Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2013.04–2016.05
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292208 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Taillight Circuit  


WIRING DIAGRAM

for Type A


E256012E01
4.467,1.4 4.777,1.575 0.311,0.174 10 G23 4.467,1.559 6.645,1.734 2.179,0.174 10 Clearance Warning ECU Assembly 5.207,0.858 5.404,1.032 0.196,0.174 10 TL 4.94,0.755 5.114,0.930 0.174,0.174 10 11 0.733,0.84 1.755,1.015 1.022,0.174 10 from TAIL Relay 3.342,0.984 3.818,1.158 0.476,0.174 10 PANEL


for Type B


E256012E03
4.467,1.4 5.041,1.575 0.575,0.174 10 G108 4.467,1.559 6.645,1.734 2.179,0.174 10 Clearance Warning ECU Assembly 5.207,0.858 5.404,1.032 0.196,0.174 10 TL 4.94,0.755 5.114,0.930 0.174,0.174 10 20 0.733,0.84 1.755,1.015 1.022,0.174 10 from TAIL Relay 3.342,0.984 3.818,1.158 0.476,0.174 10 PANEL


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for Type A A
for Type B B




A

2.CHECK TAILLIGHT

B

4.CHECK TAILLIGHT
2.CHECK TAILLIGHT
a.

Check that the taillight comes on when the light control switch to the tail or head position.


b.

Check that the taillight turns on.

OK:

Taillight turns on.




OK

3.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

NG

3.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the G23 clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) is the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G23-11 (TL) - Body ground Engine switch on (IG)
Light control switch in the tail or head position
11 to 14 V




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TAILLIGHT
a.

Check that the taillight comes on when the light control switch to the tail or head position.


b.

Check that the taillight turns on.

OK:

Taillight turns on.




OK

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

NG

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the G108 clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) is the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G108-20 (TL) - Body ground Engine switch on (IG)
Light control switch in the tail or head position
11 to 14 V




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR