Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059588 NAVIGATION / MULTI INFO DISPLAY _0292199 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Sound Signal Circuit between Navigation Receiver Assembly and Television Display Assembly  


DESCRIPTION

The television display assembly sends an RSE sound signal to the navigation receiver assembly via the sound signal circuit.

The sound signal that has been sent is amplified by the navigation receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.

WIRING DIAGRAM

E233688E03
0.865,0.74 1.26,0.896 0.396,0.156 10 false SLD9 1.042,1.323 1.26,1.479 0.219,0.156 10 false R+ 1.083,1.938 1.26,2.094 0.177,0.156 10 false R- 1.063,2.521 1.271,2.677 0.208,0.156 10 false L+ 1.104,3.115 1.271,3.281 0.167,0.167 10 false L- 1.313,0.615 1.5,0.781 0.188,0.167 10 false 11 1.313,1.208 1.5,1.375 0.188,0.167 10 false 9 1.313,1.813 1.5,1.979 0.188,0.167 10 false 10 1.313,2.406 1.5,2.573 0.188,0.167 10 false 7 1.313,3 1.5,3.167 0.188,0.167 10 false 8 5.74,1.229 5.938,1.396 0.198,0.167 10 false 2 5.74,1.813 5.844,1.979 0.104,0.167 10 false 3 5.74,2.396 5.844,2.563 0.104,0.167 10 false 4 5.729,2.99 5.844,3.156 0.115,0.167 10 false 5 5.917,1.323 6.344,1.479 0.427,0.156 10 false CDR+ 5.74,0.625 5.885,0.792 0.146,0.167 10 false 1 5.938,0.719 6.385,0.875 0.448,0.156 10 false CSLD 5.917,1.917 6.344,2.073 0.427,0.156 10 false CDR- 5.917,2.521 6.344,2.677 0.427,0.156 10 false CDL+ 5.917,3.115 6.344,3.271 0.427,0.156 10 false CDL- 5.698,3.5 6.021,3.677 0.323,0.177 10 false F2 5.698,3.677 6.99,4.031 1.292,0.354 10 false Navigation Receiver Assembly 0.448,3.531 0.75,3.698 0.302,0.167 10 false Q21 0.458,3.708 1.656,4.073 1.198,0.365 10 false Television Display Assembly 1.979,3.385 2.74,3.573 0.76,0.188 10 false (Shielded) 3.26,3.385 3.958,3.573 0.698,0.188 10 false (Shielded) 4.5,3.385 5.198,3.573 0.698,0.188 10 false (Shielded)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the F2 navigation receiver assembly connector.


b.

Disconnect the Q21 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-2 (CDR+) - Q21-9 (R+) Always Below 1 Ω
F2-3 (CDR-) - Q21-10 (R-) Always Below 1 Ω
F2-4 (CDL+) - Q21-7 (L+) Always Below 1 Ω
F2-5 (CDL-) - Q21-8 (L-) Always Below 1 Ω
F2-1 (CSLD) - Q21-11 (SLD9) Always Below 1 Ω
F2-2 (CDR+) - Body ground Always 10 kΩ or higher
F2-3 (CDR-) - Body ground Always 10 kΩ or higher
F2-4 (CDL+) - Body ground Always 10 kΩ or higher
F2-5 (CDL-) - Body ground Always 10 kΩ or higher
F2-1 (CSLD) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR