Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  B1217  Rear Door ECU LH Communication Stop  


DESCRIPTION

DTC No. Symptom Trouble Area
B1217 When either condition below is met:
·

Rear Left Door is not displayed on "BUS CHECK" screen of intelligent tester.

·

Applies to "POWER SLIDE DOOR ECU LH COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE".


·

Power source circuit of power slide door ECU LH

·

Power slide door ECU LH branch wire and connector

·

Power slide door ECU LH



HINT:

For vehicles with power slide door system only.


WIRING DIAGRAM

C129192E83
0.188,2.594 0.583,2.771 0.396,0.177 10 false M48 5.448,5.906 7.135,6.104 1.688,0.198 10 false Power Slide Door ECU LH 5.104,5.906 5.448,6.094 0.344,0.188 10 false M22 5.854,1.563 6.375,1.729 0.521,0.167 10 false MPX1 5.854,2.021 6.375,2.188 0.521,0.167 10 false MPX2 5.854,4.073 6.094,4.271 0.24,0.198 10 false IG 5.854,4.625 6.323,4.771 0.469,0.146 10 false GND 4.375,3.104 4.896,3.281 0.521,0.177 10 false ECU-B 5.885,3.26 6.406,3.438 0.521,0.177 10 false ECUB 4.25,3.885 5.01,4.063 0.76,0.177 10 false LH ECU-IG 1.74,5.094 2.573,5.292 0.833,0.198 10 false from Battery 2.781,5.094 4.083,5.292 1.302,0.198 10 false from LH-IG Relay 1 1.552,1.458 1.708,1.604 0.156,0.146 10 false 3 1.531,1.896 1.729,2.042 0.198,0.146 10 false 11 5.479,1.427 5.688,1.615 0.208,0.188 10 false 11 5.51,1.865 5.719,2.052 0.208,0.188 10 false 5 5.521,3.135 5.729,3.323 0.208,0.188 10 false 12 5.583,3.927 5.792,4.115 0.208,0.188 10 false 4 5.604,4.49 5.813,4.677 0.208,0.188 10 false 1 0.573,2.594 2.271,2.802 1.698,0.208 10 false No. 3 Junction Connector

PROCEDURE

1.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Clear the DTC.


d.

Check for DTC.

Result
Result Proceed to
DTC B1217 is not output A
DTC B1217 is output B



A

2.CHECK CAN BUS LINE FOR DISCONNECTION (POWER SLIDE DOOR ECU LH BRANCH WIRE)

B

GO TO POWER SLIDE DOOR SYSTEM

2.CHECK CAN BUS LINE FOR DISCONNECTION (POWER SLIDE DOOR ECU LH BRANCH WIRE)
a.
U189208E01
1.564,0.874 1.871,1.014 0.307,0.140 10 M22 2.32,2.357 2.733,2.519 0.413,0.163 10 MPX1 1.955,1.935 2.282,2.428 false 2.378,0.973 2.790,1.136 0.413,0.163 10 MPX2 1.979,1.619 2.342,1.065 false 0.09,0.093 1.580,0.289 1.489,0.195 10 Wire Harness Side:

Disconnect the M22 power slide door ECU LH connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
M22-11 (MPX1) - M22-5 (MPX2) Engine switch off 54 to 69 Ω




OK

3.CHECK WIRE HARNESS (POWER SLIDE DOOR ECU LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER SLIDE DOOR ECU LH (MPX1, MPX2)

3.CHECK WIRE HARNESS (POWER SLIDE DOOR ECU LH - BATTERY AND BODY GROUND)
a.
U189209E01
1.573,0.874 1.864,1.020 0.291,0.145 10 M22 0.559,1.037 0.902,1.179 0.343,0.142 10 GND 1.3,1.476 0.962,1.138 false 2.527,2.198 2.953,2.346 0.427,0.149 10 ECUB 2.157,1.897 2.492,2.266 false 2.595,1.042 2.765,1.184 0.170,0.142 10 IG 1.839,1.63 2.552,1.123 false 0.138,0.134 1.627,0.330 1.489,0.195 10 Wire Harness Side:

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
M22-1 (GND) - Body ground Below 1 Ω



b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
M22-12 (ECUB) - Body ground Always 10 to 14 V
M22-4 (IG) - Body ground Engine switch on (IG) 10 to 14 V




OK

REPLACE POWER SLIDE DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR