Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  B1216  Rear Door ECU RH Communication Stop  


DESCRIPTION

DTC No. Symptom Trouble Area
B1216 When either condition below is met:
·

Rear Right Door is not displayed on "BUS CHECK" screen of intelligent tester.

·

Applies to "POWER SLIDE DOOR ECU RH COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE".


·

Power source circuit of power slide door ECU RH

·

Power slide door ECU RH branch wire and connector

·

Power slide door ECU RH



HINT:

For vehicles with power slide door system only.


WIRING DIAGRAM

C129192E81
0.146,2.594 0.479,2.802 0.333,0.208 10 false N48 5.396,5.906 7.125,6.135 1.729,0.229 10 false Power Slide Door ECU RH 5.073,5.906 5.479,6.104 0.406,0.198 10 false N24 5.854,1.563 6.375,1.729 0.521,0.167 10 false MPX1 5.854,2.031 6.375,2.198 0.521,0.167 10 false MPX2 5.854,4.052 6.094,4.25 0.24,0.198 10 false IG 5.854,4.604 6.323,4.75 0.469,0.146 10 false GND 4.375,3.115 4.896,3.292 0.521,0.177 10 false ECU-B 5.875,3.271 6.396,3.448 0.521,0.177 10 false ECUB 4.25,3.906 5.01,4.083 0.76,0.177 10 false RH ECU-IG 1.74,5.063 2.573,5.26 0.833,0.198 10 false from Battery 2.781,5.073 4.083,5.271 1.302,0.198 10 false from RH-IG Relay 1 1.552,1.896 1.771,2.042 0.219,0.146 10 false 11 1.542,1.458 1.833,1.604 0.292,0.146 10 false 12 5.552,1.469 5.708,1.625 0.156,0.156 10 false 8 5.552,1.896 5.708,2.052 0.156,0.156 10 false 2 5.542,3.146 5.698,3.302 0.156,0.156 10 false 7 5.542,3.948 5.698,4.104 0.156,0.156 10 false 3 5.542,4.5 5.698,4.656 0.156,0.156 10 false 6 0.469,2.594 2.125,2.792 1.656,0.198 10 false No. 2 Junction Connector

PROCEDURE

1.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Clear the DTC.


d.

Check for DTC.

Result
Result Proceed to
DTC B1216 is not output A
DTC B1216 is output B



A

2.CHECK CAN BUS LINE FOR DISCONNECTION (POWER SLIDE DOOR ECU RH BRANCH WIRE)

B

GO TO POWER SLIDE DOOR SYSTEM

2.CHECK CAN BUS LINE FOR DISCONNECTION (POWER SLIDE DOOR ECU RH BRANCH WIRE)
a.
U189203E01
1.603,0.87 1.891,1.029 0.288,0.159 10 N24 0.657,2.206 1.060,2.359 0.402,0.152 10 MPX1 0.468,0.961 0.871,1.113 0.402,0.152 10 MPX2 1.453,1.584 0.98,1.037 false 1.482,1.862 1.186,2.266 false 0.146,0.105 1.635,0.300 1.489,0.195 10 Wire Harness Side:

Disconnect the N24 power slide door ECU RH connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
N24-8 (MPX1) - N24-2 (MPX2) Engine switch off 54 to 69 Ω




OK

3.CHECK WIRE HARNESS (POWER SLIDE DOOR ECU RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER SLIDE DOOR ECU RH (MPX1, MPX2)

3.CHECK WIRE HARNESS (POWER SLIDE DOOR ECU RH - BATTERY AND BODY GROUND)
a.
U189204E01
1.564,0.827 1.841,0.969 0.277,0.142 10 N24 2.638,1.226 2.982,1.368 0.343,0.142 10 GND 2.217,1.458 2.612,1.304 false 0.477,2.176 0.886,2.318 0.409,0.142 10 ECUB 1.255,1.824 0.981,2.249 false 0.847,1.024 1.024,1.166 0.177,0.142 10 IG 1.603,1.596 1.09,1.099 false 0.153,0.078 1.643,0.274 1.489,0.195 10 Wire Harness Side:

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
N24-6 (GND) - Body ground Below 1 Ω



b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
N24-7 (ECUB) - Body ground Always 10 to 14 V
N24-3 (IG) - Body ground Engine switch on (IG) 10 to 14 V




OK

REPLACE POWER SLIDE DOOR ECU RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR