Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

If 2 or more DTCs are output during the BUS CHECK, one side of the CAN branch wire may be open. (One side of the CANH [branch wire] /CANL [branch wire] of the ECU and/or sensor is open.)

Detection Item Symptom Trouble Area
STEERING ANGLE SENSOR COMMUNICATION STOP MODE When either condition below is met:
·

Steering Angle Sensor is not displayed on "BUS CHECK" screen of intelligent tester

·

Applies to "STEERING ANGLE SENSOR COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE"


·

Power source or inside steering angle sensor

·

One side of CAN branch wire

·

Steering angle sensor branch wire and connector

·

Steering angle sensor



For vehicles with VSC or with AFS only.

WIRING DIAGRAM

C129192E73
0.081,2.486 0.413,2.657 0.332,0.172 10 G72 0.083,2.644 2.586,2.973 2.503,0.328 10 No. 2 CAN Junction Connector LH 5.449,5.781 6.925,5.974 1.475,0.193 10 G18 5.456,5.934 6.931,6.172 1.475,0.238 10 Steering Angle Sensor 5.846,1.487 6.344,1.680 0.498,0.193 10 CANH 5.846,1.937 6.344,2.130 0.498,0.193 10 CANL 5.846,3.174 6.169,3.359 0.323,0.184 10 BAT 5.846,3.977 6.096,4.168 0.250,0.191 10 IG 5.846,4.548 6.183,4.718 0.337,0.170 10 ESS 4.389,2.988 4.999,3.163 0.610,0.174 10 ECU-B 4.258,3.801 5.007,3.975 0.748,0.174 10 RH ECU-IG 1.691,4.968 2.689,5.152 0.998,0.184 10 from Battery 2.765,4.95 4.023,5.133 1.258,0.184 10 from RH-IG Relay 1 1.54,1.419 1.704,1.582 0.163,0.163 10 1 1.545,1.863 1.727,2.026 0.181,0.163 10 2 5.505,1.419 5.724,1.587 0.218,0.167 10 10 5.557,1.854 5.701,2.017 0.145,0.164 10 9 5.58,3.1 5.676,3.256 0.096,0.155 10 3 5.586,3.905 5.712,4.072 0.126,0.167 10 1 5.6,4.455 5.706,4.622 0.106,0.167 10 2 0.09,0 0.770,0.218 0.679,0.218 12 for LHD:

C129192E72
0.081,2.646 2.409,3.036 2.327,0.390 10 No. 4 Junction Connector 0.074,2.463 0.501,2.635 0.427,0.173 10 G104 5.449,5.781 6.925,5.974 1.475,0.193 10 G18 5.456,5.934 6.931,6.172 1.475,0.238 10 Steering Angle Sensor 5.846,1.487 6.344,1.680 0.498,0.193 10 CANH 5.846,1.937 6.344,2.130 0.498,0.193 10 CANL 5.846,3.174 6.169,3.359 0.323,0.184 10 BAT 5.846,3.977 6.096,4.168 0.250,0.191 10 IG 5.846,4.548 6.183,4.718 0.337,0.170 10 ESS 4.389,2.988 4.999,3.163 0.610,0.174 10 ECU-B 4.258,3.801 5.007,3.975 0.748,0.174 10 RH ECU-IG 1.691,4.968 2.689,5.152 0.998,0.184 10 from Battery 2.765,4.95 4.023,5.133 1.258,0.184 10 from RH-IG Relay 1 1.582,1.419 1.746,1.582 0.163,0.163 10 9 1.545,1.863 1.727,2.026 0.181,0.163 10 20 5.505,1.419 5.724,1.587 0.218,0.167 10 10 5.557,1.854 5.701,2.017 0.145,0.164 10 9 5.58,3.1 5.676,3.256 0.096,0.155 10 3 5.586,3.905 5.712,4.072 0.126,0.167 10 1 5.6,4.455 5.706,4.622 0.106,0.167 10 2 0.061,0 1.032,0.429 0.972,0.429 12 for RHD:

CAUTION / NOTICE / HINT

NOTICE:

Turn the engine switch off before measuring the resistances of the main wire and the branch wire.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRES (STEERING ANGLE SENSOR BRANCH WIRE)
a.

Disconnect the G18 steering angle sensor connector.


U190006E02
2.406,1.969 2.115,2.479 false 2.563,1.958 2.927,2.49 false 0.177,0.115 1.521,0.323 1.344,0.208 10 false Wire Harness Side: 2.708,2.51 3.177,2.656 0.469,0.146 10 false CANH 1.896,2.5 2.365,2.646 0.469,0.146 10 false CANL 2.26,0.49 2.563,0.635 0.302,0.146 10 false G18

b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
G18-10 (CANH) - G18-9 (CANL) Engine switch off 54 to 69 Ω




OK

2.CHECK WIRE HARNESS (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

2.CHECK WIRE HARNESS (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.
U190007E01
0.127,0.049 1.565,0.212 1.438,0.163 10 Wire Harness Side: 2.109,0.379 2.438,0.549 0.330,0.170 10 G18 0.554,2.507 0.802,2.661 0.248,0.154 10 IG 1.161,2.507 1.487,2.673 0.326,0.166 10 ESS 1.826,2.507 2.135,2.649 0.309,0.142 10 BAT 0.915,1.956 0.717,2.447 false 1.093,1.948 1.302,2.43 false 1.279,1.949 1.912,2.43 false

Disconnect the G18 steering angle sensor connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G18-2 (ESS) - Body ground Below 1 Ω



c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
G18-3 (BAT) - Body ground Always 11 to 14 V
G18-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

REPLACE STEERING ANGLE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR