The power window regulator motor is driven by operating the power window switch. The power window regulator motor has motor, regulator and ECU functions.
This DTC is output when the power window regulator motor assembly has a malfunction, or the ECU built into the regulator motor assembly determines that the fully closed window position has deviated approximately 20 mm (0.79 in.) or more from the normal position.
This DTC may occur for all the windows.
When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.
Open the power window by fully pushing down the switch.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | When either condition below is met: (a)
Power window regulator motor malfunctions (b)
When ECU in power window regulator motor determines that fully closed window position has deviated approx. 20 mm (0.79 in.) or more from normal position |
·
Battery disconnection when ignition switch on (IG) ·
Power window regulator motor ·
Incorrect installation of power window components ·
Overheated power window regulator motor |
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | When either condition below is met: (a)
Power window regulator motor malfunctions (b)
When ECU in power window regulator motor determines that fully closed window position has deviated approx. 20 mm (0.79 in.) or more from normal position |
·
Battery disconnection when ignition switch on (IG) ·
Power window regulator motor ·
Incorrect installation of power window components ·
Overheated power window regulator motor |
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | When either condition below is met: (a)
Power window regulator motor malfunctions (b)
When ECU in power window regulator motor determines that fully closed window position has deviated approx. 20 mm (0.79 in.) or more from normal position |
·
Battery disconnection when ignition switch on (IG) ·
Power window regulator motor ·
Incorrect installation of power window components ·
Overheated power window regulator motor |
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | When either condition below is met: (a)
Power window regulator motor malfunctions (b)
When ECU in power window regulator motor determines that fully closed window position has deviated approx. 20 mm (0.79 in.) or more from normal position |
·
Battery disconnection when ignition switch on (IG) ·
Power window regulator motor ·
Incorrect installation of power window components ·
Overheated power window regulator motor |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Perform the Active Test according to the prompts displayed on the tester.
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
| Item | Test Details (Default) | Diagnostic Note |
|---|---|---|
| Power window | UP / OFF (OFF) | - |
| Power window | DOWN / OFF (OFF) | - |
| Item | Test Details (Default) | Diagnostic Note |
|---|---|---|
| Power window | UP / OFF (OFF) | - |
| Power window | DOWN / OFF (OFF) | - |
| Item | Test Details (Default) | Diagnostic Note |
|---|---|---|
| Power window | UP / OFF (OFF) | - |
| Power window | DOWN / OFF (OFF) | - |
| Item | Test Details (Default) | Diagnostic Note |
|---|---|---|
| Power window | UP / OFF (OFF) | - |
| Power window | DOWN / OFF (OFF) | - |
Power window operates normally.
OK
NG
Initialize the power window regulator motor assembly (see page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Check that the power window operates normally by opening and closing the window.
Power window operates normally.
OK
NG
Check that the power window components are installed correctly.
Power window components are installed correctly.
When the power window components are installed correctly, the problem has been caused by battery disconnection while the ignition switch is on (IG), improper installation of the power window components or the motor being overheated.
OK
NG