Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292203 PARKING ASSIST MONITOR SYSTEM D

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR DIAGNOSIS SYSTEM


a.

For parking assist monitor system diagnosis, signals received by the navigation receiver assembly can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the navigation receiver assembly.

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).


HINT:

The displayed items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (during parking assist monitor system initialization)


E278001E01
0.144,0.059 1.404,0.305 1.260,0.246 12 Example:

E276173


DIAGNOSIS SCREEN TRANSITION (after parking assist monitor system initialization)


E278003E01
0.149,0.046 1.145,0.306 0.996,0.260 12 Example:

E258590


VEHICLE SIGNAL CHECK (navigation system input signals)



b.
E226190

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting" screen.


c.
E226193

Select "Vehicle Signal" on the "Function Check/Setting" screen.


d.
E225776

Vehicle Signal Check Mode

i.

When the "Vehicle Signal Check Mode" screen is displayed, check "REV" the vehicle signal conditions.

HINT:
·

Only conditions having inputs are displayed.

·

This screen displays vehicle signals input to the navigation receiver assembly.

·

For details of this function, refer to Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK)







CAR SIGNAL CHECK (parking assist monitor system input signals)


a.

Start diagnostic mode (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

i.
E226190

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting" screen.


ii.
E226193

Select "Camera Setting" on the "Function Check/Setting" screen.


iii.
E226194

Select "Next" on the "Car Information Check" screen.

HINT:

After "Next" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the navigation receiver assembly was replaced.

Parking Assist Monitor System Initialization Screen Transition
Not performed Car Signal Check screen
Performed Mode Setting screen



iv.
E233966

When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Car Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.
E233967

Car Signal Check

i.

On the "Car Signal Check" screen, it is possible to inspect the state of signals and check the settings.

Item Inspection Detail Note
BCTY Back door courtesy light switch signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

BCTY inspection

HINT:

If "CHK" (red) is displayed for "BCTY", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>DTC CHECK / CLEAR).





CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).