Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
MAIN BODY ECU COMMUNICATION STOP MODE When either condition below is met:
·

Main Body is not displayed on "BUS CHECK" screen of intelligent tester

·

Applies to "MAIN BODY ECU COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE"


·

Power source or inside main body ECU

·

Main body ECU branch wire and connector

·

Main body ECU



WIRING DIAGRAM

C267881E05
0.469,1.969 2.677,2.354 2.208,0.385 10 false No. 2 CAN Junction Connector LH 0.146,1.969 0.583,2.146 0.438,0.177 10 false G75 0.469,3.5 2.625,3.906 2.156,0.406 10 false No. 3 CAN Junction Connector 0.104,3.49 0.458,3.677 0.354,0.188 10 false M48 5.74,6.021 6.771,6.188 1.031,0.167 10 false Main Body ECU 5.854,1.094 6.292,1.26 0.438,0.167 10 false CANH 5.854,1.542 6.26,1.688 0.406,0.146 10 false CANL 5.854,2.604 6.292,2.771 0.438,0.167 10 false CANP 5.854,3.052 6.281,3.198 0.427,0.146 10 false CANN 5.854,3.74 6.292,3.906 0.438,0.167 10 false BECU 5.854,4.406 6.521,4.698 0.667,0.292 10 false GND1 5.854,5.323 6.26,5.469 0.406,0.146 10 false GND2 4.385,3.552 4.885,3.698 0.5,0.146 10 false ECU-B 2.51,5.719 3.333,5.917 0.823,0.198 10 false from Battery 1.563,1.01 1.677,1.177 0.115,0.167 10 false 1 1.563,1.438 1.677,1.604 0.115,0.167 10 false 2 1.563,2.531 1.677,2.698 0.115,0.167 10 false 1 1.573,2.958 1.688,3.125 0.115,0.167 10 false 9 5.583,0.927 5.708,1.073 0.125,0.146 10 false 5 5.573,1.375 5.698,1.521 0.125,0.146 10 false 6 5.521,2.458 5.729,2.604 0.208,0.146 10 false 16 5.531,2.885 5.74,3.031 0.208,0.146 10 false 15 5.583,3.646 5.792,3.792 0.208,0.146 10 false 26 5.365,3.563 5.469,3.708 0.104,0.146 10 false 1 5.583,4.24 5.688,4.385 0.104,0.146 10 false 1 5.625,5.24 5.74,5.396 0.115,0.156 10 false 4 5.375,5.177 5.552,5.333 0.177,0.156 10 false 3 5.323,5.344 5.521,5.49 0.198,0.146 10 false 4A 5.479,4.417 5.76,4.573 0.281,0.156 10 false G59 5.479,1.115 5.76,1.271 0.281,0.156 10 false G59 5.49,1.552 5.771,1.708 0.281,0.156 10 false G59 5.479,2.635 5.76,2.792 0.281,0.156 10 false G59 5.479,3.063 5.76,3.219 0.281,0.156 10 false G59 5.323,3.75 5.521,3.896 0.198,0.146 10 false 4P

CAUTION / NOTICE / HINT

NOTICE:

Turn the engine switch off before measuring the resistances of the main wire and the branch wire.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK CAN BUS LINE FOR DISCONNECTION (MAIN BODY ECU)
a.
U189296E02
1.396,2.198 1.052,2.021 false 1.51,2.24 1.104,2.708 false 1.917,2.385 2.125,2.75 false 2.031,2.375 2.448,2.51 false 0.146,0.094 1.5,0.26 1.354,0.167 10 false Wire Harness Side: 1.563,1.063 1.854,1.208 0.292,0.146 10 false G59 0.615,1.906 1.042,2.063 0.427,0.156 10 false CANH 0.74,2.698 1.167,2.854 0.427,0.156 10 false CANL 2.531,2.458 2.958,2.615 0.427,0.156 10 false CANP 2.042,2.792 2.469,2.948 0.427,0.156 10 false CANN

Disconnect the G59 main body ECU connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
G59-5 (CANH) - G59-6 (CANL) Engine switch off 54 to 69 Ω
G59-16 (CANP) - G59-15 (CANN) Engine switch off 108 to 132Ω




OK

2.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL and CANP, CANN)

2.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY AND BODY GROUND)
C367898E03
1.719,0.427 2.115,0.625 0.396,0.198 4.656,0.427 5.052,0.625 0.396,0.198 1.667,2.188 2.063,2.385 0.396,0.198 1.229,1.625 1.646,1.271 false 0.896,2.292 1.365,2.729 false 4.177,1.594 4.542,1.365 false 0.219,0.083 2.969,0.281 2.75,0.198 10 false Wire Harness Side: 1.792,0.448 2.146,0.688 0.354,0.24 10 false G59 4.76,0.448 5.115,0.688 0.354,0.24 10 false 4P 1.792,2.208 2.146,2.448 0.354,0.24 10 false 4A 0.823,1.573 1.208,1.813 0.385,0.24 10 false GND1 0.479,2.188 0.927,2.448 0.448,0.26 10 false GND2 3.76,1.542 4.146,1.781 0.385,0.24 10 false BECU

a.

Disconnect the 4A and 4P junction block connectors.


b.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G59-1 (GND1) - Body ground Below 1 Ω
4A-3 (GND2) - Body ground Below 1 Ω



c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
4P-1 (BECU) - Body ground 10 to 14 V




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR