Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059588 NAVIGATION / MULTI INFO DISPLAY _0292199 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D5  Rear Seat Entertainment System Disconnected  


DESCRIPTION

The navigation receiver assembly and television display assembly are connected by the AVC-LAN communication line.

When an AVC-LAN communication error occurs between the navigation receiver assembly and television display assembly, this DTC will be stored.

DTC No. DTC Detection Condition Trouble Area
B15D3 When either condition below is met:
·

Television display assembly is/was not connected while the engine switch is/was on (IG or ACC).

·

Communication between the master unit and the television display assembly is/was not possible when the engine is/was started.


·

Television display assembly power source circuit

·

AVC-LAN circuit between navigation receiver assembly and television display assembly

·

Television display assembly

·

Navigation receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The navigation receiver assembly is the master unit.



WIRING DIAGRAM

E255326E01
0.55,0.631 1.365,0.824 0.816,0.193 10 from Battery 0.337,1.446 1.392,1.644 1.055,0.198 10 from ACC Relay 3.27,2.432 3.608,2.616 0.338,0.184 10 TX+ 3.27,2.827 3.556,3.010 0.287,0.184 10 TX- 5.607,3.214 6.077,3.398 0.470,0.184 10 GND 5.613,2.827 6.000,3.010 0.386,0.184 10 TX- 5.61,2.432 5.996,2.616 0.386,0.184 10 TX+ 5.611,1.428 5.998,1.612 0.386,0.184 10 ACC 5.613,0.642 5.999,0.825 0.386,0.184 10 +B 5.413,2.728 5.598,2.912 0.184,0.184 10 4 5.423,2.341 5.518,2.525 0.094,0.184 10 3 5.422,0.546 5.606,0.730 0.184,0.184 10 1 3.64,2.35 3.820,2.533 0.179,0.184 10 9 3.598,2.731 3.788,2.912 0.190,0.181 10 10 2.492,3.315 2.838,3.499 0.346,0.184 10 F2 5.489,3.881 6.648,4.198 1.159,0.316 10 Television Display Assembly 2.742,0.859 3.490,1.047 0.748,0.188 10 RAD NO. 1 2.742,1.657 3.490,1.846 0.748,0.188 10 RAD NO. 2 5.373,3.119 5.557,3.315 0.184,0.196 10 17 5.422,1.319 5.606,1.503 0.184,0.184 10 2 2.492,3.477 3.825,3.863 1.333,0.387 10 Navigation Receiver Assembly 5.489,3.724 5.785,3.903 0.296,0.178 10 Q21

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the navigation receiver assembly, perform vehicle contract setting (See page Audio / Visual / Telematics>G-BOOK>G-BOOK SYSTEM>REGISTRATION).



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

3.CHECK DTC
3.CHECK DTC

b.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY POWER SOURCE)
a.

Disconnect the Q21 television display assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q21-17 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q21-1 (+B) - Q21-17 (GND) Always 11 to 14 V
Q21-2 (ACC) - Q21-17 (GND) Engine switch on (ACC) 11 to 14 V




OK

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the F2 navigation receiver assembly connector.


b.

Disconnect the Q21 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-9 (TX+) - Q21-3 (TX+) Always Below 1 Ω
F2-10 (TX-) - Q21-4 (TX-) Always Below 1 Ω
F2-9 (TX+) - Body ground Always 10 kΩ or higher
F2-10 (TX-) - Body ground Always 10 kΩ or higher




OK

6.REPLACE TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TELEVISION DISPLAY ASSEMBLY
a.

Replace the television display assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END

NG