Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2013.04–2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
POWER STEERING ECU COMMUNICATION STOP MODE When either condition below is met:
·

EPS is not displayed on "Communication Bus Check" screen of intelligent tester

·

Applies to "POWER STEERING ECU COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE"


·

Power source or inside power steering ECU

·

Power steering ECU branch wire and connector

·

Power steering ECU



WIRING DIAGRAM

C141067E10
0.104,2.688 2.896,2.885 2.792,0.198 10 false No. 2 CAN Junction Connector LH 0.104,2.531 0.51,2.729 0.406,0.198 10 false G69 5.51,5.896 6.917,6.094 1.406,0.198 10 false Power Steering ECU 5.813,1.563 6.302,1.719 0.49,0.156 10 false CANH 5.813,2.01 6.302,2.167 0.49,0.156 10 false CANL 5.813,3.26 6.135,3.458 0.323,0.198 10 false PIG 5.813,4.052 6.052,4.25 0.24,0.198 10 false IG 5.813,4.625 6.313,4.792 0.5,0.167 10 false PGND 4.458,3.083 4.948,3.24 0.49,0.156 10 false EPS 4.198,3.896 4.969,4.042 0.771,0.146 10 false RH ECU-IG 1.656,5.083 2.479,5.292 0.823,0.208 10 false from Battery 2.688,5.083 4.042,5.25 1.354,0.167 10 false from RH-IG Relay 1 0.094,0.125 1.292,0.469 1.198,0.344 12 false for LHD: 5.552,1.385 5.667,1.531 0.115,0.146 10 false 1 5.552,1.833 5.667,1.979 0.115,0.146 10 false 7 5.552,3.073 5.667,3.219 0.115,0.146 10 false 1 5.552,3.875 5.667,4.021 0.115,0.146 10 false 6 5.552,4.427 5.667,4.573 0.115,0.146 10 false 2 5.448,1.583 5.75,1.75 0.302,0.167 10 false G91 5.448,2.021 5.75,2.188 0.302,0.167 10 false G91 5.458,3.271 5.76,3.438 0.302,0.167 10 false A21 5.448,4.063 5.75,4.229 0.302,0.167 10 false G91 5.458,4.625 5.76,4.792 0.302,0.167 10 false A21 1.542,1.469 1.708,1.635 0.167,0.167 10 false 1 1.552,1.896 1.719,2.063 0.167,0.167 10 false 2

C141067E11
0.188,2.594 2.802,2.792 2.615,0.198 10 false G103 0.188,2.76 2.802,2.958 2.615,0.198 10 false No. 5 Junction Connector 5.51,5.906 6.917,6.104 1.406,0.198 10 false Power Steering ECU 5.813,1.573 6.302,1.729 0.49,0.156 10 false CANH 5.813,2.031 6.302,2.188 0.49,0.156 10 false CANL 5.813,3.271 6.135,3.469 0.323,0.198 10 false PIG 5.813,4.063 6.052,4.26 0.24,0.198 10 false IG 5.813,4.615 6.313,4.781 0.5,0.167 10 false PGND 4.469,3.094 4.958,3.25 0.49,0.156 10 false EPS 4.219,3.885 4.99,4.031 0.771,0.146 10 false RH ECU-IG 1.656,5.083 2.479,5.292 0.823,0.208 10 false from Battery 2.688,5.083 4.042,5.25 1.354,0.167 10 false from RH-IG Relay 1 0.125,0.094 0.979,0.458 0.854,0.365 12 false for RHD: 5.552,1.406 5.667,1.552 0.115,0.146 10 false 1 5.552,1.833 5.667,1.979 0.115,0.146 10 false 7 5.552,3.073 5.667,3.219 0.115,0.146 10 false 1 5.552,3.875 5.667,4.021 0.115,0.146 10 false 6 5.531,4.448 5.646,4.594 0.115,0.146 10 false 2 5.448,1.583 5.75,1.75 0.302,0.167 10 false G91 5.438,2.021 5.74,2.188 0.302,0.167 10 false G91 5.458,3.271 5.76,3.438 0.302,0.167 10 false A21 5.448,4.073 5.75,4.24 0.302,0.167 10 false G91 5.448,4.625 5.75,4.792 0.302,0.167 10 false A21 1.542,1.469 1.771,1.635 0.229,0.167 10 false 10 1.552,1.896 1.771,2.063 0.219,0.167 10 false 21

CAUTION / NOTICE / HINT

NOTICE:

Turn the engine switch off before measuring the resistances of the main wire and the branch wire.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRES (POWER STEERING ECU BRANCH WIRE)
a.
U188997E01
0.163,0.088 1.520,0.251 1.357,0.163 10 Wire Harness Side: 1.594,0.799 1.880,0.980 0.287,0.180 10 G91 0.486,2.701 0.962,2.864 0.475,0.163 10 CANH 1.734,2.713 2.209,2.876 0.475,0.163 10 CANL 1.229,1.932 0.75,2.641 false 1.296,2.208 1.763,2.684 false

Disconnect the G91 power steering ECU connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
G91-1 (CANH) - G91-7 (CANL) Engine switch off 54 to 69 Ω




OK

2.CHECK WIRE HARNESS (POWER STEERING ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU (CANH, CANL)

2.CHECK WIRE HARNESS (POWER STEERING ECU - BATTERY AND BODY GROUND)
a.
C366243E01
1.5,0.417 1.917,0.667 0.417,0.25 1.417,2.75 1.833,3 0.417,0.25 1.188,1.74 1.604,1.49 false 1.885,1.938 2.354,2.073 false 2.25,3.771 2.667,4.083 false 0.083,0.094 1.438,0.417 1.354,0.323 10 false Wire Harness Side: 1.573,0.448 2.26,0.781 0.688,0.333 10 false A21 0.896,1.677 1.583,2.01 0.688,0.333 10 false PIG 2.396,2.021 3.083,2.354 0.688,0.333 10 false PGND 1.49,2.792 2.177,3.125 0.688,0.333 10 false G91 2.677,4.104 3.042,4.354 0.365,0.25 10 false IG

Disconnect the A21 and G91 power steering ECU connectors.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A21-2 (PGND) - Body ground Below 1 Ω



c.

Measure the voltage of the wire harness side connectors.

Standard voltage:
Tester Connection Condition Specified Condition
A21-1 (PIG) - Body ground Always 11 to 14 V
G91-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

REPLACE POWER STEERING ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR