Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292216 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor is driven by operating the power window switch. The power window regulator motor has motor, regulator and ECU functions.

This DTC is output when the ECU built into the regulator motor determines that the power window switch is stuck.

HINT:

This DTC may occur for all the windows.


NOTICE:
·

When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.

·

After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:

(a)

Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.

(b)

Open the power window by fully pushing down the switch.




Multiplex network master switch
DTC No. DTC Detection Condition Trouble Area
B2312 Multiplex network master switch stuck
·

Multiplex network master switch

·

Multiplex network master switch held in same position for more than 20 seconds



Power window regulator motor (for Driver side)
DTC No. DTC Detection Condition Trouble Area
B2312 Multiplex network master switch stuck
·

Multiplex network master switch

·

Power window regulator motor

·

Wire harness

·

Multiplex network master switch held in same position for more than 20 seconds



Power window regulator motor (for Front passenger side)
DTC No. DTC Detection Condition Trouble Area
B2312 Power window regulator switch stuck
·

Power window regulator switch

·

Power window regulator motor

·

Wire harness

·

Power window regulator switch held in same position for more than 20 seconds



Power window regulator motor (for Rear LH)
DTC No. DTC Detection Condition Trouble Area
B2312 Power window regulator switch stuck
·

Power window regulator switch

·

Power window regulator motor

·

Wire harness

·

Power window regulator switch held in same position for more than 20 seconds



Power window regulator motor (for Rear RH)
DTC No. DTC Detection Condition Trouble Area
B2312 Power window regulator switch stuck
·

Power window regulator switch

·

Power window regulator motor

·

Wire harness

·

Power window regulator switch held in same position for more than 20 seconds



WIRING DIAGRAM

B144444E05
0.978,2.997 3.023,3.153 2.045,0.156 10 J12*1, I14*2 0.1,1.68 0.941,1.836 0.841,0.156 10 from Battery 2.996,0.503 3.837,0.659 0.841,0.156 10 from Battery 5.611,0.503 6.452,0.659 0.841,0.156 10 B 5.611,0.961 6.452,1.117 0.841,0.156 10 UP 5.611,1.419 6.452,1.574 0.841,0.156 10 DOWN 5.611,1.876 6.452,2.032 0.841,0.156 10 LIN 5.611,2.334 6.452,2.490 0.841,0.156 10 GND 1.539,0.543 2.380,0.699 0.841,0.156 10 B 0.558,0.695 1.138,0.851 0.580,0.156 10 ECU-B2 0.058,0.031 1.386,0.187 1.328,0.156 10 for Driver Side: 4.403,0.659 5.085,0.815 0.682,0.156 10 P/W FL*1 4.403,0.827 5.069,0.983 0.666,0.156 10 P/W FR*2 2.169,0.961 2.429,1.117 0.260,0.156 10 UP 2.001,1.419 2.483,1.574 0.482,0.156 10 DOWN 2.113,1.876 2.457,2.032 0.343,0.156 10 LIN2 2.107,2.334 2.478,2.490 0.371,0.156 10 GND 5.368,0.657 5.496,0.813 0.128,0.156 10 2 5.307,1.115 5.509,1.271 0.202,0.156 10 10 5.368,1.572 5.496,1.728 0.128,0.156 10 7 5.368,2.03 5.496,2.186 0.128,0.156 10 9 5.368,2.488 5.496,2.644 0.128,0.156 10 1 1.23,0.657 1.417,0.813 0.187,0.156 10 11 2.593,1.115 2.795,1.271 0.202,0.156 10 20 2.593,1.572 2.776,1.728 0.183,0.156 10 15 2.593,2.03 2.780,2.186 0.187,0.156 10 16 2.593,2.488 2.780,2.644 0.187,0.156 10 12 0.978,3.184 3.023,3.340 2.045,0.156 10 Multiplex Network Master Switch 4.901,2.997 6.946,3.153 2.045,0.156 10 J5*1, I5*2 0.061,3.256 0.837,3.419 0.776,0.163 10 *1: for LHD 4.901,3.184 6.946,3.340 2.045,0.156 10 Power Window Regulator Motor 0.061,3.51 0.800,3.673 0.739,0.163 10 *2: for RHD

B144443E11
0.792,2.979 2.833,3.135 2.042,0.156 10 false I12*1, J4*2 2.573,0.51 3.448,0.688 0.875,0.177 10 false from Battery 0.104,0.073 2.198,0.229 2.094,0.156 10 false for Front Passenger Side: 5.594,0.531 6.438,0.688 0.844,0.156 10 false B 5.594,0.99 6.438,1.146 0.844,0.156 10 false UP 5.594,1.438 6.438,1.594 0.844,0.156 10 false DOWN 5.583,1.896 6.427,2.052 0.844,0.156 10 false AUTO 5.583,2.323 6.427,2.479 0.844,0.156 10 false GND 3.979,0.656 4.656,0.813 0.677,0.156 10 false P/W FR*1 3.979,0.823 4.646,0.979 0.667,0.156 10 false P/W FL*2 1.469,0.99 1.729,1.146 0.26,0.156 10 false UP 1.24,1.438 1.719,1.594 0.479,0.156 10 false DOWN 1.302,1.906 1.729,2.063 0.427,0.156 10 false AUTO 1.375,2.313 1.75,2.469 0.375,0.156 10 false GND 5.375,0.635 5.5,0.792 0.125,0.156 10 false 2 5.313,1.115 5.51,1.271 0.198,0.156 10 false 10 5.344,1.563 5.469,1.719 0.125,0.156 10 false 7 5.365,2.031 5.49,2.188 0.125,0.156 10 false 4 5.375,2.479 5.5,2.635 0.125,0.156 10 false 1 1.833,1.094 2.031,1.25 0.198,0.156 10 false 6 1.844,1.563 2.031,1.719 0.188,0.156 10 false 7 1.823,2.021 2.01,2.177 0.188,0.156 10 false 8 1.844,2.448 2.031,2.604 0.188,0.156 10 false 1 0.771,3.146 2.813,3.302 2.042,0.156 10 false Power Window Regulator Switch 5.115,2.979 7.156,3.135 2.042,0.156 10 false I5*1, J5*2 0.052,3.271 0.792,3.427 0.74,0.156 10 false *1: for LHD 5.115,3.146 7.156,3.302 2.042,0.156 10 false Power Window Regulator Motor 0.063,3.531 0.802,3.677 0.74,0.146 10 false *2: for RHD

B144443E02
0.553,3.002 2.598,3.158 2.045,0.156 10 L1 2.57,0.508 3.411,0.664 0.841,0.156 10 from Battery 0.05,0.032 0.932,0.180 0.882,0.149 10 for Rear LH: 5.597,0.508 6.438,0.664 0.841,0.156 10 B 5.597,0.966 6.438,1.122 0.841,0.156 10 UP 5.597,1.424 6.438,1.580 0.841,0.156 10 DOWN 5.597,1.881 6.438,2.037 0.841,0.156 10 AUTO 5.597,2.339 6.438,2.495 0.841,0.156 10 GND 3.978,0.664 4.660,0.820 0.682,0.156 10 P/W RL 1.427,0.966 1.687,1.122 0.260,0.156 10 UP 1.259,1.424 1.741,1.580 0.482,0.156 10 DOWN 1.291,1.881 1.713,2.037 0.422,0.156 10 AUTO 1.365,2.339 1.736,2.495 0.371,0.156 10 GND 5.354,0.662 5.482,0.818 0.128,0.156 10 2 5.293,1.12 5.495,1.276 0.202,0.156 10 10 5.354,1.577 5.482,1.733 0.128,0.156 10 7 5.354,2.035 5.482,2.191 0.128,0.156 10 4 5.354,2.493 5.482,2.649 0.128,0.156 10 1 1.85,1.12 2.052,1.276 0.202,0.156 10 6 1.85,1.577 2.033,1.733 0.183,0.156 10 7 1.85,2.035 2.037,2.191 0.187,0.156 10 8 1.85,2.493 2.037,2.649 0.187,0.156 10 1 0.553,3.189 2.598,3.345 2.045,0.156 10 Power Window Regulator Switch 4.887,3.002 6.932,3.158 2.045,0.156 10 L2 4.887,3.189 6.932,3.345 2.045,0.156 10 Power Window Regulator Motor

B144443E03
0.553,3.002 2.598,3.158 2.045,0.156 10 K1 2.57,0.508 3.411,0.664 0.841,0.156 10 from Battery 0.05,0.03 2.022,0.171 1.972,0.141 10 for Rear RH: 5.597,0.508 6.438,0.664 0.841,0.156 10 B 5.597,0.966 6.438,1.122 0.841,0.156 10 UP 5.597,1.424 6.438,1.580 0.841,0.156 10 DOWN 5.597,1.881 6.438,2.037 0.841,0.156 10 AUTO 5.597,2.339 6.438,2.495 0.841,0.156 10 GND 3.978,0.664 4.660,0.820 0.682,0.156 10 P/W RR 1.427,0.966 1.687,1.122 0.260,0.156 10 UP 1.259,1.424 1.741,1.580 0.482,0.156 10 DOWN 1.291,1.881 1.713,2.037 0.422,0.156 10 AUTO 1.365,2.339 1.736,2.495 0.371,0.156 10 GND 5.354,0.662 5.482,0.818 0.128,0.156 10 2 5.293,1.12 5.495,1.276 0.202,0.156 10 10 5.354,1.577 5.482,1.733 0.128,0.156 10 7 5.354,2.035 5.482,2.191 0.128,0.156 10 4 5.354,2.493 5.482,2.649 0.128,0.156 10 1 1.85,1.12 2.052,1.276 0.202,0.156 10 6 1.85,1.577 2.033,1.733 0.183,0.156 10 7 1.85,2.035 2.037,2.191 0.187,0.156 10 8 1.85,2.493 2.037,2.649 0.187,0.156 10 1 0.553,3.189 2.598,3.345 2.045,0.156 10 Power Window Regulator Switch 4.887,3.002 6.932,3.158 2.045,0.156 10 K2 4.887,3.189 6.932,3.345 2.045,0.156 10 Power Window Regulator Motor

PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Result
Result Proceed to
DTC output from multiplex network master switch A
DTC output from driver side motor B
DTC output from front passenger side motor C
DTC output from rear LH motor D
DTC output from rear RH motor E



A

2.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)

B

3.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)

C

5.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)

D

8.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)

E

11.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)
2.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body / Master Switch / Data List.


d.

Read the display on the tester.

Multiplex network master switch
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window AUTO UP / DOWN switch signal / ON or OFF ON: Driver side power window switch operates (AUTO operation)
OFF: Driver side power window switch does not operate
-
P Door P/W Auto SW Front passenger side power window AUTO UP / DOWN switch signal / ON or OFF ON: Front passenger side power window switch operates (AUTO operation)
OFF: Front passenger side power window switch does not operate
-
RL Door P/W Auto SW Rear LH power window AUTO UP / DOWN switch signal / ON or OFF ON: Rear LH power window switch operates (AUTO operation)
OFF: Rear LH power window switch does not operate
-
RR Door P/W Auto SW Rear RH power window AUTO UP / DOWN switch signal / ON or OFF ON: Rear RH power window switch operates (AUTO operation)
OFF: Rear RH power window switch does not operate
-
P Door P/W Up SW Front passenger side power window MANUAL UP switch signal / ON or OFF ON: Front passenger side power window switch operates (MANUAL UP operation)
OFF: Front passenger side power window switch does not operate
-
RL Door P/W Up SW Rear LH power window MANUAL UP switch signal / ON or OFF ON: Rear LH power window switch operates (MANUAL UP operation)
OFF: Rear LH power window switch does not operate
-
RR Door P/W Up SW Rear RH power window MANUAL UP switch signal / ON or OFF ON: Rear RH power window switch operates (MANUAL UP operation)
OFF: Rear RH power window switch does not operate
-
P Door P/W Down SW Front passenger side power window MANUAL DOWN switch signal / ON or OFF ON: Front passenger side power window switch operates (MANUAL DOWN operation)
OFF: Front passenger side power window switch does not operate
-
RL Door P/W Down SW Rear LH power window MANUAL DOWN switch signal / ON or OFF ON: Rear LH power window switch operates (MANUAL DOWN operation)
OFF: Rear LH power window switch does not operate
-
RR Door P/W Down SW Rear RH power window MANUAL DOWN switch signal / ON or OFF ON: Rear RH power window switch operates (MANUAL DOWN operation)
OFF: Rear RH power window switch does not operate
-
Window Lock Switch Status Window lock switch signal / ON or OFF ON: Window lock switch LOCK position
OFF: Window lock switch UNLOCK position
-

OK:

Tester display changes normally when multiplex network master switch is operated.




OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

3.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body / D-Door Motor / Data List.


d.

Read the display on the tester.

Driver side power window regulator motor (Power window ECU)
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window AUTO UP / DOWN switch signal / ON or OFF ON: Driver side power window switch operates (AUTO operation)
OFF: Driver side power window switch does not operate
-
D Door P/W Up SW Driver side power window MANUAL UP switch signal / ON or OFF ON: Driver side power window switch operates (MANUAL UP operation)
OFF: Driver side power window switch does not operate
-
D Door P/W Down SW Driver side power window MANUAL DOWN switch signal / ON or OFF ON: Driver side power window switch operates (MANUAL DOWN operation)
OFF: Driver side power window switch does not operate
-

OK:

Tester display changes normally when multiplex network master switch is operated.




NG

4.CHECK WIRE HARNESS (MASTER SWITCH - POWER WINDOW MOTOR)

OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

4.CHECK WIRE HARNESS (MASTER SWITCH - POWER WINDOW MOTOR)
a.

Disconnect the J12*1 or I14*2 switch connector.


b.

Disconnect the J5*1 or I5*2 motor connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LHD
Tester Connection Specified Condition
J12-20 (UP) - J5-10 (UP) Below 1 Ω
J12-15 (DOWN) - J5-7 (DOWN) Below 1 Ω
J12-20 (UP) or J5-10 (UP) - Body ground 10 kΩ or higher
J12-15 (DOWN) or J5-7 (DOWN) - Body ground 10 kΩ or higher

for RHD
Tester Connection Specified Condition
I14-20 (UP) - I5-10 (UP) Below 1 Ω
I14-15 (DOWN) - I5-7 (DOWN) Below 1 Ω
I14-20 (UP) or I5-10 (UP) - Body ground 10 kΩ or higher
I14-15 (DOWN) or I5-7 (DOWN) - Body ground 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body / P-Door Motor / Data List.


d.

Read the display on the tester.

Front passenger side power window regulator motor (Power window ECU)
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger side power window AUTO UP / DOWN switch signal / ON or OFF ON: Front passenger side power window switch operates (AUTO operation)
OFF: Front passenger side power window switch does not operate
-
P Door P/W Up SW Front passenger side power window MANUAL UP switch signal / ON or OFF ON: Front passenger side power window switch operates (MANUAL UP operation)
OFF: Front passenger side power window switch does not operate
-
P Door P/W Down SW Front passenger side power window MANUAL DOWN switch signal / ON or OFF ON: Front passenger side power window switch operates (MANUAL DOWN operation)
OFF: Front passenger side power window switch does not operate
-

OK:

Tester display changes normally when front passenger side power window switch is operated.




NG

6.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

6.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
a.
B129574E04
2.492,1.078 2.842,1.234 0.350,0.156 10 GND 2.19,1.892 2.409,2.048 0.218,0.156 10 UP 0.979,1.892 1.482,2.048 0.503,0.156 10 DOWN 0.458,1.293 0.898,1.449 0.441,0.156 10 AUTO 2.061,1.157 2.448,1.157 false 1.001,1.386 1.387,1.386 false 1.617,1.446 1.269,1.86 false 1.846,1.446 2.195,1.86 false

Remove the switch.


b.

Measure the resistance of the switch when the switch is operated.

Standard resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual UP operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual DOWN operation Below 1 Ω
8 (AUTO) - 1 (GND) AUTO UP / DOWN operation Below 1 Ω




OK

7.CHECK WIRE HARNESS (FRONT PASSENGER SIDE SWITCH - FRONT PASSENGER SIDE MOTOR)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

7.CHECK WIRE HARNESS (FRONT PASSENGER SIDE SWITCH - FRONT PASSENGER SIDE MOTOR)
a.

Disconnect the I12*1 or J4*2 switch connector.


b.

Disconnect the I5*1 or J5*2 motor connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LHD
Tester Connection Specified Condition
I12-6 (UP) - I5-10 (UP) Below 1 Ω
I12-7 (DOWN) - I5-7 (DOWN) Below 1 Ω
I12-8 (AUTO) - I5-4 (AUTO) Below 1 Ω
I12-6 (UP) or I5-10 (UP) - Body ground 10 kΩ or higher
I12-7 (DOWN) or I5-7 (DOWN) - Body ground 10 kΩ or higher
I12-8 (AUTO) or I5-4 (AUTO) - Body ground 10 kΩ or higher

for RHD
Tester Connection Specified Condition
J4-6 (UP) - J5-10 (UP) Below 1 Ω
J4-7 (DOWN) - J5-7 (DOWN) Below 1 Ω
J4-8 (AUTO) - J5-4 (AUTO) Below 1 Ω
J4-6 (UP) or J5-10 (UP) - Body ground 10 kΩ or higher
J4-7 (DOWN) or J5-7 (DOWN) - Body ground 10 kΩ or higher
J4-8 (AUTO) or J5-4 (AUTO) - Body ground 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body / RL-Door Motor / Data List.


d.

Read the display on the tester.

Rear LH power window regulator motor (Power window ECU)
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear LH power window AUTO UP / DOWN switch signal / ON or OFF ON: Rear LH power window switch operates (AUTO operation)
OFF: Rear LH power window switch does not operate
-
RL Door P/W Up SW Rear LH power window MANUAL UP switch signal / ON or OFF ON: Rear LH power window switch operates (MANUAL UP operation)
OFF: Rear LH power window switch does not operate
-
RL Door P/W Down SW Rear LH power window MANUAL DOWN switch signal / ON or OFF ON: Rear LH power window switch operates (MANUAL DOWN operation)
OFF: Rear LH power window switch does not operate
-

OK:

Tester display changes normally when rear LH power window switch is operated.




NG

9.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH)

OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

9.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH)
a.
B129574E04
2.492,1.078 2.842,1.234 0.350,0.156 10 GND 2.19,1.892 2.409,2.048 0.218,0.156 10 UP 0.979,1.892 1.482,2.048 0.503,0.156 10 DOWN 0.458,1.293 0.898,1.449 0.441,0.156 10 AUTO 2.061,1.157 2.448,1.157 false 1.001,1.386 1.387,1.386 false 1.617,1.446 1.269,1.86 false 1.846,1.446 2.195,1.86 false

Remove the switch.


b.

Measure the resistance of the switch when the switch is operated.

Standard resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual UP operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual DOWN operation Below 1 Ω
8 (AUTO) - 1 (GND) AUTO UP / DOWN operation Below 1 Ω




OK

10.CHECK WIRE HARNESS (REAR LH SWITCH - REAR LH MOTOR)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH)

10.CHECK WIRE HARNESS (REAR LH SWITCH - REAR LH MOTOR)
a.

Disconnect the L1 switch connector.


b.

Disconnect the L2 motor connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
L1-6 (UP) - L2-10 (UP) Below 1 Ω
L1-7 (DOWN) - L2-7 (DOWN) Below 1 Ω
L1-8 (AUTO) - L2-4 (AUTO) Below 1 Ω
L1-6 (UP) or L2-10 (UP) - Body ground 10 kΩ or higher
L1-7 (DOWN) or L2-7 (DOWN) - Body ground 10 kΩ or higher
L1-8 (AUTO) or L2-4 (AUTO) - Body ground 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body / RR-Door Motor / Data List.


d.

Read the display on the tester.

Rear RH power window regulator motor (Power window ECU)
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear RH power window AUTO UP / DOWN switch signal / ON or OFF ON: Rear RH power window switch operates (AUTO operation)
OFF: Rear RH power window switch does not operate
-
RR Door P/W Up SW Rear RH power window MANUAL UP switch signal / ON or OFF ON: Rear RH power window switch operates (MANUAL UP operation)
OFF: Rear RH power window switch does not operate
-
RR Door P/W Down SW Rear RH power window MANUAL DOWN switch signal / ON or OFF ON: Rear RH power window switch operates (MANUAL DOWN operation)
OFF: Rear RH power window switch does not operate
-

OK:

Tester display changes normally when rear RH power window switch is operated.




NG

12.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH)

OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

12.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH)
a.
B129574E04
2.492,1.078 2.842,1.234 0.350,0.156 10 GND 2.19,1.892 2.409,2.048 0.218,0.156 10 UP 0.979,1.892 1.482,2.048 0.503,0.156 10 DOWN 0.458,1.293 0.898,1.449 0.441,0.156 10 AUTO 2.061,1.157 2.448,1.157 false 1.001,1.386 1.387,1.386 false 1.617,1.446 1.269,1.86 false 1.846,1.446 2.195,1.86 false

Remove the switch.


b.

Measure the resistance of the switch when the switch is operated.

Standard resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual UP operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual DOWN operation Below 1 Ω
8 (AUTO) - 1 (GND) AUTO UP / DOWN operation Below 1 Ω




OK

13.CHECK WIRE HARNESS (REAR RH SWITCH - REAR RH MOTOR)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH)

13.CHECK WIRE HARNESS (REAR RH SWITCH - REAR RH MOTOR)
a.

Disconnect the K1 switch connector.


b.

Disconnect the K2 motor connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
K1-6 (UP) - K2-10 (UP) Below 1 Ω
K1-7 (DOWN) - K2-7 (DOWN) Below 1 Ω
K1-8 (AUTO) - K2-4 (AUTO) Below 1 Ω
K1-6 (UP) or K2-10 (UP) - Body ground 10 kΩ or higher
K1-7 (DOWN) or K2-7 (DOWN) - Body ground 10 kΩ or higher
K1-8 (AUTO) or K2-4 (AUTO) - Body ground 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR