Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2013.04–2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  B1287  Back Door ECU Communication Stop  


DESCRIPTION

DTC No. Symptom Trouble Area
B1287 When either condition below is met:
·

Power Back Door is not displayed on "Communication Bus Check" screen of intelligent tester.

·

Applies to "POWER BACK DOOR ECU COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE".


·

Power source circuit of power back door ECU

·

Power back door ECU branch wire and connector

·

Power back door ECU



HINT:

For vehicles with power back door system only.


WIRING DIAGRAM

C129192E84
0.25,2.76 1.969,3.177 1.719,0.417 10 false No. 3 Junction Connector 5.406,6.01 6.927,6.458 1.521,0.448 10 false Power Back Door ECU 5.854,1.552 6.375,1.719 0.521,0.167 10 false MPX1 5.854,2.021 6.375,2.188 0.521,0.167 10 false MPX2 5.854,4.042 6.094,4.24 0.24,0.198 10 false IG 5.854,4.625 6.323,4.771 0.469,0.146 10 false GND 4.375,3.083 4.896,3.26 0.521,0.177 10 false ECU-B 5.854,3.26 6.375,3.438 0.521,0.177 10 false ECUB 4.25,3.865 5.01,4.042 0.76,0.177 10 false LH ECU-IG 1.74,5.083 2.573,5.281 0.833,0.198 10 false from Battery 2.781,5.083 4.083,5.281 1.302,0.198 10 false from LH-IG Relay 1 1.552,1.479 1.802,1.625 0.25,0.146 10 false 8 1.552,1.917 1.802,2.063 0.25,0.146 10 false 4 5.573,1.49 5.729,1.646 0.156,0.156 10 false 6 5.583,1.917 5.74,2.073 0.156,0.156 10 false 5 5.521,3.167 5.719,3.323 0.198,0.156 10 false 10 5.583,3.969 5.74,4.125 0.156,0.156 10 false 8 5.521,4.521 5.698,4.688 0.177,0.167 10 false 11 5.406,5.844 5.875,5.99 0.469,0.146 10 false M24 0.25,2.594 0.771,2.771 0.521,0.177 10 false M25

PROCEDURE

1.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG).


c.

Clear the DTC.


d.

Check for DTC.

Result
Result Proceed to
DTC B1287 is not output A
DTC B1287 is output B



A

2.CHECK CAN BUS LINE FOR DISCONNECTION (POWER BACK DOOR ECU BRANCH WIRE)

B

GO TO POWER BACK DOOR SYSTEM

2.CHECK CAN BUS LINE FOR DISCONNECTION (POWER BACK DOOR ECU BRANCH WIRE)
a.
U189210E01
1.56,0.658 1.868,0.800 0.309,0.142 10 M24 1.944,2.46 2.340,2.616 0.397,0.156 10 MPX1 0.632,2.451 1.028,2.607 0.397,0.156 10 MPX2 1.52,1.824 0.884,2.415 false 1.697,1.818 2.172,2.436 false

Disconnect the M24 power back door ECU connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
M24-6 (MPX1) - M24-5 (MPX2) Ignition switch off 54 to 69 Ω




OK

3.CHECK WIRE HARNESS (POWER BACK DOOR ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (MPX1, MPX2)

3.CHECK WIRE HARNESS (POWER BACK DOOR ECU - BATTERY AND BODY GROUND)
a.
U189211E01
1.547,0.724 1.848,0.876 0.302,0.152 10 M24 2.982,1.583 3.318,1.725 0.336,0.142 10 GND 2.746,0.947 3.162,1.103 0.416,0.156 10 ECUB 1.431,2.391 1.614,2.536 0.184,0.145 10 IG 2.223,1.617 2.707,1.059 false 2.492,1.723 2.947,1.65 false 1.876,1.832 1.533,2.351 false

Disconnect the M24 power back door ECU connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
M24-11 (GND) - Body ground Below 1 Ω



c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
M24-10 (ECUB) - Body ground Always 10 to 14 V
M24-8 (IG) - Body ground Ignition switch on (IG) 10 to 14 V




OK

REPLACE POWER BACK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR