Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292203 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the navigation receiver assembly judges that the signals or signal lines between the navigation receiver assembly and the rear television camera assembly are not normal as a result of its self check.

DTC No. DTC Detection Condition Trouble Area
C1622 Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Navigation receiver assembly



WIRING DIAGRAM

E254359E02
0.135,3.396 2.073,3.75 1.938,0.354 10 false Navigation Receiver Assembly 5.396,1.208 5.573,1.375 0.177,0.167 10 false 2 5.396,1.76 5.573,1.927 0.177,0.167 10 false 3 5.396,0.667 5.573,0.833 0.177,0.167 10 false 4 5.396,2.313 5.573,2.479 0.177,0.167 10 false 1 5.635,1.396 6.052,1.563 0.417,0.167 10 false CV+ 5.635,2.469 6.052,2.635 0.417,0.167 10 false CV- 5.635,0.844 6.052,1.01 0.417,0.167 10 false CB+ 5.635,1.917 6.104,2.083 0.469,0.167 10 false CGND 2.021,1.677 2.219,1.844 0.198,0.167 10 false 15 2.021,2.208 2.219,2.375 0.198,0.167 10 false 16 2.063,2.75 2.26,2.917 0.198,0.167 10 false 7 1.604,1.396 2.021,1.563 0.417,0.167 10 false V+ 1.604,2.469 2.021,2.635 0.417,0.167 10 false V- 1.521,0.833 1.938,1 0.417,0.167 10 false CA+ 1.396,1.917 1.865,2.083 0.469,0.167 10 false CGND 1.49,3 1.854,3.167 0.365,0.167 10 false GND 5.469,3.552 7.021,3.906 1.552,0.354 10 false Rear Television Camera Assembly 3.188,3.833 4.094,4.042 0.906,0.208 10 false *1: Shielded 3.854,2.094 4.104,2.292 0.25,0.198 10 false *1 2.063,1.135 2.24,1.302 0.177,0.167 10 false 8 2.063,0.615 2.24,0.781 0.177,0.167 10 false 7 5.469,3.385 5.781,3.552 0.313,0.167 10 false S20 1.969,1.375 2.281,1.542 0.313,0.167 10 false F18 1.99,1.906 2.302,2.073 0.313,0.167 10 false F18 1.979,0.844 2.313,1.01 0.333,0.167 10 false F18 1.979,2.448 2.302,2.615 0.323,0.167 10 false F18 1.979,2.979 2.25,3.146 0.271,0.167 10 false F13

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F18 and F13 navigation receiver assembly connectors.


b.

Disconnect the S20 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-7 (CA+) - S20-4 (CB+) Always Below 1 Ω
F18-8 (V+) - S20-2 (CV+) Always Below 1 Ω
F18-15 (CGND) - S20-3 (CGND) Always Below 1 Ω
F18-16 (V-) - S20-1 (CV-) Always Below 1 Ω
F18-7 (CA+) - Body ground Always 10 kΩ or higher
F18-8 (V+) - Body ground Always 10 kΩ or higher
F18-15 (CGND) - Body ground Always 10 kΩ or higher
F18-16 (V-) - Body ground Always 10 kΩ or higher
F13-7 (GND) - Body ground Always Below 1 Ω




OK

2.INSPECT NAVIGATION RECEIVER ASSEMBLY (V-, CGND, CA+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NAVIGATION RECEIVER ASSEMBLY (V-, CGND, CA+)
a.
U189933E02
1.385,1.781 1.073,2.448 1.073,2.448 0.74,2.448 false 1.24,1.781 0.719,1.781 false 1.375,1.604 1.063,0.927 1.063,0.927 0.729,0.927 false 0.5,1.688 0.833,1.865 0.333,0.177 10 false V- 0.25,2.365 0.688,2.542 0.438,0.177 10 false CGND 0.167,0.104 0.604,0.281 0.438,0.177 10 false *a 1.563,0.438 1.906,0.615 0.344,0.177 10 false F18 0.396,0.844 0.729,1.021 0.333,0.177 10 false CA+

Reconnect the F18 and F13 navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-16 (V-) - Body ground Always Below 1 Ω
F18-15 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F18-7 (CA+) - F18-16 (V-) Engine switch on (IG)
Shift lever in R
5.5 to 7.05 V


Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)



OK

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY (V+, GND)

NG

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY (V+, GND)
a.

Reconnect the S20 rear television camera assembly connector.


b.

Reconnect the F18 and F13 navigation receiver assembly connectors.

E358408E01
1.833,0.25 2.25,0.5 0.417,0.25 1.583,1.875 2,2.125 0.417,0.25 1.792,1.063 1.792,1 1.792,1 1.448,1 false 1.313,3.042 1.594,3.042 1.594,3.042 1.885,2.75 false 4.281,1.969 4.448,1.969 4.448,1.969 4.542,1.625 false 4.969,2.01 4.802,2.01 4.802,2.01 4.646,1.521 false 4.313,3.563 4.479,3.563 4.479,3.563 4.583,3.125 false 5.01,3.552 4.844,3.552 4.844,3.552 4.688,3.063 false 0.115,0.083 0.49,0.323 0.375,0.24 10 false *a 3.625,0.219 4,0.458 0.375,0.24 10 false *b 3.667,2.24 4.042,2.479 0.375,0.24 10 false *c 3.823,1.156 4.198,1.396 0.375,0.24 10 false GND 1.917,0.292 2.292,0.531 0.375,0.24 10 false F18 1.667,1.917 2.042,2.156 0.375,0.24 10 false F13 1.208,0.917 1.583,1.156 0.375,0.24 10 false V+ 4.104,1.875 4.479,2.115 0.375,0.24 10 false *d 4.979,1.906 5.354,2.146 0.375,0.24 10 false *e 3.823,2.781 4.198,3.021 0.375,0.24 10 false GND 0.958,2.958 1.333,3.198 0.375,0.24 10 false GND 4.125,3.479 4.5,3.719 0.375,0.24 10 false *d 5.052,3.479 5.427,3.719 0.375,0.24 10 false *e

Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)
*b Waveform 1 (camera lens is not covered, displaying an image)
*c Waveform 2 (camera lens is covered, blacking out the screen)
*d Synchronization Signal
*e Video Waveform


c.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) F18-8 (V+) - F13-7 (GND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), shift lever in R

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.




OK

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY