There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. | ·
Short between CAN bus lines ·
Brake actuator assembly (skid control ECU)*1 ·
ABS and traction actuator (skid control ECU)*2 ·
Power steering ECU ·
Steering angle sensor*3 ·
Yaw rate sensor*2 ·
ECM ·
Center airbag sensor assembly ·
Air conditioning amplifier ·
Combination meter assembly (Combination meter ECU) ·
Instrument panel junction block (Main body ECU) ·
Network gateway ECU ·
No. 2 CAN junction connector LH ·
No. 2 junction connector ·
No. 4 junction connector ·
No. 5 junction connector |
*1: w/o VSC
*2: w/ VSC
*3: w/ VSC or w/ AFS
Turn the engine switch off before measuring the resistances of the main wire and the branch wire.
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Disconnect the G104 No. 4 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Reconnect the G104 No. 4 junction connector.
Disconnect the G73 No. 2 CAN junction connector LH connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Reconnect the G73 No. 2 CAN junction connector LH connector.
Disconnect the G84 No. 2 CAN junction connector LH connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the A35 ABS and traction actuator (skid control ECU) connector or A22 brake actuator assembly (skid control ECU) connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G84-1 (CANH) - G84-2 (CANL) | Engine switch off | 1 MΩ or higher |
| OK (w/ VSC) | A |
|---|---|
| OK (w/o VSC) | B |
| NG | C |
A
B
C
Disconnect the G74 No. 2 CAN junction connector LH connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Disconnect the A7 ECM connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G74-1 (CANH) - G74-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the G77 No. 2 CAN junction connector LH connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the G47 air conditioning amplifier connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-1 (CANH) - G77-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the G75 No. 2 CAN junction connector LH connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the G59 main body ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G75-1 (CANH) - G75-2 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the G103 No. 5 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G103-11 (CANH) - G103-22 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Reconnect the G73 No. 2 CAN junction connector LH connector.
Reconnect the G103 No. 5 junction connector.
Disconnect the G91 power steering ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G91-1 (CANH) - G91-7 (CANL) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the G103 No. 5 junction connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G103-10 (CANH) - G103-21 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Reconnect the G103 No. 5 junction connector.
Disconnect the G19 center airbag sensor assembly connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-13 (CANH) - G19-22 (CANL) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the G103 No. 5 junction connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G103-8 (CANH) - G103-19 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the N35 No. 2 junction connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G103-7 (CANH) - G103-18 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Reconnect the G73 No. 2 CAN junction connector LH connector.
Reconnect the G103 No. 5 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G15-6 (CANH) - G15-14 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Reconnect the N35 No. 2 junction connector.
Disconnect the N21 yaw rate sensor connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N21-2 (CANH) - N21-3 (CANL) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the N35 No. 2 junction connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N35-2 (CANH) - N35-7 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Disconnect the G104 No. 4 junction connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N35-1 (CANH) - N35-6 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Reconnect the N35 No. 2 junction connector.
Reconnect the G104 No. 4 junction connector.
Disconnect the G18 steering angle sensor connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G18-10 (CANH) - G18-9 (CANL) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the G104 No. 4 junction connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G104-9 (CANH) - G104-20 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Reconnect the G104 No. 4 junction connector.
Disconnect the G40 network gateway ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-16 (CA1H) - G40-15 (CA1L) | Engine switch off | 54 to 69 Ω |
OK
NG
Disconnect the G104 No. 4 junction connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G104-11 (CANH) - G104-22 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G104-8 (CANH) - G104-19 (CANL) | Engine switch off | 104 to 132 Ω |
OK
NG
Disconnect the G28 combination meter assembly (combination meter ECU) connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G104-8 (CANH) - G104-19 (CANL) | Engine switch off | 1 MΩ or higher |
OK
NG