CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)
Disconnect the J5*1 or I5*2 motor connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B (J5-2) - GND (J5-1) | B - W-B | Battery power supply | Always | 10 to 14 V |
| GND (J5-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B (I5-2) - GND (I5-1) | B - W-B | Battery power supply | Always | 10 to 14 V |
| GND (I5-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the J5*1 or I5*2 motor connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| LIN (J5-9) - GND (J5-1) | R - W-B | LIN communication line | Always | Pulse generation |
| UP (J5-10) - GND (J5-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| UP (J5-10) - GND (J5-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| DOWN (J5-7) - GND (J5-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| DOWN (J5-7) - GND (J5-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| LIN (I5-9) - GND (I5-1) | R - W-B | LIN communication line | Always | Pulse generation |
| UP (I5-10) - GND (I5-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| UP (I5-10) - GND (I5-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| DOWN (I5-7) - GND (I5-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| DOWN (I5-7) - GND (I5-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
If the result is not as specified, the motor may be malfunctioning.
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side)
Disconnect the I5*1 or J5*2 motor connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B (I5-2) - GND (I5-1) | B - W-B | Battery power supply | Always | 10 to 14 V |
| GND (I5-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B (J5-2) - GND (J5-1) | B - W-B | Battery power supply | Always | 10 to 14 V |
| GND (J5-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the I5*1 or J5*2 motor connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| LIN (I5-9) - GND (I5-1) | R - W-B | LIN communication line | Always | Pulse generation |
| UP (I5-10) - GND (I5-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| UP (I5-10) - GND (I5-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| DOWN (I5-7) - GND (I5-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| DOWN (I5-7) - GND (I5-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| LIN (J5-9) - GND (J5-1) | R - W-B | LIN communication line | Always | Pulse generation |
| UP (J5-10) - GND (J5-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| UP (J5-10) - GND (J5-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| DOWN (J5-7) - GND (J5-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| DOWN (J5-7) - GND (J5-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
If the result is not as specified, the motor may be malfunctioning.
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH)
Disconnect the L2 motor connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B (L2-2) - GND (L2-1) | L - W-B | Battery power supply | Always | 10 to 14 V |
| GND (L2-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the L2 motor connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| LIN (L2-9) - GND (L2-1) | R - W-B | LIN communication line | Always | Pulse generation |
| UP (L2-10) - GND (L2-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| UP (L2-10) - GND (L2-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| DOWN (L2-7) - GND (L2-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| DOWN (L2-7) - GND (L2-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
If the result is not as specified, the motor may be malfunctioning.
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH)
Disconnect the K2 motor connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B (K2-2) - GND (K2-1) | L - W-B | Battery power supply | Always | 10 to 14 V |
| GND (K2-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the K2 motor connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| LIN (K2-9) - GND (K2-1) | R - W-B | LIN communication line | Always | Pulse generation |
| UP (K2-10) - GND (K2-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| UP (K2-10) - GND (K2-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| DOWN (K2-7) - GND (K2-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| DOWN (K2-7) - GND (K2-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
If the result is not as specified, the motor may be malfunctioning.
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
Disconnect the J12*1 or I14*2 master switch connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B (J12-11) - GND (J12-12) | R - W-B | Ignition power supply | Engine switch off | Below 1 V |
| B (J12-11) - GND (J12-12) | R - W-B | Ignition power supply | Engine switch on (IG) | 10 to 14 V |
| GND (J12-12) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B (I14-11) - GND (I14-12) | R - W-B | Ignition power supply | Engine switch off | Below 1 V |
| B (I14-11) - GND (I14-12) | R - W-B | Ignition power supply | Engine switch on (IG) | 10 to 14 V |
| GND (I14-12) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the J12*1 or I14*2 master switch connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| LIN2 (J12-16) - GND (J12-12) | R - W-B | LIN communication line | Always | Pulse generation |
| LIN1 (J12-17) - GND (J12-12) | R - W-B | LIN communication line | Always | Pulse generation |
| UP (J12-20) - GND (J12-12) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| UP (J12-20) - GND (J12-12) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| DOWN (J12-15) - GND (J12-12) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| DOWN (J12-15) - GND (J12-12) | G - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
| LED (J12-18) - GND (J12-12) | L - W-B | Illuminates when power window operation permitted | Engine switch off | Below 1 V |
| LED (J12-18) - GND (J12-12) | L - W-B | Illuminates when power window operation permitted | Engine switch on (IG) | 10 to 14 V |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| LIN2 (I14-16) - GND (I14-12) | R - W-B | LIN communication line | Always | Pulse generation |
| LIN1 (I14-17) - GND (I14-12) | R - W-B | LIN communication line | Always | Pulse generation |
| UP (I14-20) - GND (I14-12) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| UP (I14-20) - GND (I14-12) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| DOWN (I14-15) - GND (I14-12) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| DOWN (I14-15) - GND (I14-12) | G - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
| LED (I14-18) - GND (I14-12) | L - W-B | Illuminates when power window operation permitted | Engine switch off | Below 1 V |
| LED (I14-18) - GND (I14-12) | L - W-B | Illuminates when power window operation permitted | Engine switch on (IG) | 10 to 14 V |
If the result is not as specified, the master switch may be malfunctioning.
CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
Disconnect the I12*1 or J4*2 switch connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| GND (I12-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| GND (J4-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the I12*1 or J4*2 switch connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| UP (I12-6) - GND (I12-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| DOWN (I12-7) - GND (I12-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| AUTO (I12-8) - GND (I12-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| AUTO (I12-8) - GND (I12-1) | SB - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
| LED (I12-4) - GND (I12-1) | L - W-B | Illuminates when power window operation permitted | Engine switch off | Below 1 V |
| LED (I12-4) - GND (I12-1) | L - W-B | Illuminates when power window operation permitted | Engine switch on (IG) and window lock switch UNLOCK | 10 to 14 V |
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| UP (J4-6) - GND (J4-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| DOWN (J4-7) - GND (J4-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| AUTO (J4-8) - GND (J4-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| AUTO (J4-8) - GND (J4-1) | SB - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
| LED (J4-4) - GND (J4-1) | L - W-B | Illuminates when power window operation permitted | Engine switch off | Below 1 V |
| LED (J4-4) - GND (J4-1) | L - W-B | Illuminates when power window operation permitted | Engine switch on (IG) | 10 to 14 V |
If the result is not as specified, the switch may be malfunctioning.
CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH)
Disconnect the L1 switch connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| GND (L1-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the L1 switch connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| UP (L1-6) - GND (L1-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| DOWN (L1-7) - GND (L1-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| AUTO (L1-8) - GND (L1-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| AUTO (L1-8) - GND (L1-1) | SB - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
| LED (L1-4) - GND (L1-1) | L - W-B | Illuminates when power window operation permitted | Engine switch off | Below 1 V |
| LED (L1-4) - GND (L1-1) | L - W-B | Illuminates when power window operation permitted | ·
Engine switch on (IG) and window lock switch UNLOCK*1 ·
Engine switch on (IG)*2 |
10 to 14 V |
*1: for LHD
*2: for RHD
If the result is not as specified, the switch may be malfunctioning.
CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH)
Disconnect the K1 switch connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| GND (K1-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the K1 switch connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| UP (K1-6) - GND (K1-1) | SB - W-B | Power window UP operation | Engine switch on (IG), driver switch OFF → UP | 10 to 14 V → Below 1 V |
| DOWN (K1-7) - GND (K1-1) | G - W-B | Power window DOWN operation | Engine switch on (IG), driver switch OFF → DOWN | 10 to 14 V → Below 1 V |
| AUTO (K1-8) - GND (K1-1) | SB - W-B | Power window UP operation | Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed | 10 to 14 V → Below 1 V → 10 to 14 V |
| AUTO (K1-8) - GND (K1-1) | SB - W-B | Power window DOWN operation | Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open | 10 to 14 V → Below 1 V → 10 to 14 V |
| LED (K1-4) - GND (K1-1) | L - W-B | Illuminates when power window operation permitted | Engine switch off | Below 1 V |
| LED (K1-4) - GND (K1-1) | L - W-B | Illuminates when power window operation permitted | ·
Engine switch on (IG) and window lock switch UNLOCK*1 ·
Engine switch on (IG)*2 |
10 to 14 V |
*1: for LHD
*2: for RHD
If the result is not as specified, the switch may be malfunctioning.
CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
Disconnect the G59, 4A and 4K ECU connectors.
Measure the voltage and resistance of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| BATB (4K-9) - Body ground | B - Body ground | BATA power supply | Always | 10 to 14 V |
| ACC (4A-26) - Body ground | GR - Body ground | ACC power supply | Engine switch on (ACC) | 10 to 14 V |
| ACC (4A-26) - Body ground | GR - Body ground | ACC power supply | Engine switch off | Below 1 V |
| GND2 (4A-3) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| GND1 (G59-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the G59, 4A and 4K ECU connectors.
Measure the voltage of the connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| DCTY (G57-24) - Body ground | L - Body ground | Driver side door courtesy switch input | Driver side door closed | 10 to 14 V |
| DCTY (G57-24) - Body ground | L - Body ground | Driver side door courtesy switch input | Driver side door open | Below 1 V |
| PCTY (G58-21) - Body ground | L - Body ground | Front passenger side door courtesy switch input | Front passenger side door closed | 10 to 14 V |
| PCTY (G58-21) - Body ground | L - Body ground | Front passenger side door courtesy switch input | Front passenger side door open | Below 1 V |
If the result is not as specified, the ECU may have a malfunction.