Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292216 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)


U188563E01
0.217,1.424 0.933,1.574 0.716,0.149 10 *1: for LHD 0.924,0.837 1.210,0.986 0.286,0.149 10 *1 0.924,1.167 1.210,1.316 0.286,0.149 10 *2 0.585,0.828 0.748,1.009 0.164,0.181 10 J5 0.595,1.166 0.751,1.347 0.156,0.181 10 I5 0.217,1.78 0.984,1.931 0.767,0.151 10 *2: for RHD

a.

Disconnect the J5*1 or I5*2 motor connector.


b.

Measure the voltage and resistance of the wire harness side connector.

for LHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (J5-2) - GND (J5-1) B - W-B Battery power supply Always 10 to 14 V
GND (J5-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (I5-2) - GND (I5-1) B - W-B Battery power supply Always 10 to 14 V
GND (I5-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J5*1 or I5*2 motor connector.


d.

Measure the voltage of the connector.

for LHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
LIN (J5-9) - GND (J5-1) R - W-B LIN communication line Always Pulse generation
UP (J5-10) - GND (J5-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
UP (J5-10) - GND (J5-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
DOWN (J5-7) - GND (J5-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
DOWN (J5-7) - GND (J5-1) G - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V

for RHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
LIN (I5-9) - GND (I5-1) R - W-B LIN communication line Always Pulse generation
UP (I5-10) - GND (I5-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
UP (I5-10) - GND (I5-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
DOWN (I5-7) - GND (I5-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
DOWN (I5-7) - GND (I5-1) G - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V

If the result is not as specified, the motor may be malfunctioning.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side)


U188564E01
0.191,1.409 0.929,1.558 0.738,0.149 10 *1: for LHD 0.924,1.093 1.210,1.242 0.286,0.149 10 *2 0.924,0.773 1.210,0.922 0.286,0.149 10 *1 0.585,1.083 0.748,1.264 0.164,0.181 10 J5 0.595,0.772 0.751,0.953 0.156,0.181 10 I5 0.191,1.761 0.958,1.926 0.767,0.165 10 *2: for RHD

a.

Disconnect the I5*1 or J5*2 motor connector.


b.

Measure the voltage and resistance of the wire harness side connector.

for LHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (I5-2) - GND (I5-1) B - W-B Battery power supply Always 10 to 14 V
GND (I5-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (J5-2) - GND (J5-1) B - W-B Battery power supply Always 10 to 14 V
GND (J5-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the I5*1 or J5*2 motor connector.


d.

Measure the voltage of the connector.

for LHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
LIN (I5-9) - GND (I5-1) R - W-B LIN communication line Always Pulse generation
UP (I5-10) - GND (I5-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
UP (I5-10) - GND (I5-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
DOWN (I5-7) - GND (I5-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
DOWN (I5-7) - GND (I5-1) G - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V

for RHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
LIN (J5-9) - GND (J5-1) R - W-B LIN communication line Always Pulse generation
UP (J5-10) - GND (J5-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
UP (J5-10) - GND (J5-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
DOWN (J5-7) - GND (J5-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
DOWN (J5-7) - GND (J5-1) G - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V

If the result is not as specified, the motor may be malfunctioning.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH)


U185923E02
0.708,1.031 0.885,1.208 0.177,0.177 10 false L2

a.

Disconnect the L2 motor connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (L2-2) - GND (L2-1) L - W-B Battery power supply Always 10 to 14 V
GND (L2-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the L2 motor connector.


d.

Measure the voltage of the connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
LIN (L2-9) - GND (L2-1) R - W-B LIN communication line Always Pulse generation
UP (L2-10) - GND (L2-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
UP (L2-10) - GND (L2-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
DOWN (L2-7) - GND (L2-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
DOWN (L2-7) - GND (L2-1) G - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V

If the result is not as specified, the motor may be malfunctioning.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH)


U185924E02
0.698,1.021 0.896,1.198 0.198,0.177 10 false K2

a.

Disconnect the K2 motor connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (K2-2) - GND (K2-1) L - W-B Battery power supply Always 10 to 14 V
GND (K2-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the K2 motor connector.


d.

Measure the voltage of the connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
LIN (K2-9) - GND (K2-1) R - W-B LIN communication line Always Pulse generation
UP (K2-10) - GND (K2-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
UP (K2-10) - GND (K2-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
DOWN (K2-7) - GND (K2-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
DOWN (K2-7) - GND (K2-1) G - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V

If the result is not as specified, the motor may be malfunctioning.



CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


U188615E01
0.048,1.701 0.799,1.850 0.751,0.149 10 *1: for LHD 0.048,1.933 0.799,2.082 0.751,0.149 10 *2: for RHD 1.264,0.137 1.550,0.286 0.286,0.149 10 *1 2.192,0.147 2.478,0.296 0.286,0.149 10 *2 0.886,0.137 1.133,0.318 0.247,0.181 10 J12 1.839,0.147 2.056,0.328 0.217,0.181 10 I14

a.

Disconnect the J12*1 or I14*2 master switch connector.


b.

Measure the voltage and resistance of the wire harness side connector.

for LHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (J12-11) - GND (J12-12) R - W-B Ignition power supply Engine switch off Below 1 V
B (J12-11) - GND (J12-12) R - W-B Ignition power supply Engine switch on (IG) 10 to 14 V
GND (J12-12) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (I14-11) - GND (I14-12) R - W-B Ignition power supply Engine switch off Below 1 V
B (I14-11) - GND (I14-12) R - W-B Ignition power supply Engine switch on (IG) 10 to 14 V
GND (I14-12) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J12*1 or I14*2 master switch connector.


d.

Measure the voltage of the connector.

for LHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
LIN2 (J12-16) - GND (J12-12) R - W-B LIN communication line Always Pulse generation
LIN1 (J12-17) - GND (J12-12) R - W-B LIN communication line Always Pulse generation
UP (J12-20) - GND (J12-12) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
UP (J12-20) - GND (J12-12) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
DOWN (J12-15) - GND (J12-12) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
DOWN (J12-15) - GND (J12-12) G - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V
LED (J12-18) - GND (J12-12) L - W-B Illuminates when power window operation permitted Engine switch off Below 1 V
LED (J12-18) - GND (J12-12) L - W-B Illuminates when power window operation permitted Engine switch on (IG) 10 to 14 V

for RHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
LIN2 (I14-16) - GND (I14-12) R - W-B LIN communication line Always Pulse generation
LIN1 (I14-17) - GND (I14-12) R - W-B LIN communication line Always Pulse generation
UP (I14-20) - GND (I14-12) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
UP (I14-20) - GND (I14-12) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
DOWN (I14-15) - GND (I14-12) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
DOWN (I14-15) - GND (I14-12) G - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V
LED (I14-18) - GND (I14-12) L - W-B Illuminates when power window operation permitted Engine switch off Below 1 V
LED (I14-18) - GND (I14-12) L - W-B Illuminates when power window operation permitted Engine switch on (IG) 10 to 14 V

If the result is not as specified, the master switch may be malfunctioning.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)


U188616E01
0.116,1.518 0.913,1.667 0.797,0.149 10 *1: for LHD 0.116,1.84 0.913,1.989 0.797,0.149 10 *2: for RHD 0.757,0.887 1.043,1.036 0.286,0.149 10 *1 0.757,1.175 1.043,1.324 0.286,0.149 10 *2 0.417,1.165 0.581,1.347 0.164,0.181 10 J4 0.407,0.881 0.633,1.062 0.225,0.181 10 I12

a.

Disconnect the I12*1 or J4*2 switch connector.


b.

Measure the voltage and resistance of the wire harness side connector.

for LHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND (I12-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND (J4-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the I12*1 or J4*2 switch connector.


d.

Measure the voltage of the connector.

for LHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
UP (I12-6) - GND (I12-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
DOWN (I12-7) - GND (I12-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
AUTO (I12-8) - GND (I12-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
AUTO (I12-8) - GND (I12-1) SB - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V
LED (I12-4) - GND (I12-1) L - W-B Illuminates when power window operation permitted Engine switch off Below 1 V
LED (I12-4) - GND (I12-1) L - W-B Illuminates when power window operation permitted Engine switch on (IG) and window lock switch UNLOCK 10 to 14 V

for RHD
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
UP (J4-6) - GND (J4-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
DOWN (J4-7) - GND (J4-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
AUTO (J4-8) - GND (J4-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
AUTO (J4-8) - GND (J4-1) SB - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V
LED (J4-4) - GND (J4-1) L - W-B Illuminates when power window operation permitted Engine switch off Below 1 V
LED (J4-4) - GND (J4-1) L - W-B Illuminates when power window operation permitted Engine switch on (IG) 10 to 14 V

If the result is not as specified, the switch may be malfunctioning.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH)


U185945E02
0.75,1.115 0.938,1.292 0.188,0.177 10 false L1

a.

Disconnect the L1 switch connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND (L1-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the L1 switch connector.


d.

Measure the voltage of the connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
UP (L1-6) - GND (L1-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
DOWN (L1-7) - GND (L1-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
AUTO (L1-8) - GND (L1-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
AUTO (L1-8) - GND (L1-1) SB - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V
LED (L1-4) - GND (L1-1) L - W-B Illuminates when power window operation permitted Engine switch off Below 1 V
LED (L1-4) - GND (L1-1) L - W-B Illuminates when power window operation permitted
·

Engine switch on (IG) and window lock switch UNLOCK*1

·

Engine switch on (IG)*2


10 to 14 V

*1: for LHD

*2: for RHD


If the result is not as specified, the switch may be malfunctioning.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH)


U185946E02
0.75,1.104 0.938,1.281 0.188,0.177 10 false K1

a.

Disconnect the K1 switch connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
GND (K1-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the K1 switch connector.


d.

Measure the voltage of the connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
UP (K1-6) - GND (K1-1) SB - W-B Power window UP operation Engine switch on (IG), driver switch OFF → UP 10 to 14 V → Below 1 V
DOWN (K1-7) - GND (K1-1) G - W-B Power window DOWN operation Engine switch on (IG), driver switch OFF → DOWN 10 to 14 V → Below 1 V
AUTO (K1-8) - GND (K1-1) SB - W-B Power window UP operation Engine switch on (IG), door glass fully open → power window AUTO UP operation → door glass fully closed 10 to 14 V → Below 1 V → 10 to 14 V
AUTO (K1-8) - GND (K1-1) SB - W-B Power window DOWN operation Engine switch on (IG), door glass fully closed → power window AUTO DOWN operation → door glass fully open 10 to 14 V → Below 1 V → 10 to 14 V
LED (K1-4) - GND (K1-1) L - W-B Illuminates when power window operation permitted Engine switch off Below 1 V
LED (K1-4) - GND (K1-1) L - W-B Illuminates when power window operation permitted
·

Engine switch on (IG) and window lock switch UNLOCK*1

·

Engine switch on (IG)*2


10 to 14 V

*1: for LHD

*2: for RHD


If the result is not as specified, the switch may be malfunctioning.



CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U185956E02
1.323,1.604 1.604,1.771 0.281,0.167 10 false 4A 1.74,4.656 2.021,4.823 0.281,0.167 10 false 4A 5.677,1.542 5.958,1.708 0.281,0.167 10 false 4G 5.677,2.438 5.958,2.604 0.281,0.167 10 false 4K 5.688,2.885 5.969,3.052 0.281,0.167 10 false 4L 5.677,3.208 5.958,3.375 0.281,0.167 10 false 4M 6.135,3.188 6.417,3.354 0.281,0.167 10 false 4N 6.083,2.802 6.469,2.969 0.385,0.167 10 false G60 6.073,2.5 6.458,2.667 0.385,0.167 10 false G59 6.083,2.063 6.469,2.229 0.385,0.167 10 false G58 6.073,1.542 6.458,1.708 0.385,0.167 10 false G57 1.344,2.854 1.625,3.021 0.281,0.167 10 false 4D 5.26,4.667 5.542,4.833 0.281,0.167 10 false 4D 0.646,6.094 0.927,6.26 0.281,0.167 10 false 4M 1.177,7.542 1.458,7.708 0.281,0.167 10 false 4N 2.76,7.344 3.156,7.51 0.396,0.167 10 false G60 3.396,7.344 3.792,7.51 0.396,0.167 10 false G59 4.406,7.344 4.802,7.51 0.396,0.167 10 false G58 5.552,7.344 5.948,7.51 0.396,0.167 10 false G57 1.813,6.083 2.094,6.25 0.281,0.167 10 false 4L 3.146,6.031 3.427,6.198 0.281,0.167 10 false 4K 5.365,5.958 5.646,6.125 0.281,0.167 10 false 4G

a.

Disconnect the G59, 4A and 4K ECU connectors.


b.

Measure the voltage and resistance of the wire harness side connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
BATB (4K-9) - Body ground B - Body ground BATA power supply Always 10 to 14 V
ACC (4A-26) - Body ground GR - Body ground ACC power supply Engine switch on (ACC) 10 to 14 V
ACC (4A-26) - Body ground GR - Body ground ACC power supply Engine switch off Below 1 V
GND2 (4A-3) - Body ground W-B - Body ground Ground Always Below 1 Ω
GND1 (G59-1) - Body ground W-B - Body ground Ground Always Below 1 Ω

HINT:

If the result is not as specified, there may be a malfunction in the wire harness.



c.

Reconnect the G59, 4A and 4K ECU connectors.


d.

Measure the voltage of the connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
DCTY (G57-24) - Body ground L - Body ground Driver side door courtesy switch input Driver side door closed 10 to 14 V
DCTY (G57-24) - Body ground L - Body ground Driver side door courtesy switch input Driver side door open Below 1 V
PCTY (G58-21) - Body ground L - Body ground Front passenger side door courtesy switch input Front passenger side door closed 10 to 14 V
PCTY (G58-21) - Body ground L - Body ground Front passenger side door courtesy switch input Front passenger side door open Below 1 V
UL2 (4A-25) - Body ground W - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
UL2 (4A-25) - Body ground W - Body ground Driver door key-linked unlock input Driver door key cylinder off Pulse generation
L2 (4A-11) - Body ground R - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
L2 (4A-11) - Body ground R - Body ground Driver door key-linked lock input Driver door key cylinder off Pulse generation

HINT:

If the result is not as specified, the ECU may have a malfunction.