Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2014.09–2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM U

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

Turn the engine switch off before measuring the resistances of the main wire and the branch wire.

·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the engine switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


JUNCTION CONNECTOR (for LHD)


a.

No. 1 Junction Connector

U189218E02
3.333,1.5 2.802,0.229 2.802,0.229 2.688,0.229 false 3.896,1.51 4.385,1.104 4.385,1.104 4.5,1.104 false 3.313,1.656 2.24,1.094 2.24,1.094 1.99,1.094 false 3.49,1.708 3.188,2.083 3.188,2.083 3.125,2.083 false 3.583,1.719 3.844,2.292 3.844,2.292 3.906,2.292 false 3.74,1.719 3.906,1.99 3.906,1.99 3.938,1.99 false 3.469,0.458 3.76,0.625 0.292,0.167 10 false A29 0.24,0.156 2.74,0.333 2.5,0.177 10 false CANH (for Brake Actuator Assembly)*1 3.958,2.208 6.458,2.375 2.5,0.167 10 false CANL (for Brake Actuator Assembly)*1 2.073,1.99 3.125,2.167 1.052,0.177 10 false CANH (for ECM) 4.552,1.031 5.604,1.208 1.052,0.177 10 false CANL (for ECM) 0.542,1.042 2.031,1.604 1.49,0.563 10 false CANH (for No. 2 CAN Junction Connector LH) 3.99,1.906 6.875,2.094 2.885,0.188 10 false CANL (for No. 2 CAN Junction Connector LH) 0.188,0.5 2.844,0.677 2.656,0.177 10 false CANH (for ABS and Traction Actuator) *2 3.948,2.448 6.615,2.615 2.667,0.167 10 false CANL (for ABS and Traction Actuator)*2 0.25,2.208 1.073,2.354 0.823,0.146 10 false *1: w/o VSC 0.25,2.49 1.073,2.635 0.823,0.146 10 false *2: w/ VSC

No. 1 Junction Connector Wiring Color Connect to
CANH (A29-1) B Brake actuator assembly (skid control ECU)*1
ABS and traction actuator (skid control ECU)*2
CANL (A29-5) W Brake actuator assembly (skid control ECU)*1
ABS and traction actuator (skid control ECU)*2
CANH (A29-4) B ECM
CANL (A29-7) W ECM
CANH (A29-3) B No. 2 CAN junction connector LH
CANL (A29-6) W No. 2 CAN junction connector LH

*1: w/o VSC

*2: w/ VSC


b.

No. 2 CAN Junction Connector LH

U189640E01
1.345,0.74 1.624,0.922 0.280,0.181 10 G70 1.874,0.747 2.154,0.928 0.280,0.181 10 G71 3.989,0.747 4.268,0.928 0.280,0.181 10 G75 4.476,0.747 4.755,0.928 0.280,0.181 10 G74 4.971,0.747 5.251,0.928 0.280,0.181 10 G73 5.484,0.747 5.764,0.928 0.280,0.181 10 G72 2.387,0.747 2.666,0.928 0.280,0.181 10 G69 2.882,0.747 3.162,0.928 0.280,0.181 10 G96 0.819,0.302 2.615,0.608 1.796,0.307 10 Junction Connector B Side 3.133,3.037 4.114,3.687 0.981,0.650 10 No. 2 CAN Junction Connector LH 3.902,0.302 5.698,0.608 1.796,0.307 10 Junction Connector A Side 5.386,2.184 6.314,2.491 0.929,0.307 10 Earth Terminal 1.478,0.929 1.873,1.409 false 2.007,0.935 2.232,1.409 false 2.52,0.935 2.607,1.404 false 3.016,0.935 2.969,1.404 false 4.126,0.935 4.215,1.401 false 4.613,0.935 4.577,1.405 false 5.109,0.935 4.952,1.407 false 5.621,0.935 5.314,1.407 false 2.639,2.832 2.940,2.988 0.302,0.157 10 G96 2.639,3.126 2.940,3.283 0.302,0.157 10 G69 2.639,3.404 2.940,3.561 0.302,0.157 10 G71 4.208,2.83 4.510,2.987 0.302,0.157 10 G75 4.208,3.125 4.510,3.282 0.302,0.157 10 G74 4.208,3.404 4.510,3.561 0.302,0.157 10 G73 4.208,3.679 4.510,3.835 0.302,0.157 10 G72 2.639,3.681 2.940,3.837 0.302,0.157 10 G70 5.841,2.151 5.685,1.322 false

Wiring color
Junction Connector A Side Color (CANH Side) Color (CANL Side)
Steering angle sensor* (G72) BR W
No. 1 CAN junction connector RH (G73) B W
No. 1 junction connector (G74) L W
Main body ECU (G75) B W

*: w/ VSC or w/ AFS

Wiring color
Junction Connector B Side Color (CANH Side) Color (CANL Side)
DLC3 (G70) GR W
Center airbag sensor assembly (G71) Y W
Power steering ECU (G69) Y W
Navigation receiver assembly* (G96) SB W

*: w/ Navigation System

HINT:
·

The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.

·

The connectors can be connected to any terminals on the same side.




c.

No. 1 CAN Junction Connector RH

U189642E02
2,0.958 2.229,1.427 false 4.604,0.958 4.573,1.427 false 5.104,0.958 4.948,1.427 false 5.615,0.958 5.313,1.427 false 5.833,2.146 5.677,1.323 false 1.865,0.75 2.146,0.927 0.281,0.177 10 false G79 4.469,0.75 4.75,0.927 0.281,0.177 10 false G95 4.969,0.75 5.25,0.927 0.281,0.177 10 false G78 5.479,0.75 5.76,0.927 0.281,0.177 10 false G77 0.813,0.302 2.604,0.604 1.792,0.302 10 false Junction Connector B Side 3.125,3.031 4.104,3.677 0.979,0.646 10 false No. 1 CAN Junction Connector RH 3.896,0.302 5.688,0.604 1.792,0.302 10 false Junction Connector A Side 5.385,2.177 6.313,2.479 0.927,0.302 10 false Earth Terminal 2.635,3.406 2.938,3.563 0.302,0.156 10 false G79 4.198,3.125 4.5,3.281 0.302,0.156 10 false G95 4.198,3.406 4.5,3.563 0.302,0.156 10 false G78 4.198,3.677 4.5,3.833 0.302,0.156 10 false G77

Wiring color
Junction Connector A Side Color (CANH Side) Color (CANL Side)
Air conditioning amplifier (G77) V W
No. 2 CAN junction connector LH (G78) B W
AFS ECU* (G95) Y SB

*: w/ AFS

Wiring color
Junction Connector B Side Color (CANH Side) Color (CANL Side)
No. 2 junction connector (G79) L W

HINT:
·

The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.

