There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. | ·
Short between CAN bus lines ·
Brake actuator assembly (skid control ECU)*1 ·
ABS and traction actuator (skid control ECU)*2 ·
Power steering ECU ·
Yaw rate sensor*2 ·
ECM ·
Center airbag sensor assembly ·
Air conditioning amplifier ·
Combination meter assembly (Combination meter ECU) ·
Instrument panel junction block (Main body ECU) ·
Navigation receiver assembly*3 ·
AFS ECU*4 ·
Steering angle sensor*5 ·
No. 1 junction connector ·
No. 2 CAN junction connector LH ·
No. 1 CAN junction connector RH ·
No. 2 junction connector |
*1: w/o VSC
*2: w/ VSC
*3: w/ Navigation system
*4: w/ AFS
*5: w/ VSC or w/ AFS
Turn the engine switch off before measuring the resistances of the main wire and the branch wire.
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Disconnect the G70 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Reconnect the G70 No. 2 CAN junction connector LH.
NEXT
Disconnect the A29 No. 1 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
NG
OK
Disconnect the G74 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
NG
OK
Reconnect the A29 No. 1 junction connector.
Reconnect the G74 No. 2 CAN junction connector LH.
NEXT
Disconnect the G78 No. 1 CAN junction connector RH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Reconnect the G78 No. 1 CAN junction connector RH.
NEXT
Disconnect the N35 No. 2 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
NG
OK
Disconnect the G79 No. 1 CAN junction connector RH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
NG
OK
Reconnect the N35 No. 2 junction connector.
Reconnect the G79 No. 1 CAN junction connector RH.
NEXT
For vehicles without AFS, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 CAN JUNCTION CONNECTOR RH - AIR CONDITIONING AMPLIFIER)".
Disconnect the G95 No. 1 CAN junction connector RH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the A28 AFS ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G95-1 (CANH) - G95-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the G77 No. 1 CAN junction connector RH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the G47 air conditioning amplifier connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-1 (CANH) - G77-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
For vehicles with VSC, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR)".
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-1 (CANH) - A29-5 (CANL) | Engine switch off | 200 Ω or higher |
OK
NG
For vehicles without VSC, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - ECM)".
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-1 (CANH) - A29-5 (CANL) | Engine switch off | 200 Ω or higher |
OK
NG
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-4 (CANH) - A29-7 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Disconnect the A22 brake actuator assembly (skid control ECU) connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-1 (CANH) - A29-5 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the A35 ABS and traction actuator (skid control ECU) connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-1 (CANH) - A29-5 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the A7 ECM connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-4 (CANH) - A29-7 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Reconnect the G78 No. 1 CAN junction connector RH.
NEXT
Disconnect the G71 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
NG
OK
For vehicles without VSC and AFS, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 CAN JUNCTION CONNECTOR LH - POWER STEERING ECU)".
Disconnect the G72 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
NG
OK
Disconnect the G69 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
NG
OK
Disconnect the G75 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
NG
OK
For vehicles without navigation system, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 CAN JUNCTION CONNECTOR LH - NO. 1 CAN JUNCTION CONNECTOR RH)".
Disconnect the G96 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
NG
OK
Disconnect the G73 No. 2 junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Disconnect the G19 center airbag sensor assembly connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G71-1 (CANH) - G71-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the G18 steering angle sensor connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G72-1 (CANH) - G72-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the G91 power steering ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G69-1 (CANH) - G69-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the G59 main body ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G75-1 (CANH) - G75-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the F17 navigation receiver assembly connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G96-1 (CANH) - G96-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
For vehicles without VSC, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ECU)".
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N35-2 (CANH) - N35-7 (CANL) | Engine switch off | 200 Ω or higher |
OK
NG
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N35-3 (CANH) - N35-8 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Disconnect the N21 yaw rate sensor connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N35-2 (CANH) - N35-7 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the G28 combination meter assembly (combination meter ECU) connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N35-3 (CANH) - N35-8 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG