Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292203 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the navigation receiver assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem.

DTC No. DTC Detection Condition Trouble Area
C1625 Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E224380E30
1.121,3.216 2.868,3.391 1.747,0.175 10 : CAN Communication Line 3.226,0.601 3.584,0.776 0.358,0.174 10 BAT 3.226,1.711 3.556,1.886 0.330,0.174 10 ESS 2.106,1.314 2.853,1.489 0.747,0.174 10 RH ECU-IG 2.258,0.766 2.710,0.940 0.452,0.174 10 ECU-B 0.439,1.159 1.787,1.313 1.347,0.154 10 from RH-IG Relay 1 0.916,0.591 1.847,0.765 0.930,0.174 10 from Battery 3.19,2.326 4.258,2.742 1.068,0.416 10 Steering Sensor 3.033,0.507 3.156,0.682 0.123,0.174 10 3 3.033,1.05 3.156,1.225 0.123,0.174 10 1 3.033,1.604 3.156,1.778 0.123,0.174 10 2 3.226,1.158 3.528,1.332 0.303,0.174 10 IG 3.201,2.16 3.540,2.335 0.339,0.174 10 G18 4.993,2.186 6.927,2.536 1.934,0.350 10 Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SUPPLY)
a.
U189919E01
1.611,1.128 1.892,1.267 0.281,0.139 10 G18 0.201,0.193 0.352,0.340 0.151,0.147 10 *a 0.917,2.433 0.573,2.433 false 0.372,2.347 0.538,2.494 0.165,0.147 10 IG 0.67,2.863 0.988,3.010 0.318,0.147 10 ESS 1.375,2.857 1.693,3.004 0.318,0.147 10 BAT 1.103,2.488 0.831,2.84 false 1.315,2.479 1.527,2.846 false

Disconnect the G18 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-2 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G18-1 (IG) - G18-2 (ESS) Engine switch on (IG) 11 to 14 V
G18-3 (BAT) - G18-2 (ESS) Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR