Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292203 PARKING ASSIST MONITOR SYSTEM U

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


a.

Disconnect the S20 rear television camera assembly connector.

U189917E02
3.563,0.781 3.865,0.948 0.302,0.167 10 false S20


b.

Measure the voltage of each terminal of the wire harness side connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S20-4 (CB+) - Body ground B - Body ground Power source Engine switch on (IG), shift lever in R 5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the S20 rear television camera assembly connector.


d.

Check for pulses between each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S20-2 (CV+) - S20-3 (CGND) R - W Display signal
·

Engine switch on (IG)

·

Shift lever in R

·

Camera lens not covered, displaying an image


Pulse generation
(See waveform 1)
·

Engine switch on (IG)

·

Shift lever in R

·

Camera lens covered, blacking out the screen


Pulse generation
(See waveform 2)

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


If the result is not as specified, the rear television camera assembly may have a malfunction.


e.

Reference (Oscilloscope waveform):

E359675E01
0.958,2.313 1.177,2.313 1.177,2.313 1.323,1.792 false 1.792,2.333 1.604,2.333 1.604,2.333 1.427,1.698 false 4.083,2.333 4.302,2.333 4.302,2.333 4.479,1.646 false 5,2.333 4.813,2.333 4.813,2.333 4.604,1.604 false 0.594,0.25 0.823,0.479 0.229,0.229 10 false *a 0.542,1.271 0.979,1.51 0.438,0.24 10 false GND 0.771,2.219 1,2.427 0.229,0.208 10 false *c 1.844,2.229 2.094,2.448 0.25,0.219 10 false *d 3.677,0.229 3.896,0.458 0.219,0.229 10 false *b 3.667,1.271 4.104,1.51 0.438,0.24 10 false GND 5.052,2.25 5.302,2.469 0.25,0.219 10 false *d 3.896,2.229 4.125,2.438 0.229,0.208 10 false *c

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Terminal No. (Symbol) S20-2 (CV+) - S20-3 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), shift lever in R

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Terminal No. (Symbol) S20-2 (CV+) - S20-3 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), shift lever in R

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


Text in Illustration
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform