Home › Vehicle Interior › SLIDING ROOF › SLIDING ROOF SYSTEM
RM24M0E _58 Vehicle Interior _059597 SLIDING ROOF _0292254 SLIDING ROOF SYSTEM C

SLIDING ROOF  SLIDING ROOF SYSTEM  B1273  Sliding Roof ECU Communication Stop  


DESCRIPTION

DTC B1273 is output when communication between the sliding roof drive gear (rear sunshade control ECU) and main body ECU stops for more than 10 seconds.

NOTICE:

When using the intelligent tester to troubleshoot the LIN communication line: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 seconds intervals until communication between the tester and vehicle begins.

DTC No. DTC Detection Condition Trouble Area
B1273 No communication from sliding roof drive gear for more than 10 seconds
·

Sliding roof drive gear (Rear sunshade control ECU)

·

Main body ECU

·

Wire harness




WIRING DIAGRAM

B143323E02
5.388,2.272 6.391,2.616 1.003,0.343 10 Rear Sunshade Control ECU 4.61,3.877 6.160,4.055 1.549,0.178 10 Sliding Roof Drive Gear 0.322,3.034 1.385,3.206 1.063,0.172 10 Main Body ECU 2.833,1.363 3.110,1.515 0.277,0.152 10 LIN 1.028,1.579 1.361,1.797 0.333,0.218 10 LIN2 1.028,1.579 1.361,1.797 0.333,0.218 10 LIN2 5.325,1.579 5.658,1.797 0.333,0.218 10 LIN2 1.48,1.712 1.671,1.857 0.191,0.145 10 10 0.317,2.913 0.609,3.059 0.291,0.145 10 G59 5.046,1.712 5.150,1.875 0.104,0.163 10 4 4.622,3.733 4.837,3.931 0.215,0.198 10 N2

PROCEDURE

1.CHECK FOR DTC

NG

2.READ VALUE USING INTELLIGENT TESTER (COMMUNICATION SLIDING ROOF DRIVE GEAR)

OK

SYSTEM IS OK

2.READ VALUE USING INTELLIGENT TESTER (COMMUNICATION SLIDING ROOF DRIVE GEAR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG).


c.

Read the Data List according to the display on the tester.

Main body ECU:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Communication Slide Roof Connection status between sliding roof drive gear and main body ECU / ON or STOP OK: Connection
STOP: No connection
-




NG

3.CHECK WIRE HARNESS (SLIDING ROOF DRIVE GEAR - MAIN BODY ECU AND BODY GROUND)

OK

REPLACE MAIN BODY ECU

3.CHECK WIRE HARNESS (SLIDING ROOF DRIVE GEAR - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the N2 drive gear connector.


b.

Disconnect the G59 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
N2-4 (LIN2) - G59-10 (LIN2) Below 1 Ω
N2-4 (LIN2) - Body ground 10 kΩ or higher




OK

4.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FOR DTC

OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (REAR SUNSHADE CONTROL ECU)

NG

REPLACE MAIN BODY ECU