CHECK INITIAL CHECK FUNCTION
Check the initial check function for the clearance warning indicator.
Turn the engine switch on (IG).
Adjust the shift lever to the R position (when the back sonar and rear clearance sonar is checked).
Adjust the shift lever to the N position (when the front clearance sonar is checked).
Apply the parking brake securely so that the vehicle does not move.
When the clearance sonar main switch is turned on, check that the following occurs: 1) after 0.4 seconds, the indicator illuminates for approximately 0.7 to 1.3 seconds, and 2) the system starts the obstacle detection operation.
If the sensor is found to have an anomaly due to an open circuit or freezing for approximately 5 seconds or more, indications as shown in the following illustration appear.
If a sensor has an open circuit or a sensor's detection operation malfunctions because it is wet or frozen, the buzzer sounds.
When the sensor condition returns to normal, the system ends normal clearance sonar mode and returns to steering sensing mode.
If the clearance sonar main switch is on and the engine switch is turned on (IG), the buzzer does not sound.
DETECTION RANGE MEASUREMENT AND INDICATOR CHECK
The following measurement and inspection will be performed with the shift lever in a position other than P. Be sure to apply the parking brake and depress the brake pedal firmly to prevent the vehicle from moving.
Turn the engine switch on (IG).
Turn the clearance sonar main switch on.
Detection range measurement:
When measuring the detection range of the front corner sonar, move the shift lever to any position other than P.
When measuring the detection range of the rear corner sonar and rear center sonar, move the shift lever to R.
Move a 60 mm (2.4 in.) diameter pole near each sensor to measure its detection range.
These detection ranges are applicable when positioning the 60 mm (2.4 in.) diameter pole parallel or perpendicular to the ground. The detection range varies depending on the measuring method and type of obstacle (such as walls).
Have an assistant move the pole.
The ultrasonic sensor side view detection range (hatched area labeled (B)) represents the cross section of the top view detection range (A). The hatched area (B) does not represent the entire side view detection range.
Check the clearance warning indicator and the buzzer sounding condition when the front corner ultrasonic sensors and rear corner ultrasonic sensors detect an obstacle.
| Clearance sonar | Engine switch | Clearance sonar main switch | Shift position | Vehicle speed |
|---|---|---|---|---|
| Front | On (IG) | On | Position other than P | 10 km/h (6 mph) or less |
| R position | - | |||
| Rear | On (IG) | On | R position | - |
| Detection Range | Obstacle |
|---|---|
| Close-range detection
Within approx. 300 +/- 30 mm (11.8 +/- 1.2 in.) |
60 mm (2.36 in.) diameter pole |
| Medium-range detection
From approx. 300 +/- 30 to 450 +/- 50 mm (11.8 +/- 1.2 to 17.7 +/- 2.0 in.) |
60 mm (2.36 in.) diameter pole |
| Long-range detection
From approx. 450 +/- 50 to 600 +/- 60 mm (17.7 +/- 2.0 to 23.6 +/- 2.4 in.) |
60 mm (2.36 in.) diameter pole |
Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.
If one of the back sonar sensors is faulty, the other sensors will not be able to detect obstacles.
Check the clearance warning indicator and the buzzer sounding condition when the rear center ultrasonic sensors detect an obstacle.
| Engine switch | Clearance sonar main switch | Shift position | Vehicle speed |
|---|---|---|---|
| On (IG) | On | R position | - |
| Detection Range | Obstacle |
|---|---|
| Close-range detection
Within approx. 350 +/- 40 mm (13.8 +/- 1.6 in.) |
60 mm (2.36 in.) diameter pole |
| Medium-range detection
From approx. 350 +/- 40 to 450 +/- 50 mm (13.8 +/- 1.6 to 17.7 +/- 2.0 in.) |
60 mm (2.36 in.) diameter pole |
| Long-range detection
From approx. 450 +/- 50 to 600 +/- 60 mm (17.7 +/- 2.0 to 23.6 +/- 2.4 in.) |
60 mm (2.36 in.) diameter pole |
| Longest-range detection
From approx. 600 +/- 60 to 1500 +/- 150 mm (23.6 +/- 2.4 to 59.1 +/- 5.9 in.) |
Wall |
Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.
If one of the back sonar sensors is faulty, the other sensors will not be able to detect obstacles.