Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for RHD) › from 2016.05
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292210 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for RHD) U

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for RHD)  TERMINALS OF ECU  


CLEARANCE WARNING ECU ASSEMBLY


U189936E02
3.417,0.219 3.781,0.396 0.365,0.177 10 false G111

a.

Disconnect the G111 clearance warning ECU assembly connector.


b.

Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G111-9 (CLSW) - G111-30 (E) SB - W-B Clearance sonar main switch (combination switch assembly) power source signal Engine switch on (IG)
Clearance sonar main switch (combination switch assembly) on
11 to 14 V
Engine switch on (IG)
Clearance sonar main switch (combination switch assembly) off
Below 1 V
G111-1 (IG) - G111-30 (E) L - W-B IG power source signal Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
G111-30 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the G111 clearance warning ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G111-22 (BOR) - G111-30 (E) G - W-B Power source for rear sensor circuit Engine switch off Below 1 V
Engine switch on (IG)
Clearance sonar main switch (combination switch assembly) on
7.2 to 8.8 V
G111-8 (SOF) - G111-30 (E) BE - W-B Front sensor communication signal (Front clearance sonar sensor) Engine switch on (IG)
Clearance sonar main switch (combination switch assembly) on
Shift lever in R
Pulse generation
(See waveform 2)
G111-13 (EF) - G111-30 (E) V - P Clearance warning buzzer signal Buzzer sounding Pulse generation
(See waveform 1)
G111-23 (E1) - G111-30 (E) L - W-B Ground for rear clearance sonar Always Below 1 V
G111-6 (E5) - G111-30 (E) Y - W-B Ground for front clearance sonar Always Below 1 V
G111-4 (BOF) - G111-30 (E) L - W-B Power source for front sensor circuit Engine switch off Below 1 V
Engine switch on (IG)
Clearance sonar main switch (combination switch assembly) on
7.2 to 8.8 V
G111-24 (SOR) - G111-30 (E) LG - W-B Rear sensor communication signal (Rear clearance sonar sensor) Engine switch on (IG)
Clearance sonar main switch (combination switch assembly) on
Shift lever in R
Pulse generation
(See waveform 2)


e.

Using an oscilloscope, check waveform.

i.
E227014E06
0.083,1.677 0.552,1.938 0.469,0.26 10 GND

Waveform 1 (Reference)

Item Content
Terminal No. (Symbol) GG111-13 (EF) - G111-30 (E)
Tool Setting 2 V/DIV., 500 μsec./DIV.
Condition Buzzer sounding

HINT:

The amplitude of the waveform changes according to the set volume.



ii.
E231486E08
0.188,0.927 0.625,1.146 0.438,0.219 10 false GND 0.188,1.552 0.719,1.802 0.531,0.25 10 false GND 0.104,0.635 0.51,0.802 0.406,0.167 10 false CH1: 0.083,1.281 0.49,1.448 0.406,0.167 10 false CH2:

Waveform 2 (Reference)

Item Content
Terminal No. (Symbol)
·

CH1: G111-8 (SOF) - G111-30 (E)

·

CH2: G111-24 (SOR) - G111-30 (E)


Tool Setting 5 V/DIV., 1 msec./DIV.
Condition Engine switch on (IG)
Clearance sonar main switch (combination switch assembly) on
Shift lever in R

HINT:

The waveforms for CH1 and CH2 are same.