There may be a short circuit between the CAN bus line and GND when there is low resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| There is low resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3. | ·
Short to GND ·
ABS and traction actuator (skid control ECU) ·
Power steering ECU ·
Yaw rate sensor ·
ECM ·
Center airbag sensor assembly ·
Air conditioning amplifier ·
Combination meter assembly (combination meter ECU) ·
Main body ECU ·
Navigation receiver assembly*1 ·
AFS ECU*2 ·
Steering angle sensor ·
No. 1 junction connector ·
No. 2 CAN junction connector LH ·
No. 2 junction connector ·
No. 1 CAN junction connector RH |
*1: w/ Navigation System
*2: w/ AFS
Turn the engine switch off before measuring the resistances of the main wire and the branch wire.
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Disconnect the G131 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 1 MΩ or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 1 MΩ or higher |
OK
NG
Reconnect the G131 No. 2 CAN junction connector LH.
NEXT
Disconnect the A29 No. 1 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
NG
OK
Reconnect the A29 No. 1 junction connector.
NEXT
Disconnect the G78 No. 1 CAN junction connector RH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Reconnect the G78 No. 1 CAN junction connector RH.
NEXT
Disconnect the N48 No. 2 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
NG
OK
Reconnect the N48 No. 2 junction connector.
NEXT
Disconnect the G133 No. 1 CAN junction connector RH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
For vehicles without AFS, go to "CHECK CAN BUS LINE FOR SHORT TO GND (NO. 1 CAN JUNCTION CONNECTOR RH - AIR CONDITIONING AMPLIFIER)".
Disconnect the G95 No. 1 CAN junction connector RH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the A28 AFS ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G95-1 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G95-2 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the G77 No. 1 CAN junction connector RH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the G47 air conditioning amplifier connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-1 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G77-2 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-1 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| A29-5 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-4 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| A29-7 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the A35 ABS and traction actuator (skid control ECU) connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-1 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| A29-5 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the A7 ECM connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-4 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| A29-7 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the G132 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
NG
OK
Disconnect the G72 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
NG
OK
Disconnect the G130 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
NG
OK
For vehicles without navigation system, go to "CHECK CAN BUS LINE FOR SHORT TO GND (NO. 2 CAN JUNCTION CONNECTOR LH - MAIN BODY ECU)".
Disconnect the G115 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
NG
OK
Disconnect the G75 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
NG
OK
Disconnect the G73 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the G74 No. 2 CAN junction connector LH.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G15-14 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the G19 center airbag sensor assembly connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G132-1 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G132-2 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the G18 steering angle sensor connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G72-1 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G72-2 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the G91 power steering ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G130-1 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G130-2 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the G59 main body ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G75-1 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G75-2 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the F17 navigation receiver assembly connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G115-1 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| G115-2 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N48-2 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| N48-7 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N48-3 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| N48-8 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the N21 yaw rate sensor connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N48-2 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| N48-7 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG
Disconnect the G28 combination meter assembly (combination meter ECU) connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N48-3 (CANH) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
| N48-8 (CANL) - G15-4 (CG) | Engine switch off | 200 Ω or higher |
OK
NG