Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292216 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Key-off Operation Function Operates even if Operating Conditions are not Satisfied  


DESCRIPTION

When all doors are closed, each power window regulator motor can control its power window operation for approximately 45 seconds after the ignition switch is turned from on (IG) to off by receiving operation permission signals from the main body ECU.

However, when approximately 45 seconds have elapsed, or the driver side door or front passenger side door is opened within approximately 45 seconds of the ignition switch being turned off, the power window regulator motor stops operating.

During AUTO function operation, the window operation will continue until complete even if 45 seconds have passed or a door is opened.

CAUTION:

The power window control system prohibits the AUTO UP / DOWN function when the jam protection function malfunctions. Therefore, troubleshoot the power window control system after confirming that no diagnostic codes are displayed.


WIRING DIAGRAM

B148312E03
3.319,5.479 4.363,5.622 1.044,0.143 10 Main Body ECU 3.394,3.517 3.955,3.660 0.560,0.143 10 DCTY*1 0.069,6.372 1.666,6.515 1.597,0.143 10 *1: for LHD 0.069,6.61 1.666,6.753 1.597,0.143 10 *2: for RHD 3.394,3.685 3.955,3.828 0.560,0.143 10 PCTY*2 4.01,4.126 4.343,4.269 0.332,0.143 10 LIN2 4.43,4.138 4.762,4.281 0.332,0.143 10 G59 4.477,3.96 4.810,4.103 0.332,0.143 10 10 2.861,3.587 3.284,3.730 0.423,0.143 10 G58*2 2.925,3.409 3.257,3.552 0.332,0.143 10 21*2 2.861,4.833 3.284,4.977 0.423,0.143 10 G57*2 2.925,4.656 3.257,4.799 0.332,0.143 10 24*2 2.392,3.587 2.815,3.730 0.423,0.143 10 G57*1 2.456,3.409 2.788,3.552 0.332,0.143 10 24*1 2.399,4.833 2.822,4.977 0.423,0.143 10 G58*1 2.463,4.656 2.795,4.799 0.332,0.143 10 21*1 5.384,1.025 5.492,1.168 0.108,0.143 10 9 5.608,0.875 6.168,1.018 0.560,0.143 10 LIN 5.327,3.771 5.534,3.914 0.208,0.143 10 16 5.608,3.621 6.168,3.764 0.560,0.143 10 LIN2 5.327,4.283 5.534,4.426 0.208,0.143 10 17 5.608,4.134 6.168,4.277 0.560,0.143 10 LIN1 3.394,4.772 3.955,4.915 0.560,0.143 10 PCTY*1 3.394,4.921 3.955,5.064 0.560,0.143 10 DCTY*2 4.963,1.668 7.015,1.811 2.052,0.143 10 J5*1, I5*2 4.963,1.818 7.015,2.148 2.052,0.331 10 Power Window Regulator Motor (for Driver Side) 4.963,5.442 7.015,5.585 2.052,0.143 10 J12*1, I14*2 4.963,5.591 7.015,5.747 2.052,0.156 10 Multiplex Network Master Switch 1.001,3.888 1.360,4.031 0.359,0.143 10 M5 1.001,4.037 2.326,4.343 1.326,0.306 10 Front Door Courtesy Light Switch LH 1.001,5.12 1.360,5.264 0.359,0.143 10 N1 1.001,5.27 2.326,5.588 1.326,0.318 10 Front Door Courtesy Light Switch RH 2.002,4.721 2.146,4.864 0.144,0.143 10 1 1.981,3.502 2.125,3.645 0.144,0.143 10 1

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (LIN COMMUNICATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body / Body ECU / Data List.


d.

Read the display on the tester.

Main body ECU
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Communication D-Door Motor Connection status between power window regulator motor (for driver side) and main body ECU / OK or STOP OK: Connection
Stop: No connection
-

OK:

OK is displayed on the intelligent tester screen.




OK

2.CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF

NG

GO TO DTC B2321

2.CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF
a.

Check the power window operation function after the ignition switch is turned off.

Result
Result Proceed to
Driver side door is opened within 45 seconds but power window can still operate A
45 seconds pass and the power windows can still operate B



A

3.CHECK OPERATION OF FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

B

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (APPLICABLE LOCATION)
3.CHECK OPERATION OF FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
a.

When the map light switch is in the DOOR position, open the driver side door and check that the map light illuminates.

OK:

Map light illuminates.




OK

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (APPLICABLE LOCATION)

NG

GO TO LIGHTING SYSTEM

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (APPLICABLE LOCATION)
a.

Temporarily replace the power window regulator motor with a new or normally functioning one.


b.

Check that the key-off operation function operates normally.

OK:

Key-off operation function operates normally.




OK

END

NG

REPLACE MAIN BODY ECU