Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059588 NAVIGATION / MULTI INFO DISPLAY _0292199 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transfers the switch signals using the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E226159E51
0.823,2.167 1.969,2.542 1.146,0.375 10 false Television Display Assembly 4.969,2.01 5.323,2.156 0.354,0.146 10 false F2 4.958,2.167 6.198,2.708 1.24,0.542 10 false Navigation Receiver Assembly 5.094,1.5 5.583,1.75 0.49,0.25 10 false TX1- 5.094,0.708 5.51,0.885 0.417,0.177 10 false TX1+ 4.844,1.396 5.021,1.542 0.177,0.146 10 false 10 4.885,0.594 4.99,0.771 0.104,0.177 10 false 9 1.813,1.5 2.063,1.646 0.25,0.146 10 false TX- 1.771,0.688 2.052,0.865 0.281,0.177 10 false TX+ 2.188,1.385 2.365,1.531 0.177,0.146 10 false 4 2.167,0.573 2.365,0.75 0.198,0.177 10 false 3 0.823,1.99 1.208,2.198 0.385,0.208 10 false Q21

CAUTION / NOTICE / HINT

NOTICE:

When replacing the navigation receiver assembly, perform vehicle contract setting (See page Audio / Visual / Telematics>G-BOOK>G-BOOK SYSTEM>REGISTRATION).


HINT:

The navigation receiver assembly is the master unit.


PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
U189943E01
0.082,0.042 0.273,0.210 0.192,0.168 10 *a 1.601,0.26 1.804,0.417 0.203,0.157 10 F2 1.262,1.618 1.620,1.787 0.358,0.168 10 TX- 1.85,1.618 2.240,1.787 0.390,0.168 10 TX+ 1.637,1.282 1.464,1.594 false 1.78,1.282 1.974,1.594 false

Disconnect the F2 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-9 (TX+) - F2-10 (TX-) Always 60 to 80 Ω


Text in Illustration
*a Component without harness connected
(Navigation Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the F2 navigation receiver assembly connector.


b.

Disconnect the Q21 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-9 (TX+) - Q21-3 (TX+) Always Below 1 Ω
F2-10 (TX-) - Q21-4 (TX-) Always Below 1 Ω
F2-9 (TX+) - Body ground Always 10 kΩ or higher
F2-10 (TX-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.




OK

REPLACE MALFUNCTIONING PARTS

NG