·

The connectors can be connected to any terminals on the same side.




d.

No. 2 Junction Connector

U189241E01
1.625,1.341 1.928,1.505 0.303,0.164 10 N35 0.558,0.591 3.447,0.752 2.889,0.161 10 CANH (for No. 1 CAN Junction Connector RH) 0.44,0.08 3.309,0.249 2.869,0.170 10 CANL (for No. 1 CAN Junction Connector RH) 1.257,0.939 3.763,1.097 2.506,0.158 10 CANH (for Yaw Rate Sensor)*1 3.766,1.034 6.052,1.204 2.286,0.170 10 CANH (for Combination Meter ECU) 1.178,2.98 3.659,3.155 2.481,0.174 10 CANL (for Yaw Rate Sensor)*1 3.715,0.706 6.013,0.899 2.298,0.193 10 CANH (for Combination Meter ECU) 3.506,0.367 6.391,0.537 2.885,0.170 10 CANH (for No. 2 CAN Junction Connector RH) 3.74,0.012 6.331,0.175 2.591,0.163 10 CANH (for Power Slide Door ECU RH)*2 4.384,3.476 7.108,3.639 2.724,0.163 10 CANL (for Power Slide Door ECU RH)*2 1.128,2.7 3.370,2.886 2.242,0.186 10 CANL (for Combination Meter ECU) 3.688,3.141 6.578,3.311 2.890,0.170 10 CANL (for No. 2 CAN Junction Connector RH) 3.424,2.777 5.733,2.946 2.309,0.170 10 CANL (for Combination Meter ECU) 4.542,1.354 4.845,1.518 0.303,0.164 10 N35 0.042,3.197 0.768,3.353 0.725,0.156 10 *1: w/ VSC 0.042,3.492 2.115,3.648 2.073,0.156 10 *2: w/ Power Slide Door System

Junction Connector Wiring Color Connect to
CANH (N35-1) B No. 1 CAN junction connector RH
CANL (N35-6) W No. 1 CAN junction connector RH
CANH (N35-2) B Yaw rate sensor*1
CANL (N35-7) W Yaw rate sensor*1
CANH (N35-3) B Combination meter assembly (Combination meter ECU)
CANL (N35-8) W Combination meter assembly (Combination meter ECU)
CANH (N35-5) B No. 2 CAN junction connector RH
CANL (N35-10) W No. 2 CAN junction connector RH
CANH (N35-12) B Power slide door ECU RH*2
CANL (N35-11) W Power slide door ECU RH*2
CANH (N35-4) B Combination meter assembly (Combination meter ECU)
CANL (N35-9) W Combination meter assembly (Combination meter ECU)

*1: w/ VSC

*2: w/ Power Slide Door System


e.

No. 3 Junction Connector

U189242E02
1.938,2.083 2.802,0.208 2.802,0.208 2.635,0.208 false 1.573,2.094 2.208,0.708 2.208,0.708 1.969,0.708 false 2.104,2.406 2.104,2.667 2.104,2.667 1.833,2.667 false 4.635,2.073 3.49,0.281 3.49,0.281 3.656,0.281 false 5.469,2.063 6.813,0.708 6.813,0.708 6.552,0.708 false 3.458,1.844 3.802,2.042 0.344,0.198 10 false M25 0.271,0.635 2.01,0.802 1.74,0.167 10 false CANH (for Main Body ECU) 0.167,2.594 1.906,2.792 1.74,0.198 10 false CANL (for Main Body ECU) 3.729,0.188 6.74,0.385 3.01,0.198 10 false CANH (for No. 2 CAN Junction Connector RH) 4.042,2.969 6.927,3.177 2.885,0.208 10 false CANL (for No. 2 CAN Junction Connector RH) 4.083,3.375 6.792,3.583 2.708,0.208 10 false CANH (for Power Back Door ECU)*2 4.313,0.625 6.854,0.781 2.542,0.156 10 false CANL (for Power Back Door ECU)*2 0.177,0.146 2.927,0.313 2.75,0.167 10 false CANH (for Power Slide Door ECU LH)*1 0.365,2.865 2.906,3.042 2.542,0.177 10 false CANL (for Power Slide Door ECU LH)*1 0.094,3.219 2.531,3.375 2.438,0.156 10 false *1: w/ Power Slide Door System 0.094,3.5 2.948,3.656 2.854,0.156 10 false *2: w/ Power Back Door System

Junction Connector Wiring Color Connect to
CANH (M25-1) B Main body ECU
CANL (M25-9) W Main body ECU
CANH (M25-3) B Power slide door ECU LH*1
CANL (M25-11) W Power slide door ECU LH*1
CANH (M25-8) B Power back door ECU*2
CANL (M25-4) W Power back door ECU*2
CANH (M25-2) B No. 2 CAN junction connector RH
CANL (M25-10) W No. 2 CAN junction connector RH

*1: w/ Power Slide Door System

*2: w/ Power Back Door System


f.

No. 2 CAN Junction Connector RH

U189100E02
5.76,1.563 5.958,2.438 false 2.094,1.177 1.917,1.677 false 5.448,1.188 5.354,1.688 false 4.74,1.177 4.646,1.677 false 5.5,2.469 6.49,2.615 0.99,0.146 10 false Earth Terminal 4.25,0.469 6.167,0.698 1.917,0.229 10 false Junction Connector A Side 1,0.479 2.729,0.677 1.729,0.198 10 false Junction Connector B Side 2.719,3.688 3.01,3.833 0.292,0.146 10 false G82 1.958,1 2.25,1.146 0.292,0.146 10 false G82 3.188,3.146 4.083,3.75 0.896,0.604 10 false No. 2 CAN Junction Connector RH 4.281,3.406 4.573,3.552 0.292,0.146 10 false G81 4.615,1 4.906,1.146 0.292,0.146 10 false G81 4.281,3.958 4.573,4.104 0.292,0.146 10 false G80 5.313,1.01 5.604,1.156 0.292,0.146 10 false G80

Wiring color
Junction Connector A Side Color (CANH Side) Color (CANL Side)
No. 3 junction connector (G81) R W
Certification ECU (G80) SB W

Wiring color
Junction Connector B Side Color (CANH Side) Color (CANL Side)
No. 2 junction connector (G82) V W

HINT:
·

The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.

·

The connectors can be connected to any terminals on the same side.





JUNCTION CONNECTOR (for RHD)


a.

No. 2 CAN Junction Connector LH

U189651E01
5.486,2.453 6.475,2.602 0.989,0.149 10 Earth Terminal 5.777,1.545 5.977,2.424 false 4.062,0.49 5.755,0.628 1.693,0.137 10 Junction Connector A Side 0.951,0.49 2.644,0.628 1.693,0.137 10 Junction Connector B Side 1.256,1.024 1.550,1.166 0.295,0.142 10 G77 2.732,3.989 3.027,4.131 0.295,0.142 10 G77 3.223,3.134 4.124,3.661 0.900,0.527 10 No. 2 CAN Junction Connector LH 1.385,1.198 1.559,1.703 false 2.291,1.024 2.586,1.166 0.295,0.142 10 G73 2.748,3.435 3.042,3.577 0.295,0.142 10 G73 2.429,1.198 2.324,1.703 false 4.013,1.01 4.308,1.152 0.295,0.142 10 G75 4.304,3.158 4.598,3.300 0.295,0.142 10 G75 4.456,1.01 4.750,1.152 0.295,0.142 10 G74 4.304,3.44 4.598,3.582 0.295,0.142 10 G74 4.992,1.01 5.287,1.152 0.295,0.142 10 G84 4.304,3.718 4.598,3.860 0.295,0.142 10 G84 4.142,1.184 4.317,1.689 false 4.584,1.184 4.68,1.681 false 5.134,1.184 5.039,1.681 false

Wiring color
Junction Connector A Side Color (CANH Side) Color (CANL Side)
ECM (G74) L W
Brake actuator assembly (Skid control ECU)*1 (G84)
ABS and traction actuator (Skid control ECU)*2 (G84)
BR W
Main body ECU (G75) B W

*1: w/o VSC

*2: w/ VSC

Wiring color
Junction Connector B Side Color (CANH Side) Color (CANL Side)
Air conditioning amplifier (G77) V W
No. 5 CAN junction connector RH (G73) B W

HINT:
·

The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.

·

The connectors can be connected to any terminals on the same side.




b.

No. 5 Junction Connector

U189652E01
2.062,1.354 2.437,1.510 0.375,0.156 10 G103 3.609,1.41 3.304,0.455 3.304,0.455 3.234,0.455 false 0.899,0.379 3.241,0.535 2.343,0.156 10 CANH (for No. 2 Junction Connector) 1.073,2.003 3.385,2.159 2.312,0.156 10 CANL (for No. 2 Junction Connector) 3.712,1.413 4.057,0.297 4.057,0.297 4.138,0.297 false 3.923,1.415 4.138,0.702 4.138,0.702 4.224,0.702 false 4.177,0.231 6.898,0.387 2.721,0.156 10 CANH (for Center Airbag Sensor Assembly) 0.717,2.371 3.438,2.526 2.721,0.156 10 CANL (for Center Airbag Sensor Assembly) 4.254,0.633 6.333,0.789 2.079,0.156 10 CANH (for Power Steering ECU) 4.301,2.249 6.380,2.405 2.079,0.156 10 CANL (for Power Steering ECU) 3.622,1.667 3.492,2.076 3.492,2.076 3.384,2.076 false 3.719,1.656 3.554,2.434 3.554,2.434 3.446,2.434 false 3.924,1.661 4.193,2.324 4.193,2.324 4.279,2.324 false 4.035,1.406 4.135,1.035 4.135,1.035 4.179,1.035 false 4.195,0.966 7.070,1.296 2.875,0.330 10 CANH (for No. 2 CAN Junction Connector LH) 4.034,1.665 4.166,1.929 4.166,1.929 4.21,1.929 false 4.228,1.867 7.072,2.196 2.844,0.330 10 CANL (for No. 2 CAN Junction Connector LH)

Junction Connector Wiring Color Connect to
CANH (G103-7) B No. 2 junction connector
CANL (G103-18) W No. 2 junction connector
CANH (G103-8) Y Center airbag sensor assembly
CANL (G103-19) W Center airbag sensor assembly
CANH (G103-10) Y Power steering ECU
CANL (G103-21) W Power steering ECU
CANH (G103-11) B No. 2 CAN junction connector LH
CANL (G103-22) W No. 2 CAN junction connector LH


c.

No. 2 Junction Connector

U189243E01
1.625,1.341 1.928,1.505 0.303,0.164 10 N35 0.558,0.591 3.289,0.752 2.732,0.161 10 CANH (for No. 4 Junction Connector) 0.44,0.08 3.166,0.249 2.726,0.170 10 CANL (for No. 4 Junction Connector) 1.089,0.939 3.058,1.097 1.968,0.158 10 CANH (for Yaw Rate Sensor)*1 0.884,2.98 2.827,3.155 1.943,0.174 10 CANL (for Yaw Rate Sensor)*1 3.897,0.706 6.195,0.899 2.298,0.193 10 CANH (for Combination Meter ECU) 3.8,0.367 6.685,0.537 2.885,0.170 10 CANH (for No. 2 CAN Junction Connector RH) 3.329,1.035 6.214,1.205 2.885,0.170 10 CANH (for No. 5 CAN Junction Connector RH) 3.81,0 6.401,0.163 2.591,0.163 10 CANH (for Power Slide Door ECU RH)*2 4.412,3.476 6.929,3.639 2.517,0.163 10 CANL (for Power Slide Door ECU RH)*2 3.688,3.141 6.578,3.311 2.890,0.170 10 CANL (for No. 2 CAN Junction Connector RH) 0.489,2.695 3.371,2.865 2.882,0.170 10 CANL (for No. 5 CAN Junction Connector RH) 3.424,2.777 5.733,2.946 2.309,0.170 10 CANL (for Combination Meter ECU) 4.542,1.354 4.845,1.518 0.303,0.164 10 N35 0.042,3.492 2.115,3.648 2.073,0.156 10 *2: w/ Power Slide Door System 1.905,2.394 1.905,2.673 false 0.048,3.232 2.120,3.388 2.073,0.156 10 *1: w/ VSC

Junction Connector Wiring Color Connect to
CANH (N35-1) B No. 4 junction connector
CANL (N35-6) W No. 4 junction connector
CANH (N35-2) B Yaw rate sensor*1
CANL (N35-7) W Yaw rate sensor*1
CANH (N35-3) B No. 5 CAN junction connector RH
CANL (N35-8) W No. 5 CAN junction connector RH
CANH (N35-5) B No. 2 CAN junction connector RH
CANL (N35-10) W No. 2 CAN junction connector RH
CANH (N35-12) B Power slide door ECU RH*2
CANL (N35-11) W Power slide door ECU RH*2
CANH (N35-4) B Combination meter assembly (Combination meter ECU)
CANL (N35-9) W Combination meter assembly (Combination meter ECU)

*1: w/ VSC

*2: w/ Power Slide Door System


d.

Junction Block LH

U189221E02
3.573,2.052 3.75,1.896 3.75,1.896 4.219,1.896 false 3.625,2.073 3.729,2.26 3.729,2.26 4.208,2.26 false 3.51,1.427 3.844,1.167 3.844,1.167 4.531,1.167 false 3.76,1.458 3.938,1.635 3.938,1.635 4.542,1.635 false 2.5,1.833 3.208,1.25 false 2.5,1.927 3.208,1.896 false 3.313,1.156 3.479,1.302 0.167,0.146 10 false LJ 3.302,1.813 3.5,1.958 0.198,0.146 10 false LK 4.573,1.083 6.76,1.26 2.188,0.177 10 false CA2H (for Network Gateway ECU) 4.583,1.542 6.719,1.76 2.135,0.219 10 false CA2L (for Network Gateway ECU) 4.26,2.177 7.042,2.375 2.781,0.198 10 false CANL (for No. 1 CAN Junction Connector LH) 4.26,1.813 7.125,2 2.865,0.188 10 false CANH (for No. 1 CAN Junction Connector LH)

Junction Block LH Wiring Color Connect to
CA2H (LJ-1) V Network gateway ECU
CA2L (LJ-5) P Network gateway ECU
CANH (LK-2) V No. 1 CAN junction connector LH
CANL (LK-3) P No. 1 CAN junction connector LH


e.

No. 1 CAN Junction Connector LH

U189103E02
5.771,1.563 5.969,2.448 false 5.135,1.188 5.042,1.677 false 2.427,1.177 2.333,1.667 false 5.49,2.448 6.479,2.594 0.99,0.146 10 false Earth Terminal 4.063,0.479 5.76,0.646 1.698,0.167 10 false Junction Connector A Side 0.948,0.479 2.646,0.656 1.698,0.177 10 false Junction Connector B Side 4.979,1.01 5.271,1.156 0.292,0.146 10 false G67 4.302,3.688 4.594,3.833 0.292,0.146 10 false G67 2.281,1 2.573,1.146 0.292,0.146 10 false G83 2.635,0.979 2.854,1.177 0.219,0.198 10 false * 2.74,3.417 3.031,3.563 0.292,0.146 10 false G83 3.24,3.125 4.156,3.604 0.917,0.479 10 false No. 1 CAN Junction Connector LH 0.229,4.385 1.281,4.573 1.052,0.188 10 false *: w/ AFS

Wiring color
Junction Connector A Side Color (CANH Side) Color (CANL Side)
Junction block LH (G67) V P

Wiring color
Junction Connector B Side Color (CANH Side) Color (CANL Side)
AFS ECU (G83)* GR W

*: w/ AFS

HINT:
·

The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.

·

The connectors can be connected to any terminals on the same side.




f.

No. 4 Junction Connector

U189654E02
3.708,1.427 3.396,0.49 3.396,0.49 3.333,0.49 false 3.615,1.427 3.396,0.76 3.396,0.76 3.323,0.76 false 3.604,1.667 3.458,1.979 3.458,1.979 3.385,1.979 false 3.813,1.427 4.281,0.313 4.281,0.313 4.365,0.313 false 3.927,1.427 4.281,0.719 4.281,0.719 4.365,0.719 false 3.719,1.677 3.49,2.313 3.49,2.313 3.385,2.313 false 3.833,1.677 3.573,2.573 3.573,2.573 3.458,2.573 false 3.927,1.677 4.135,2.24 4.135,2.24 4.229,2.24 false 4.052,1.427 4.188,1.229 4.188,1.229 4.24,1.229 false 4.031,1.677 4.146,1.875 4.146,1.875 4.188,1.875 false 2.073,1.365 2.458,1.552 0.385,0.188 10 false G104 1.125,0.396 3.375,0.615 2.25,0.219 10 false CANH (for Combination Meter ECU) 1.188,2.219 3.469,2.417 2.281,0.198 10 false CANL (for Combination Meter ECU) 1.063,0.677 3.365,0.875 2.302,0.198 10 false CANH (for No. 2 Junction Connector) 1.115,1.885 3.427,2.115 2.313,0.229 10 false CANL (for No. 2 Junction Connector) 4.417,0.24 6.74,0.396 2.323,0.156 10 false CANH (for Steering Angle Sensor)* 1.323,2.469 3.531,2.677 2.208,0.208 10 false CANL (for Steering Angle Sensor)* 4.406,0.625 6.729,0.781 2.323,0.156 10 false CANH (for DLC3) 4.25,2.167 5.823,2.417 1.573,0.25 10 false CANL (for DLC3) 4.271,1.146 6.615,1.479 2.344,0.333 10 false CANH (for Network Gateway ECU) 4.219,1.792 6.458,2.125 2.24,0.333 10 false CANL (for Network Gateway ECU) 4.646,2.479 6.198,2.698 1.552,0.219 10 false *: w/ VSC or w/ AFS

Junction Connector Wiring Color Connect to
CANH (G104-7) B No. 2 junction connector
CANL (G104-18) W No. 2 junction connector
CANH (G104-8) B Combination meter assembly (Combination meter ECU)
CANL (G104-19) W Combination meter assembly (Combination meter ECU)
CANH (G104-9) BR Steering angle sensor*
CANL (G104-20) W Steering angle sensor*
CANH (G104-10) GR DLC3
CANL (G104-21) W DLC3
CANH (G104-11) G Network gateway ECU
CANL (G104-22) W Network gateway ECU

*: w/ VSC or w/ AFS


g.

No. 3 Junction Connector

U189077E02
3.958,1.729 4.531,1.563 false 2.938,1.594 1.958,1.052 false 3.354,1.729 2.406,1.677 false 3.365,1.5 3.156,0.177 3.156,0.177 3.073,0.177 false 3.969,1.5 4.396,0.646 4.396,0.646 4.469,0.646 false 3.552,1.844 3.719,2.479 3.719,2.479 3.792,2.479 false 3.771,1.844 3.885,2.177 3.885,2.177 3.958,2.177 false 3.229,1.479 3.063,0.531 3.063,0.531 2.99,0.531 false 3.448,0.458 3.802,0.615 0.354,0.156 10 false M25 0.615,0.104 3.24,0.438 2.625,0.333 10 false CANH (for Power Slide Door ECU LH)*1 4.573,1.458 7.104,1.667 2.531,0.208 10 false CANL (for Power Slide Door ECU LH)*1 4.521,0.573 6.979,0.781 2.458,0.208 10 false CANL (for Power Back Door ECU)*2 0.125,1.594 2.469,1.938 2.344,0.344 10 false CANH (for Power Back Door ECU)*2 0.156,0.448 3.083,0.771 2.927,0.323 10 false CANH (for No. 2 CAN Junction Connector RH) 4.01,2.104 6.896,2.333 2.885,0.229 10 false CANL (for No. 2 CAN Junction Connector RH) 0.229,0.969 1.969,1.135 1.74,0.167 10 false CANH (for Main Body ECU) 3.844,2.385 5.583,2.74 1.74,0.354 10 false CANL (for Main Body ECU) 0.094,2.115 2.625,2.438 2.531,0.323 10 false *1: w/ Power Slide Door System 0.104,2.448 2.688,2.771 2.583,0.323 10 false *2: w/ Power Back Door System

Junction Connector Wiring Color Connect to
CANH (M25-1) B Main body ECU
CANL (M25-9) W Main body ECU
CANH (M25-2) B No. 2 CAN junction connector RH
CANL (M25-10) W No. 2 CAN junction connector RH
CANH (M25-3) B Power slide door ECU LH*1
CANL (M25-11) W Power slide door ECU LH*1
CANH (M25-8) B Power back door ECU*2
CANL (M25-4) W Power back door ECU*2

*1: w/ Power Slide Door System

*2: w/ Power Back Door System


h.

No. 2 CAN Junction Connector RH

U189493E01
5.472,2.453 6.461,2.602 0.989,0.149 10 Earth Terminal 5.763,1.545 5.962,2.424 false 4.048,0.49 5.741,0.628 1.693,0.137 10 Junction Connector A Side 0.937,0.49 2.630,0.628 1.693,0.137 10 Junction Connector B Side 4.978,1.01 5.273,1.152 0.295,0.142 10 G81 4.291,3.71 4.585,3.852 0.295,0.142 10 G81 3.199,3.122 4.137,3.623 0.938,0.501 10 No. 2 CAN Junction Connector RH 5.12,1.184 5.025,1.681 false 5.389,1.01 5.684,1.152 0.295,0.142 10 G80 5.531,1.184 5.436,1.681 false 1.515,1.01 1.810,1.152 0.295,0.142 10 G82 2.712,3.953 3.006,4.095 0.295,0.142 10 G82 4.29,3.953 4.585,4.095 0.295,0.142 10 G80 1.65,1.184 1.554,1.681 false

Wiring color
Junction Connector A Side Color (CANH Side) Color (CANL Side)
Certification ECU (G80) SB W
No. 3 junction connector (G81) R W

Wiring color
Junction Connector B Side Color (CANH Side) Color (CANL Side)
No. 2 junction connector (G82) V W

HINT:
·

The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.

·

The connectors can be connected to any terminals on the same side.





TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR LH*1, NO. 2 CAN JUNCTION CONNECTOR LH, NO. 1 CAN JUNCTION CONNECTOR RH*2, NO. 2 CAN JUNCTION CONNECTOR RH)


C135249

Terminal Terminal Symbol
1 CANH
2 CANL

*1: for RHD

*2: for LHD


CHECK DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.
U190030E02
1.948,1.458 1.854,1.781 false 2.333,1.458 2.448,1.802 false 1.573,0.927 1.125,0.417 false 1.958,0.927 2.333,0.427 false 2.333,0.25 2.781,0.427 0.448,0.177 10 false CANH 0.885,0.25 1.177,0.427 0.292,0.177 10 false CG 1.594,1.813 2.021,1.99 0.427,0.177 10 false CANL 2.333,1.823 2.625,2 0.292,0.177 10 false BAT 1.563,0.26 1.875,0.427 0.313,0.167 10 false G15

Measure the resistance of the connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (G15-6) - CANL (G15-14) GR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (G15-6) - CG (G15-4) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (G15-14) - CG (G15-4) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (G15-6) - BAT (G15-16) GR - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (G15-14) - BAT (G15-16) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


HINT:

For vehicles without VSC only.


U189187E01
3.478,0.5 3.759,0.655 0.281,0.156 10 A22 1.796,2.184 2.216,2.345 0.420,0.161 10 CANH 2.423,1.476 1.995,2.166 false 1.516,0.573 1.936,0.734 0.420,0.161 10 CANL 2.461,1.289 1.948,0.646 false 3.484,2.23 3.890,2.379 0.406,0.149 10 GND1 4.413,2.218 4.730,2.379 0.317,0.161 10 +BS 3.973,1.43 3.677,2.21 false 4.24,1.429 4.537,2.209 false

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A22 brake actuator assembly (skid control ECU) connector.


c.
U189186E01
1.583,0.587 1.864,0.738 0.281,0.151 10 A22 2.89,2.431 3.324,2.580 0.434,0.149 10 CANH 2.853,0.956 3.287,1.105 0.434,0.149 10 CANL 2.511,1.642 2.826,1.053 false 2.567,1.776 2.872,2.508 false 0.086,0.041 1.962,0.409 1.876,0.368 10 Wire Harness Side: 0.273,0.823 0.706,0.972 0.434,0.149 10 GND1 1.399,1.69 0.788,0.908 false 0.226,2.707 0.660,2.856 0.434,0.149 10 +BS 1.264,1.736 0.607,2.775 false

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (A22-26) - CANL (A22-15) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (A22-26) - GND1 (A22-4) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (A22-15) - GND1 (A22-4) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (A22-26) - +BS (A22-3) B - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (A22-15) - +BS (A22-3) W - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)


HINT:

For vehicles with VSC only.


U189650E02
4.146,0.854 5.26,0.854 false 4.188,0.667 4.698,0.219 4.698,0.219 5.042,0.219 false 2.792,0.677 2.521,0.25 2.521,0.25 2.344,0.25 false 4.406,0.677 5.042,0.458 5.042,0.458 5.448,0.458 false 3.417,0.094 3.771,0.281 0.354,0.188 10 false A35 5.333,0.781 5.74,0.969 0.406,0.188 10 false CANL 5.104,0.135 5.708,0.323 0.604,0.188 10 false CANH 1.927,0.146 2.531,0.333 0.604,0.188 10 false GND1 5.521,0.375 5.927,0.563 0.406,0.188 10 false +BS

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A35 ABS and traction actuator assembly (skid control ECU) connector.


c.
U189689E02
1.646,0.375 0.958,0.969 false 1.042,1.24 1.698,1.979 false 2.75,1.063 3,1.792 false 0.667,0.906 0.865,0.469 false 2.896,0.323 3.208,0.479 0.313,0.156 10 false A35 1.708,0.281 2.135,0.448 0.427,0.167 10 false CANH 1.75,1.906 2.156,2.073 0.406,0.167 10 false CANL 0.083,0.021 1.573,0.219 1.49,0.198 10 false Wire Harness Side: 2.792,1.823 3.271,1.99 0.479,0.167 10 false GND1 0.906,0.365 1.385,0.531 0.479,0.167 10 false +BS

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (A35-26) - CANL (A35-14) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (A35-26) - GND1 (A35-38) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (A35-14) - GND1 (A35-38) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (A35-26) - +BS (A35-25) B - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (A35-14) - +BS (A35-25) W - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK STEERING ANGLE SENSOR


HINT:

For vehicles with VSC or with AFS only.


U190005E01
3.477,0.474 3.815,0.635 0.338,0.161 10 G18 2.481,2.053 2.991,2.215 0.510,0.163 10 CANH 3.223,2.053 3.733,2.215 0.510,0.163 10 CANL 4.429,2.053 4.772,2.202 0.343,0.149 10 ESS 3.828,2.053 4.130,2.195 0.302,0.142 10 BAT 2.958,1.55 2.713,2.008 false 3.113,1.562 3.427,2.008 false 3.958,1.558 3.958,2.022 false 4.099,1.564 4.561,2.026 false

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G18 steering angle sensor connector.


c.
U190009E01
0.098,0.054 1.411,0.259 1.313,0.205 10 Wire Harness Side: 2.684,2.525 3.152,2.674 0.468,0.149 10 CANH 1.91,2.513 2.378,2.662 0.468,0.149 10 CANL 2.412,1.975 2.118,2.485 false 2.603,1.963 2.96,2.492 false 2.242,0.485 2.547,0.630 0.305,0.145 10 G18 1.345,2.718 1.813,2.867 0.468,0.149 10 BAT 1.277,1.976 1.49,2.697 false 1.089,1.977 0.762,2.715 false 0.571,2.725 1.040,2.874 0.468,0.149 10 ESS

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (G18-10) - CANL (G18-9) BR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (G18-10) - ESS (G18-2) BR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (G18-9) - ESS (G18-2) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (G18-10) - BAT (G18-3) BR - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (G18-9) - BAT (G18-3) W - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK YAW RATE SENSOR


HINT:

For vehicles with VSC only.


U189513E02
1.792,1.625 1.115,2.24 false 2.302,1.625 2.865,2.313 false 5.677,1.708 5.969,2.073 false 1.979,1.375 1.302,0.938 false 2.063,0.719 2.344,0.865 0.281,0.146 10 false N21 2.698,2.323 3.135,2.5 0.438,0.177 10 false CANH 0.885,0.823 1.323,1 0.438,0.177 10 false CANL 0.906,2.25 1.354,2.396 0.448,0.146 10 false GNDA 4.979,0.719 5.26,0.865 0.281,0.146 10 false G15 5.958,2.083 6.25,2.25 0.292,0.167 10 false BAT

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the N21 yaw rate sensor connector.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (N21-2) - CANL (N21-3) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (N21-2) - GNDA (N21-4) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (N21-3) - GNDA (N21-4) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (N21-2) - BAT (G15-16) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (N21-3) - BAT (G15-16) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER


U189003E02
3.781,1.302 4.354,2.344 false 4.781,1.406 4.948,2.344 false 3.677,1.292 3.677,2.323 false 3.49,1.302 2.969,2.354 false 3.823,0.417 4.125,0.583 0.302,0.167 10 false G47 4.125,2.354 4.615,2.521 0.49,0.167 10 false CANH 3.51,2.354 4,2.521 0.49,0.167 10 false CANL 2.802,2.365 3.198,2.573 0.396,0.208 10 false GND 4.938,2.375 5.104,2.604 0.167,0.229 10 false B

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G47 air conditioning amplifier connector.


c.
U189294E02
1.938,2.042 2.281,2.667 false 1.771,2.042 1.5,2.677 false 2.188,1.958 2.677,1.375 false 0.542,2.167 0.375,2.677 false 0.146,0.146 1.438,0.344 1.292,0.198 10 false Wire Harness Side: 1.604,1.135 1.917,1.333 0.313,0.198 10 false G47 1.271,2.698 1.708,2.885 0.438,0.188 10 false CANH 2.198,2.677 2.625,2.865 0.427,0.188 10 false CANL 2.719,1.302 3.115,1.51 0.396,0.208 10 false GND 0.323,2.698 0.635,2.885 0.313,0.188 10 false B

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (G47-11) - CANL (G47-12) V - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (G47-11) - GND (G47-14) V - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (G47-12) - GND (G47-14) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (G47-11) - B (G47-21) V - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (G47-12) - B (G47-21) W - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 2AZ-FE)


U188992E02
4.594,1.698 4.156,2.344 false 4.594,1.844 4.656,2.365 false 5.927,1.396 6.302,1.74 false 1.906,1.99 1.646,2.406 false 2.583,0.427 2.917,0.604 0.333,0.177 10 false D2 5.156,0.427 5.49,0.604 0.333,0.177 10 false A7 3.885,2.365 4.458,2.51 0.573,0.146 10 false CANH 4.521,2.396 5.083,2.542 0.563,0.146 10 false CANL 6.354,1.76 6.792,1.948 0.438,0.188 10 false BATT 1.5,2.427 1.708,2.594 0.208,0.167 10 false E1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A7 and D2 ECM connectors.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (A7-41) - CANL (A7-49) B - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
CANH (A7-41) - E1 (D2-104) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (A7-49) - E1 (D2-104) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (A7-41) - BATT (A7-20) B - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (A7-49) - BATT (A7-20) W - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 2GR-FE)


U188991E02
4.583,1.698 4.146,2.344 false 4.604,1.833 4.667,2.354 false 5.958,1.375 6.333,1.719 false 1.917,1.771 1.656,2.396 false 2.594,0.438 2.927,0.615 0.333,0.177 10 false D1 5.156,0.427 5.49,0.604 0.333,0.177 10 false A7 3.865,2.375 4.438,2.521 0.573,0.146 10 false CANH 4.552,2.385 5.115,2.531 0.563,0.146 10 false CANL 6.417,1.74 6.854,1.927 0.438,0.188 10 false BATT 1.51,2.406 1.719,2.573 0.208,0.167 10 false E1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A7 and D1 ECM connectors.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (A7-41) - CANL (A7-49) B - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
CANH (A7-41) - E1 (D1-81) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (A7-49) - E1 (D1-81) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (A7-41) - BATT (A7-20) B - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (A7-49) - BATT (A7-20) W - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CENTER AIRBAG SENSOR ASSEMBLY


U188989E02
1.938,1.771 2.094,2.219 false 4.51,1.615 4.365,2.26 false 4.698,1.917 4.969,2.271 false 4.167,1.948 3.844,2.271 false 1.24,0.698 1.521,0.906 0.281,0.208 10 false G15 4.865,0.563 5.146,0.771 0.281,0.208 10 false G19 2.052,2.26 2.396,2.427 0.344,0.167 10 false BAT 4.198,2.323 4.667,2.49 0.469,0.167 10 false CANH 4.865,2.333 5.333,2.5 0.469,0.167 10 false CANL 3.708,2.313 3.906,2.51 0.198,0.198 10 false E1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G19 center airbag sensor connector.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (G19-13) - CANL (G19-22) Y - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (G19-13) - E1 (G19-25) Y - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (G19-22) - E1 (G19-25) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (G19-13) - BAT (G15-16) Y - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (G19-22) - BAT (G15-16) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER STEERING ECU


U189002E01
3.192,0.483 3.524,0.676 0.332,0.193 10 G91 4.429,0.1 4.761,0.293 0.332,0.193 10 A21 5.968,0.941 6.290,1.129 0.323,0.188 10 PIG 5.968,1.847 6.438,2.040 0.471,0.193 10 PGND 2.408,2.006 2.878,2.171 0.471,0.165 10 CANH 3.279,2.006 3.749,2.171 0.471,0.165 10 CANL 3.597,1.225 2.762,1.94 false 3.61,1.349 3.481,1.959 false 4.651,1.296 5.902,1.044 false 4.641,1.8 5.865,1.912 false

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A21 and G91 power steering ECU connectors.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (G91-1) - CANL (G91-7) Y - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (G91-1) - PGND (A21-2) Y - W Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (G91-7) - PGND (A21-2) W - W Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (G91-1) - PIG (A21-1) Y - B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (G91-7) - PIG (A21-1) W - B Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY (COMBINATION METER ECU)


U189004E01
3.418,0.316 3.777,0.499 0.360,0.184 10 G28 2.496,2.108 2.976,2.273 0.480,0.165 10 CANH 3.139,2.108 3.618,2.273 0.480,0.165 10 CANL 1.985,2.108 2.206,2.255 0.221,0.147 10 EP 5.228,2.108 5.384,2.283 0.156,0.174 10 B 3.22,1.501 2.138,2.08 false 3.367,1.501 2.801,2.043 false 3.525,1.494 3.392,2.074 false 4.834,1.507 5.258,2.092 false 1.246,0.834 1.701,1.000 0.455,0.166 10 MPX+ 1.284,1.481 1.738,1.647 0.455,0.166 10 MPX- 1.676,0.907 2.467,1.171 false 1.662,1.536 2.32,1.268 false

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G28 combination meter assembly (combination meter ECU) connector.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (G28-32) - CANL (G28-31) B - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
CANH (G28-32) - EP (G28-33) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (G28-31) - EP (G28-33) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (G28-32) - B (G28-22) B - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (G28-31) - B (G28-22) W - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
MPX+ (G28-18) - MPX- (G28-19) LG - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
MPX+ (G28-18) - EP (G28-33) LG - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
MPX- (G28-19) - EP (G28-33) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
MPX+ (G28-18) - B (G28-22) LG - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
MPX- (G28-19) - B (G28-22) W - W Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)


C367456E01
1.042,4.417 1.458,4.667 0.417,0.25 3.75,4.417 4.167,4.667 0.417,0.25 1.51,5.313 1.844,5.052 false 4.177,5.26 4.51,4.729 false 3.167,5.969 3.708,5.604 false 3.719,6.083 3.813,5.604 false 4.271,6.135 4.104,5.479 false 4.719,5.948 4.198,5.479 false 1.156,4.458 1.583,4.708 0.427,0.25 10 false 4K 1.896,4.917 2.375,5.167 0.479,0.25 10 false BECU 3.823,4.458 4.25,4.708 0.427,0.25 10 false G59 4.51,4.563 4.938,4.813 0.427,0.25 10 false GND1 4.625,5.969 5.052,6.219 0.427,0.25 10 false CANH 4.125,6.167 4.552,6.417 0.427,0.25 10 false CANL 3.521,6.125 3.948,6.375 0.427,0.25 10 false CANN 2.875,5.99 3.302,6.24 0.427,0.25 10 false CANP 5.875,2.344 6.302,2.594 0.427,0.25 10 false 4K 6.26,2.406 6.688,2.656 0.427,0.25 10 false G59

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G59 and 4K main body ECU (instrument panel junction block LH) connectors.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (G59-5) - CANL (G59-6) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (G59-5) - GND1 (G59-1) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (G59-6) - GND1 (G59-1) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (G59-5) - BECU (4K-1) B - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (G59-6) - BECU (4K-1) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANP (G59-16) - CANN (G59-15) B - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
CANP (G59-16) - GND1 (G59-1) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANN (G59-15) - GND1 (G59-1) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANP (G59-16) - BECU (4K-1) B - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANN (G59-15) - BECU (4K-1) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NETWORK GATEWAY ECU (for RHD)


U189515E01
1.86,0.798 2.144,0.947 0.284,0.149 10 G40 0.926,1.868 1.332,2.010 0.406,0.142 10 CA1H 1.375,2.118 1.780,2.260 0.406,0.142 10 CA1L 1.982,2.118 2.388,2.260 0.406,0.142 10 CA2H 2.432,1.889 2.838,2.031 0.406,0.142 10 CA2L 1.611,1.458 1.129,1.868 false 1.71,1.469 1.554,2.106 false 1.872,1.459 2.166,2.118 false 1.977,1.46 2.596,1.875 false 1.106,0.812 1.447,0.954 0.341,0.142 10 GND 1.701,1.292 1.456,0.883 false 5.109,0.756 5.393,0.905 0.284,0.149 10 G15 5.623,1.982 6.029,2.124 0.406,0.142 10 BAT 5.763,1.65 5.763,1.977 false

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G40 network gateway ECU connector.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CA1H (G40-16) - CA1L (G40-15) G - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CA1H (G40-16) - GND (G40-4) G - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CA1L (G40-15) - GND (G40-4) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CA1H (G40-16) - BAT (G15-16) G - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CA1L (G40-15) - BAT (G15-16) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CA2H (G40-13) - CA2L (G40-12) V - P Cable disconnected from negative (-) battery terminal 108 to 132 Ω
CA2H (G40-13) - GND (G40-4) V - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CA2L (G40-12) - GND (G40-4) P - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CA2H (G40-13) - BAT (G15-16) V - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CA2L (G40-12) - BAT (G15-16) P - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AFS ECU


HINT:

For vehicles with AFS only.


U189189E01
5.087,0.642 5.384,0.793 0.297,0.151 10 G15 1.902,0.675 2.199,0.826 0.297,0.151 10 A28 6.129,1.915 6.442,2.071 0.313,0.156 10 BAT 5.767,1.644 6.094,1.971 false 0.701,0.523 1.100,0.679 0.399,0.156 10 CAN+ 0.249,0.716 0.613,0.871 0.364,0.156 10 CAN- 2.465,1.843 2.677,1.999 0.211,0.156 10 E1 1.246,1.214 1.106,0.612 false 1.129,1.214 0.616,0.794 false 2.122,1.42 2.451,1.91 false

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A28 AFS ECU connector.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CAN+ (A28-12) - CAN- (A28-13) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CAN+ (A28-12) - E1 (A28-22) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CAN- (A28-13) - E1 (A28-22) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CAN+ (A28-12) - BAT (G15-16) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CAN- (A28-13) - BAT (G15-16) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NAVIGATION RECEIVER ASSEMBLY


HINT:

For vehicles with navigation system only.


U189571E02
1.844,0.552 2.01,0.552 2.01,0.552 2.01,1.688 false 2.313,0.563 2.094,0.563 2.094,0.563 2.094,1.698 false 5.792,0.531 5.625,0.531 5.625,0.531 5.625,1.51 false 5.188,2.271 5.021,2.271 5.021,2.271 5.021,1.875 false 2.375,0.479 2.813,0.656 0.438,0.177 10 false CANL 1.385,0.49 1.823,0.667 0.438,0.177 10 false CANH 5.896,0.438 6.198,0.615 0.302,0.177 10 false +B 5.24,2.188 5.688,2.375 0.448,0.188 10 false GND 0.677,1.563 1,1.74 0.323,0.177 10 false F17 3.938,1.552 4.26,1.729 0.323,0.177 10 false F13

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F17 and F13 navigation receiver assembly connectors.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (F17-9) - CANL (F17-10) SB - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (F17-9) - GND (F13-7) SB - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (F17-10) - GND (F13-7) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (F17-9) - +B (F13-4) SB - Y Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (F17-10) - +B (F13-4) W - Y Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER SLIDE DOOR ECU LH


HINT:

For vehicles with power slide door system only.


U189205E01
2.526,0.542 2.825,0.702 0.299,0.161 10 M22 3.895,0.514 4.246,0.670 0.350,0.156 10 GND 3.469,1.277 3.877,0.586 false 1.484,0.542 1.902,0.691 0.417,0.149 10 MPX2 2.724,2.106 3.141,2.255 0.417,0.149 10 MPX1 2.429,1.642 2.694,2.16 false 1.052,2.097 1.467,2.234 0.415,0.137 10 ECUB 1.994,1.612 1.474,2.152 false

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M22 power slide door ECU LH connector.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
MPX1 (M22-11) - MPX2 (M22-5) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
MPX1 (M22-11) - GND (M22-1) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
MPX2 (M22-5) - GND (M22-1) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
MPX1 (M22-11) - ECUB (M22-12) B - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
MPX2 (M22-5) - ECUB (M22-12) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER SLIDE DOOR ECU RH


HINT:

For vehicles with power slide door system only.


U189200E01
4.248,0.574 4.557,0.758 0.309,0.184 10 N24 4.047,2.079 4.453,2.229 0.406,0.150 10 MPX1 5.454,0.646 5.860,0.797 0.406,0.150 10 MPX2 3.087,0.609 3.423,0.759 0.336,0.150 10 GND 5.501,2.076 5.906,2.226 0.406,0.150 10 ECUB 4.836,1.377 5.391,0.711 false 4.776,1.612 4.457,2.126 false 3.695,1.282 3.409,0.687 false 5.132,1.663 5.452,2.14 false

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the N24 power slide door ECU RH connector.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
MPX1 (N24-8) - MPX2 (N24-2) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
MPX1 (N24-8) - GND (N24-6) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
MPX2 (N24-2) - GND (N24-6) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
MPX1 (N24-8) - ECUB (N24-7) B - LG Cable disconnected from negative (-) battery terminal 6 kΩ or higher
MPX2 (N24-2) - ECUB (N24-7) W - LG Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER BACK DOOR ECU


HINT:

For vehicles with power back door system only.


U189199E01
3.455,0.459 3.743,0.615 0.288,0.156 10 M24 4.31,2.057 4.706,2.222 0.397,0.165 10 MPX1 5.093,0.573 5.490,0.738 0.397,0.165 10 MPX2 0.831,0.559 1.172,0.724 0.341,0.165 10 GND 1.619,2.066 2.044,2.221 0.424,0.156 10 ECUB 2.334,1.23 1.855,1.997 false 1.788,1.174 1.157,0.642 false 3.835,1.255 4.486,2.006 false 4.114,1.17 5.038,0.649 false

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M24 power back door ECU connector.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
MPX1 (M24-6) - MPX2 (M24-5) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
MPX1 (M24-6) - GND (M24-11) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
MPX2 (M24-5) - GND (M24-11) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
MPX1 (M24-6) - ECUB (M24-10) B - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
MPX2 (M24-5) - ECUB (M24-10) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CERTIFICATION ECU


U188568E02
2.104,0.885 1.906,1.438 false 3.823,1.021 3.51,1.427 false 3.979,1.031 4.094,1.427 false 5.25,0.885 5.552,1.375 false 3.469,0.219 3.833,0.365 0.365,0.146 10 false G29 3.906,1.438 4.406,1.604 0.5,0.167 10 false CANH 3.26,1.438 3.76,1.604 0.5,0.167 10 false CANL 5.5,1.406 5.729,1.573 0.229,0.167 10 false +B 1.833,1.448 2,1.635 0.167,0.188 10 false E

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G29 certification ECU connector.


c.

Measure the resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Condition Specified Condition
CANH (G29-27) - CANL (G29-28) SB - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
CANH (G29-27) - E (G29-17) SB- W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANL (G29-28) - E (G29-17) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
CANH (G29-27) - +B (G29-1) SB - BE Cable disconnected from negative (-) battery terminal 6 kΩ or higher
CANL (G29-28) - +B (G29-1) W - BE Cable disconnected from negative (-) battery terminal 6 kΩ or higher