Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2013.04–2016.05
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292208 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the clearance warning ECU assembly.

WIRING DIAGRAM

for Type A


E256013E02
2.525,1.393 2.831,1.568 0.306,0.174 10 G24 2.525,1.552 4.939,1.884 2.414,0.332 10 Clearance Warning Indicator Assembly (Clearance Sonar Main Switch) 5.377,1.393 5.688,1.568 0.311,0.174 10 G23 5.377,1.552 6.912,1.884 1.536,0.332 10 Clearance Warning ECU Assembly 3.9,0.621 4.102,0.795 0.202,0.174 10 SK 3.377,0.621 3.591,0.795 0.213,0.174 10 BD 4.175,0.527 4.272,0.702 0.097,0.174 10 7 3.208,0.53 3.305,0.704 0.097,0.174 10 8 5.512,1.005 5.684,1.179 0.173,0.174 10 21 5.512,0.527 5.684,0.702 0.173,0.174 10 10 5.763,0.618 6.066,0.793 0.303,0.174 10 IG 0.27,0.615 1.492,0.947 1.223,0.332 10 from LH-IG Relay 2 2.103,0.769 2.986,0.944 0.883,0.174 10 GAUGE NO.1 5.763,1.096 5.953,1.271 0.190,0.174 10 E


for Type B


E274582E11
0.51,0.708 1.865,0.948 1.354,0.24 10 false from LH-IG Relay 2 2.531,0.865 3.448,1.031 0.917,0.167 10 false GAUGE NO.1 5.083,2 5.5,2.188 0.417,0.188 10 false G108 5.094,2.167 6.625,2.563 1.531,0.396 10 false Clearance Warning ECU Assembly 5.229,0.594 5.479,0.76 0.25,0.167 10 false 11 5.229,1.365 5.479,1.531 0.25,0.167 10 false 16 5.5,1.479 5.667,1.646 0.167,0.167 10 false E 5.5,0.698 5.667,0.896 0.167,0.198 10 false IG


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for Type A A
for Type B B




A

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY POWER SOURCE)

B

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY POWER SOURCE)
a.

Disconnect the G23 clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) is the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G23-10 (IG) - Body ground Engine switch on (IG)
Clearance sonar main switch on
11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-21 (E) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY POWER SOURCE)
a.

Disconnect the G108 clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) is the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G108-11 (IG) - Body ground Engine switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G108-16 (E) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR