Home › Vehicle Interior › WINDOW / GLASS › BACK DOOR GLASS › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292223 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  REMOVAL  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 28800 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 67939D 2.REMOVE BACK DOOR GARNISH CENTER

Hide 67848 3.REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)

Hide 62582H 4.REMOVE REAR WINDOW SIDE GARNISH LH

Hide 62581H 5.REMOVE REAR WINDOW SIDE GARNISH RH

Hide 67751 6.REMOVE BACK DOOR TRIM BOARD ASSEMBLY

Hide 85190R 7.REMOVE REAR WIPER ARM ASSEMBLY

Hide 85110R 8.REMOVE REAR WIPER MOTOR GROMMET

Hide 85110R 9.REMOVE REAR WIPER MOTOR ASSEMBLY

Hide 76871 10.REMOVE REAR SPOILER

Hide 84280D 11.REMOVE POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

Hide 84270G 12.REMOVE POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

Hide 81590A 13.REMOVE REAR LIGHT ASSEMBLY LH

Hide 81580D 14.REMOVE REAR LIGHT ASSEMBLY RH

Hide 76801 15.REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 75573C 16.REMOVE BACK WINDOW OUTSIDE MOULDING

B140664E01
1.924,2.908 2.218,3.071 0.295,0.163 10 Cut 2.955,0.872 3.250,1.034 0.295,0.163 10 Cut

a.

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Do not damage the body with the knife.



b.

Remove the remaining moulding.


Hide 68131 17.REMOVE BACK DOOR GLASS

B145072

a.

Disconnect the 2 rear window defogger connectors.


b.
B145074E01
0.236,0.358 1.319,0.562 1.084,0.204 10 Protective Tape 1.556,0.468 2.071,0.468 2.071,0.468 2.071,1.283 false

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the back door glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.



c.
B140666E03
1.917,1.073 1.646,1.688 false 1.177,1.698 2.156,1.969 0.979,0.271 10 true Piano Wire

From the interior, insert a piano wire between the vehicle body and back door glass as shown in the illustration.


d.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


e.
B145073

Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed if the glass is not going to be reused.



f.

Cut through the adhesive by pulling the piano wire around the back door glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the back door glass.



g.

Using suction cups, remove the back door glass.


Hide 68131 18.CLEAN BACK DOOR GLASS

BO04421

a.

Clean the outer edge of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the back door glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new back door glass, clean the back door glass with a non-residue solvent.




Hide 19.CLEAN VEHICLE BODY

B106081E48
0.458,1.365 0.458,0.229 false 2.198,1.479 2.198,0.229 false 0.917,1.521 1,1.698 false 2.052,1.781 1.792,1.833 false 0.156,0.063 0.854,0.26 0.698,0.198 10 false Adhesive 1.927,0.052 2.625,0.25 0.698,0.198 10 false Adhesive 0.938,1.74 1.958,1.969 1.021,0.229 10 false Vehicle Body

a.

Using a scraper, remove the moulding and adhesive from the back door glass.


b.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.