Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Receiver Gauge Malfunction  


DESCRIPTION

The combination meter assembly receives the engine coolant temperature sensor signal from the ECM and displays it using CAN communication.

WIRING DIAGRAM

E358399E01
1.896,1.073 2.448,1.281 0.552,0.208 10 false CANH 1.906,1.719 2.458,1.927 0.552,0.208 10 false CANL 2.427,1.188 2.979,1.396 0.552,0.208 10 false 41 2.438,1.854 2.99,2.063 0.552,0.208 10 false 49 3.26,1.188 4.052,1.406 0.792,0.219 10 false CAN Line 4.615,1.177 5.167,1.385 0.552,0.208 10 false 32 4.615,1.844 5.167,2.052 0.552,0.208 10 false 31 5.135,2.542 5.688,2.75 0.552,0.208 10 false G28 5.135,2.719 6.635,3.021 1.5,0.302 10 false Combination Meter 1.115,2.531 1.667,2.74 0.552,0.208 10 false A7 1.104,2.708 1.656,2.917 0.552,0.208 10 false ECM 4.927,1.063 5.479,1.271 0.552,0.208 10 false CANH 4.927,1.729 5.479,1.938 0.552,0.208 10 false CANL 3.302,1.844 4.094,2.063 0.792,0.219 10 false CAN Line

CAUTION / NOTICE / HINT

HINT:
·

If DTC U0100 has been stored, troubleshoot the CAN communication system first.

·

If there is an open or short in the engine coolant temperature sensor circuit, an SFI system DTC is output. If output, perform troubleshooting on the SFI system.



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COOLANT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Perform the Active Test according to the prompts displayed on the tester.

Combination meter
Item Test Details Diagnostic Note
Water Temperature Meter Operation LOW / NORMAL / HIGH Value selected during Active Test is displayed

OK:

Value selected during Active Test is displayed.




OK

2.READ VALUE USING DATA LIST (COOLANT TEMPERATURE)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING DATA LIST (COOLANT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and the tester ON.


c.

Read the Data List according to the prompts displayed on the tester.

Combination meter
Item Measurement Item / Range (Display) Normal Condition Diagnostic Note
Coolant Temperature Coolant temperature / Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) After warming up: 80 to 95°C (176 to 203°F) If the value is "0°C (32°F)" or "127.5°C (261.5°F)", sensor circuits are open or shorted.

OK:

Vehicle's coolant temperature and tester value are the same.




OK

GO TO SFI SYSTEM

NG

REPLACE COMBINATION METER ASSEMBLY