Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059588 NAVIGATION / MULTI INFO DISPLAY _0292199 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The navigation receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. DTC Detection Condition Trouble Area
B1579 Telephone microphone signal is lost.
·

Telephone microphone assembly

·

Navigation receiver assembly

·

Harness or connector



WIRING DIAGRAM

E226160E45
0.612,2.065 2.809,2.245 2.198,0.180 10 Telephone Microphone Assembly 4.674,1.861 5.024,2.008 0.350,0.147 10 F17 4.674,2.029 6.667,2.249 1.993,0.220 10 Navigation Receiver Assembly 5.113,1.478 5.492,1.625 0.378,0.147 10 MIN- 5.113,0.68 5.533,0.854 0.420,0.174 10 SNS2 4.842,1.385 5.023,1.531 0.181,0.147 10 19 4.895,0.586 5.013,0.761 0.118,0.174 10 6 1.669,1.483 2.110,1.630 0.440,0.147 10 MIC- 1.67,0.677 2.082,0.852 0.412,0.174 10 SNSE 2.157,1.38 2.336,1.527 0.179,0.147 10 2 2.157,0.582 2.354,0.756 0.198,0.174 10 3 0.612,1.885 0.962,2.032 0.350,0.147 10 Q17

CAUTION / NOTICE / HINT

NOTICE:

When replacing the navigation receiver assembly, perform vehicle contract setting (See page Audio / Visual / Telematics>G-BOOK>G-BOOK SYSTEM>REGISTRATION).


PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
U189950E02
2.073,1.99 2.427,2.583 false 0.156,0.104 0.365,0.323 0.208,0.219 10 false *a 1.604,0.729 1.969,0.927 0.365,0.198 10 false F17 2.271,2.625 2.688,2.823 0.417,0.198 10 false MIN-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-19 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the F17 navigation receiver assembly connector.


b.

Disconnect the Q17 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-6 (SNS2) - Q17-3 (SNSE) Always Below 1 Ω
F17-19 (MIN-) - Q17-2 (MIC-) Always Below 1 Ω
F17-6 (SNS2) - Body ground Always 10 kΩ or higher
F17-19 (MIN-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT TELEPHONE MICROPHONE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.
U189944E02
1.573,1.615 1.208,1.813 false 1.865,1.292 2.25,1.458 false 1.604,0.333 1.885,0.51 0.281,0.177 10 false Q17 0.167,0.063 0.365,0.26 0.198,0.198 10 false *a 0.76,1.771 1.177,1.969 0.417,0.198 10 false SNSE 2.313,1.427 2.74,1.625 0.427,0.198 10 false MIC-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q17-3 (SNSE) - Q17-2 (MIC-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Telephone Microphone Assembly)



OK

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY