Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292220 POWER WINDOW REGULATOR MOTOR G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR  INSPECTION  


PROCEDURE

Hide 85720C 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front LH)

a.
B145465E02
1.479,3.635 0.76,3.635 false 2.5,3.635 1.792,3.635 false 1.396,4.01 0.802,4.01 false 2.448,4.01 1.885,4.01 false 1.615,0.01 2.375,0.177 0.76,0.167 10 false Motor Gear 1.958,2.5 2.625,2.667 0.667,0.167 10 false Clockwise 0.563,3.542 0.688,3.708 0.125,0.167 10 false B 2.583,3.542 2.948,3.708 0.365,0.167 10 false GND 0.531,3.927 0.771,4.094 0.24,0.167 10 false UP 2.542,3.927 3.031,4.094 0.49,0.167 10 false DOWN 2.063,1.177 3.167,1.344 1.104,0.167 10 false Counterclockwise

Apply positive (+) battery voltage to connector terminal 2.

CAUTION:

Do not apply positive (+) battery voltage to any terminals, except terminal 2, to avoid damaging the pulse sensor inside the motor.



b.

Apply negative (-) battery voltage to connector terminals 1 and 7 / 10.


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 7
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 10
Motor gear rotates clockwise


If the result is not as specified, replace the regulator motor assembly.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85710D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front RH)

a.
B145466E03
1.573,3.417 0.865,3.417 false 2.604,3.417 1.885,3.417 false 1.479,3.792 0.896,3.792 false 2.563,3.792 1.99,3.792 false 0.813,0.031 1.573,0.198 0.76,0.167 10 false Motor Gear 0.385,1.448 1.052,1.615 0.667,0.167 10 false Clockwise 0.656,3.323 0.781,3.49 0.125,0.167 10 false B 2.677,3.323 3.042,3.49 0.365,0.167 10 false GND 0.635,3.719 0.875,3.885 0.24,0.167 10 false UP 2.625,3.719 3.115,3.885 0.49,0.167 10 false DOWN 0.938,2.365 2.115,2.531 1.177,0.167 10 false Counterclockwise

Apply positive (+) battery voltage to connector terminal 2.

CAUTION:

Do not apply positive (+) battery voltage to any terminals, except terminal 2, to avoid damaging the pulse sensor inside the motor.



b.

Apply negative (-) battery voltage to connector terminals 1 and 7 / 10.


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 7
Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 10
Motor gear rotates counterclockwise


If the result is not as specified, replace the regulator motor assembly.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85720D 3.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH)

a.
B145465E03
1.479,3.635 0.76,3.635 false 2.5,3.635 1.792,3.635 false 1.396,4.01 0.802,4.01 false 2.448,4.01 1.885,4.01 false 1.615,0.01 2.375,0.177 0.76,0.167 10 false Motor Gear 1.958,2.5 2.625,2.667 0.667,0.167 10 false Clockwise 0.563,3.542 0.688,3.708 0.125,0.167 10 false B 2.583,3.542 2.948,3.708 0.365,0.167 10 false GND 0.531,3.927 0.771,4.094 0.24,0.167 10 false UP 2.542,3.927 3.031,4.094 0.49,0.167 10 false DOWN 2.063,1.177 3.167,1.344 1.104,0.167 10 false Counterclockwise

Apply positive (+) battery voltage to connector terminal 2.

CAUTION:

Do not apply positive (+) battery voltage to any terminals, except terminal 2, to avoid damaging the pulse sensor inside the motor.



b.

Apply negative (-) battery voltage to connector terminals 1 and 7 / 10.


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 7
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 10
Motor gear rotates clockwise


If the result is not as specified, replace the regulator motor assembly.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85710E 4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH)

a.
B145466E04
1.573,3.417 0.865,3.417 false 2.604,3.417 1.885,3.417 false 1.49,3.792 0.906,3.792 false 2.552,3.792 1.979,3.792 false 0.813,0.031 1.573,0.198 0.76,0.167 10 false Motor Gear 0.385,1.448 1.052,1.615 0.667,0.167 10 false Clockwise 0.656,3.323 0.781,3.49 0.125,0.167 10 false B 2.677,3.323 3.042,3.49 0.365,0.167 10 false GND 0.646,3.719 0.885,3.885 0.24,0.167 10 false UP 2.635,3.719 3.125,3.885 0.49,0.167 10 false DOWN 0.938,2.365 2.115,2.531 1.177,0.167 10 false Counterclockwise

Apply positive (+) battery voltage to connector terminal 2.

CAUTION:

Do not apply positive (+) battery voltage to any terminals, except terminal 2, to avoid damaging the pulse sensor inside the motor.



b.

Apply negative (-) battery voltage to connector terminals 1 and 7 / 10.


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 7
Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 10
Motor gear rotates counterclockwise


If the result is not as specified, replace the regulator motor assembly.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.