Home › Vehicle Interior › MIRROR › OUTER REAR VIEW MIRROR
RM24M0E _58 Vehicle Interior _059593 MIRROR _0292230 OUTER REAR VIEW MIRROR G

MIRROR  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

U188731E02
2.229,2.469 2.5,2.469 false 1.542,0.417 1.781,0.583 0.24,0.167 10 false (A) 1.406,1.26 1.677,1.448 0.271,0.188 10 true (B) 1.938,0.833 2.177,1.021 0.24,0.188 10 true (D) 0.813,0.729 1.052,0.917 0.24,0.188 10 true (C) 2.531,2.385 2.802,2.563 0.271,0.177 10 false MV 2.708,1.979 2.979,2.156 0.271,0.177 10 false M+ 2.156,1.729 2.427,1.906 0.271,0.177 10 false MH

a.

Check the mirror operation.

i.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) →Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward (A)
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 6 (MV)
Turns downward (B)
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left (C)
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 4 (MH)
Turns right (D)


If the result is not as specified, replace the mirror assembly.



b.
B141559E02
1.385,2.479 0.896,2.125 false 1.396,2.708 0.875,2.958 false 0.646,2.01 0.958,2.219 0.313,0.208 10 false H+ 0.688,2.885 0.917,3.094 0.229,0.208 10 false H-

w/ Mirror Heater:

Check the mirror heater resistance.

i.

Measure the resistance of the mirror heater.

Standard resistance:
Tester Connection Condition Specified Condition
2 (H+) - 8 (H-) 25°C (77°F) 3.2 to 6.9 Ω


If the result is not as specified, replace the mirror.


ii.

Connect the battery's positive (+) lead to terminal 2 (H+) and the negative (-) lead to terminal 8 (H-), and then check that the mirror becomes warm.

OK:

Mirror becomes warm.


HINT:

It takes a short time for the mirror to become warm.


If the result is not as specified, replace the mirror assembly.



Hide 2.INSPECT OUTER MIRROR RETRACTOR LH (w/ Mirror Heater)

a.
B135738E01
0.577,4.173 0.850,4.353 0.274,0.180 10 MF 0.561,3.407 0.835,3.587 0.274,0.180 10 MR 1.171,0.193 1.445,0.372 0.274,0.180 10 A 0.683,1.184 0.957,1.363 0.274,0.180 10 B 0.711,2.369 0.984,2.549 0.274,0.180 10 C 1.35,2.907 1.624,3.087 0.274,0.180 10 D 2.076,3.314 2.349,3.494 0.274,0.180 10 E 1.954,0.257 2.663,0.644 0.708,0.387 10 Forward Position 0.094,2.717 0.705,3.152 0.611,0.435 10 Driving Position 2.418,2.833 3.066,3.268 0.647,0.435 10 Retracted Position 1.534,3.946 1.094,3.482 1.094,3.482 0.868,3.482 false 1.566,4.238 1.281,4.496 1.281,4.496 0.871,4.264 false

Check the retractor operation.

i.

Set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Forward position A Moves from A to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position A Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between forward position A and driving position C Moves from B to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position A and driving position C Moves from B to forward position A
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Driving position C Moves from C to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position C Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between driving position C and retracted position E Moves from D to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position C and retracted position E Moves from D to driving position C
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Retracted position E Does not move
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position E Moves from E to driving position C


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



If the result is not as specified, replace the outer mirror retractor LH.



Hide 87910 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

U188732E02
2.219,2.479 2.49,2.479 false 1.792,0.229 2.031,0.396 0.24,0.167 10 false (A) 1.865,1.25 2.135,1.438 0.271,0.188 10 true (B) 2.406,0.708 2.646,0.896 0.24,0.188 10 true (C) 1.271,0.708 1.51,0.896 0.24,0.188 10 true (D) 2.531,2.396 2.802,2.573 0.271,0.177 10 false MV 2.677,1.99 2.948,2.167 0.271,0.177 10 false M+ 2.167,1.74 2.438,1.917 0.271,0.177 10 false MH

a.

Check the mirror operation.

i.

Apply battery voltage and check the operation of the mirror.

OK:
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward (A)
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 6 (MV)
Turns downward (B)
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns right (C)
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 4 (MH)
Turns left (D)


If the result is not as specified, replace the mirror assembly.



b.
B141562E03
1.385,2.5 0.854,2.083 false 1.385,2.708 0.844,2.865 false 0.583,1.979 0.844,2.146 0.26,0.167 10 false H+ 0.625,2.823 0.885,2.99 0.26,0.167 10 false H-

w/ Mirror Heater:

Check the resistance.

i.

Apply battery voltage and check the operation of the mirror.

Standard resistance:
Tester Connection Condition Specified Condition
8 (H-) - 2 (H+) 25°C (77°F) 3.2 to 6.9 Ω


If the result is not as specified, replace the mirror.


ii.

Connect the battery's positive (+) lead to terminal 2 (H+) and the negative (-) lead to terminal 8 (H-), and then check that the mirror becomes warm.

OK:

Mirror becomes warm.


HINT:

It takes a short time for the mirror to become warm.


If the result is not as specified, replace the mirror assembly.



Hide 4.INSPECT OUTER MIRROR RETRACTOR RH (w/ Mirror Heater)

a.
U188637E01
0.643,4.199 0.916,4.379 0.274,0.180 10 MF 0.614,3.684 0.888,3.864 0.274,0.180 10 MR 2.072,0.224 2.346,0.404 0.274,0.180 10 A 2.454,1.295 2.728,1.474 0.274,0.180 10 B 2.468,2.367 2.741,2.547 0.274,0.180 10 C 1.797,2.902 2.070,3.082 0.274,0.180 10 D 1.173,3.304 1.447,3.484 0.274,0.180 10 E 0.94,0.077 1.648,0.463 0.708,0.387 10 Forward Position 2.655,2.623 3.266,3.058 0.611,0.435 10 Driving Position 0.158,3.031 0.805,3.466 0.647,0.435 10 Retracted Position 1.538,4.309 1.158,4.464 1.158,4.464 0.92,4.303 false

Check the retractor operation.

i.

Set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) →Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Forward position A Moves from A to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position A Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between forward position A and driving position C Moves from B to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position A and driving position C Moves from B to forward position A
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Driving position C Moves from C to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position C Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between driving position C and retracted position E Moves from D to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position C and retracted position E Moves from D to driving position C
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Retracted position E Does not move
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position E Moves from E to driving position C


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



If the result is not as specified, replace the outer mirror retractor RH.