBINATION METER - FUEL SENDER GAUGE)
a.
E358402E01
0.667,0.583 1.083,0.833 0.417,0.25 0.583,2.833 1,3.083 0.417,0.25 1.271,2.25 1.271,1.75 false 1.635,2.26 1.635,1.76 false 0.094,0.073 1.635,0.417 1.542,0.344 10 false Wire Harness Side: 0.74,0.625 1.333,0.917 0.594,0.292 10 false G28 1.219,0.615 2.604,0.938 1.385,0.323 10 false Combination Meter 1.24,2.292 1.833,2.583 0.594,0.292 10 false L 1.563,2.292 2.156,2.583 0.594,0.292 10 false FE 0.656,2.865 1.25,3.156 0.594,0.292 10 false M17 1.115,2.854 2.479,3.177 1.365,0.323 10 false Fuel Sender Gauge

Disconnect the G28 meter connector.


b.

Disconnect the M17 gauge connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G28-27 (L) - M17-1 Below 1 Ω
G28-30 (FE) - M17-2 Below 1 Ω
G28-27 (L) or M17-1 - Body ground 10 kΩ or higher
G28-30 (FE) or M17-2 - Body ground 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR