Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2013.04–2016.05
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292208 TOYOTA PARKING ASSIST-SENSOR SYSTEM U

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  TERMINALS OF ECU  


CHECK CLEARANCE WARNING ECU ASSEMBLY (for Type A)


U186126E03
3.365,0.167 3.688,0.344 0.323,0.177 10 false G23

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G23-1 (PL) - G23-21 (E) BE - W-B Shift lever P position signal
·

Engine switch on (IG)

·

Shift lever in any position other than P


Below 1 V
G23-3 (SPD) - G23-21 (E) W - W-B Vehicle speed signal
·

Engine switch on (IG)

·

Drive wheels are turned slowly


Repeat between 1.5 to 4.5 V
G23-6 (SOR) LG -
·

Engine switch on (IG)

·

Clearance sonar main switch on


-
G23-7 (SOF) L -
·

Engine switch on (IG)

·

Clearance sonar main switch on


-
G23-9 (BOF) - G23-21 (E) V - W-B Power source for front sensor circuit
·

Engine switch on (IG)

·

Clearance sonar main switch on


7.2 to 8.8 V
G23-10 (IG) - G23-21 (E) L - W-B IG power source signal
·

Engine switch on (IG)

·

Clearance sonar main switch off


Below 1 V
·

Engine switch on (IG)

·

Clearance sonar main switch on


11 to 14 V
G23-11 (TL) - G23-21 (E) G - W-B Illumination signal Light control switch off Below 1 V
Light control switch in tail or head position 11 to 14 V
G23-12 (BBZ) - G23-21 (E) P - W-B Clearance warning buzzer signal Buzzer sounding Pulse generation
(See waveform 1)
G23-13 (RL) - G23-21 (E) LG - W-B Shift lever R position signal
·

Engine switch on (IG)

·

Shift lever in any position other than R


Below 1 V
·

Engine switch on (IG)

·

Shift lever in R


11 to 14 V
G23-15 (L1) - G23-21 (E) SB - W-B Clearance sonar indicator light (rear right corner) signal When No. 1 ultrasonic sensor (rear right corner) detects obstacle Below 3 V
G23-16 (L2) - G23-21 (E) V - W-B Clearance sonar indicator light (front right corner) signal When No. 1 ultrasonic sensor (front right corner) detects obstacle Below 3 V
G23-17 (L3) - G23-21 (E) GR - W-B Clearance sonar indicator light (rear left corner) signal When No. 1 ultrasonic sensor (rear left corner) detects obstacle Below 3 V
G23-18 (L4) - G23-21 (E) B - W-B Clearance sonar indicator light (front left corner) signal When No. 1 ultrasonic sensor (front left corner) detects obstacle Below 3 V
G23-19 (L5) - G23-21 (E) SB - W-B Clearance sonar indicator light (rear center) signal When No. 1 ultrasonic sensor (rear left center) or No. 1 ultrasonic sensor (rear right center) detects obstacle Below 3 V
G23-20 (L6) - G23-21 (E) W - W-B Power indicator light signal
·

Engine switch on (IG)

·

Clearance sonar main switch on


Below 3 V
G23-21 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
G23-22 (E2) - G23-21 (E) L - W-B Ground Always Below 1 Ω
G23-23 (E1) - G23-21 (E) P - W-B Ground Always Below 1 Ω
G23-24 (BOR) - G23-21 (E) G - W-B Power source for rear sensor circuit
·

Engine switch on (IG)

·

Clearance sonar main switch on


7.2 to 8.8 V

a.

Using an oscilloscope, check waveform 1.

i.
C365690E02
0.104,1.677 0.469,1.875 0.365,0.198 10 false GND

Waveform 1 (Reference)

Item Content
Terminal No. (Symbol) G23-12 (BBZ) - G23-21 (E)
Tool Setting 2 V/DIV., 200 μsec. / DIV.
Vehicle Condition Buzzer sounding




CHECK CLEARANCE WARNING ECU ASSEMBLY (for Type B)


U189979E02
3.469,0.375 3.823,0.531 0.354,0.156 10 false G108

a.

Disconnect the G108 clearance warning ECU assembly connector.


b.

Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G108-6 (PL) - G108-16 (E) BE - W-B Shift lever P position signal
·

Engine switch on (IG)

·

Shift lever in any position other than P


Below 1 V
·

Engine switch on (IG)

·

Shift lever in P


11 to 14 V
G108-11 (IG) - G108-16 (E) W - W-B IG power source signal Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
G108-16 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
G108-19 (CLSW) - G108-16 (E) W - W-B Clearance sonar main switch power source signal
·

Engine switch on (IG)

·

Clearance sonar main switch off


Below 1 V
·

Engine switch on (IG)

·

Clearance sonar main switch on


11 to 14 V
G108-20 (TL) - G108-16 (E) G - W-B Illumination signal Light control switch in tail or head position 11 to 14 V
G108-21 (RL) - G108-16 (E) LG - W-B Shift lever R position signal
·

Engine switch on (IG)

·

Shift lever in any position other than R


Below 1 V
·

Engine switch on (IG)

·

Shift lever in R


11 to 14 V


c.

Reconnect the G108 clearance warning ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G108-2 (ER) - G108-16 (E) P - W-B Clearance warning buzzer signal Buzzer sounding Pulse generation (See waveform 1)
G108-3 (BOF) - G108-16 (E) V - W-B Power source for front sensor circuit Engine switch off Below 1 V
·

Engine switch on (IG)

·

Clearance sonar main switch on


7.2 to 8.8 V
G108-4 (E5) - G108-16 (E) P - W-B Ground for sensor (Front sensor) Always Below 1 V
G108-5 (SOF) - G108-16 (E) L - W-B Sensor communication signal (Front sensor)
·

Engine switch on (IG)

·

Clearance sonar main switch on

·

Shift lever in R


Pulse generation (See waveform 2)
G108-7 (L1) - G108-16 (E) SB - W-B Clearance sonar indicator light (rear right corner) signal When No. 1 ultrasonic sensor (rear right corner) detects obstacle Below 3 V
G108-8 (L2) - G108-16 (E) V - W-B Clearance sonar indicator light (front right corner) signal When No. 1 ultrasonic sensor (rear left corner) detects obstacle Below 3 V
G108-9 (L4) - G108-16 (E) B - W-B Clearance sonar indicator light (front left corner) signal When No. 1 ultrasonic sensor (front right corner) detects obstacle Below 3 V
G108-10 (L10) - G108-16 (E) W - W-B Power indicator light signal
·

Engine switch on (IG)

·

Clearance sonar switch on


Below 3 V
G108-12 (BOR) - G108-16 (E) G - W-B Power source for rear sensor circuit Engine switch off Below 1 V
·

Engine switch on (IG)

·

Clearance sonar main switch on


7.2 to 8.8 V
G108-13 (E1) - G108-16 (E) L - W-B Ground for sensor (Rear sensor) Always Below 1 V
G108-14 (SOR) - G108-16 (E) LG - W-B Sensor communication signal (Rear sensor)
·

Engine switch on (IG)

·

Clearance sonar main switch on

·

Shift lever in R


Pulse generation (See waveform 2)
G108-17 (SPD) - G108-16 (E) W - W-B Vehicle speed signal
·

Engine switch on (IG)

·

Wheel being rotated


Pulse generation (See waveform 3)
G108-23 (L3) - G108-16 (E) GR - W-B Clearance sonar indicator light (rear left corner) signal When No. 1 ultrasonic sensor (rear left center) or No. 1 ultrasonic sensor (rear right center) detects obstacle Below 3 V
G108-24 (L5) - G108-16 (E) SB - W-B Clearance sonar indicator light (rear center) signal When No. 1 ultrasonic sensor (front left corner) detects obstacle Below 3 V


e.

Using an oscilloscope, check waveform.

i.
E227014E06
0.083,1.677 0.552,1.938 0.469,0.26 10 GND

Waveform 1 (Reference)

Item Content
Terminal No. (Symbol) G108-2 (ER) - G108-16 (E)
Tool Setting 2 V/DIV., 500 μsec./DIV.
Vehicle Condition Buzzer sounding


ii.
E231486E07
0.188,0.927 0.625,1.146 0.438,0.219 10 false GND 0.188,1.542 0.719,1.792 0.531,0.25 10 false GND 0.052,0.604 0.458,0.771 0.406,0.167 10 false CH1: 0.052,1.229 0.458,1.396 0.406,0.167 10 false CH2:

Waveform 2 (Reference)

Item Content
Terminal No. (Symbol)
·

CH1: G108-5 (SOF) - G108-16 (E)

·

CH2: G108-14 (SOR) - G108-16 (E)


Tool Setting 5 V/DIV., 1 msec./DIV.
Vehicle Condition
·

Engine switch on (IG)

·

Clearance sonar main switch on

·

Shift lever in R




iii.
E284591E02
0.208,1.125 0.698,1.375 0.49,0.25 10 false GND 1.5,1.406 1.99,1.656 0.49,0.25 10 false A

Waveform 3 (Reference)

Item Content
Terminal No. (Symbol) G108-17 (SPD) - G108-16 (E)
Tool Setting 5 V/DIV., 20 msec./DIV.
Vehicle Condition
·

Engine switch on (IG)

·

Wheel being rotated



HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.