Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Yaw Rate Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
YAW RATE SENSOR COMMUNICATION STOP MODE When either condition below is met:
·

Yaw Rate / Deceleration Sensor is not displayed on "BUS CHECK" screen of intelligent tester

·

Applies to "YAW RATE SENSOR COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE"


·

Power source or inside yaw rate sensor

·

Yaw rate sensor branch wire and connector

·

Yaw rate sensor



WIRING DIAGRAM

C129195E20
0.177,2.948 0.49,3.125 0.313,0.177 10 false N48 0.5,2.948 2.51,3.292 2.01,0.344 10 false No. 2 Junction Connector 5.354,5.906 6.521,6.063 1.167,0.156 10 false N21 5.667,5.906 6.833,6.26 1.167,0.354 10 false Yaw Rate Sensor 5.906,1.927 6.417,2.104 0.51,0.177 10 false CANH 5.906,2.365 6.417,2.542 0.51,0.177 10 false CANL 5.906,3.656 6.198,3.823 0.292,0.167 10 false IGA 5.917,4.615 6.375,4.771 0.458,0.156 10 false GNDA 4.25,3.5 5.042,3.677 0.792,0.177 10 false RH ECU-IG 1.51,5.396 2.781,5.604 1.271,0.208 10 false from RH-IG Relay 1 1.552,1.823 1.698,2.021 0.146,0.198 10 false 2 1.552,2.271 1.698,2.469 0.146,0.198 10 false 7 5.594,2.26 5.74,2.406 0.146,0.146 10 false 3 5.594,3.552 5.74,3.698 0.146,0.146 10 false 1 5.594,4.51 5.74,4.656 0.146,0.146 10 false 4 5.594,1.833 5.74,1.979 0.146,0.146 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Turn the engine switch off before measuring the resistances of the main wire and the branch wire.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK CAN BUS LINE FOR DISCONNECTION (YAW RATE SENSOR BRANCH WIRE)
a.

Disconnect the N21 yaw rate sensor connector.


U189517E02
1.781,1.854 2.115,2.406 false 1.5,1.625 0.865,1.135 false 1.5,0.917 1.813,1.073 0.313,0.156 10 false N21 2.156,2.396 2.583,2.563 0.427,0.167 10 false CANH 0.458,1.021 0.865,1.188 0.406,0.167 10 false CANL 0.115,0.073 1.604,0.271 1.49,0.198 10 false Wire Harness Side:

b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
N21-2 (CANH) - N21-3 (CANL) Engine switch off 54 to 69 Ω




OK

2.CHECK WIRE HARNESS (YAW RATE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)

2.CHECK WIRE HARNESS (YAW RATE SENSOR - BATTERY AND BODY GROUND)
a.
U189518E01
1.473,0.878 1.764,1.041 0.291,0.163 10 N21 0.335,2.109 0.783,2.251 0.448,0.142 10 GNDA 2.552,1.092 2.840,1.234 0.288,0.142 10 IGA 2.05,1.596 2.525,1.198 false 1.253,1.845 0.858,2.166 false 0.109,0.105 1.419,0.285 1.310,0.179 10 Wire Harness Side:

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
N21-4 (GNDA) - Body ground Below 1 Ω



b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
N21-1 (IGA) - Body ground Engine switch on (IG) 11 to 14 V




OK

REPLACE YAW RATE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR