Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2013.04–2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Navigation ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Navigation ECU Communication Stop Mode
·

"AVN" is not displayed on the "Communication Bus Check" screen of the intelligent tester

·

Applies to "Navigation ECU Communication Stop Mode" in the "DTC COMBINATION TABLE"


·

Power source circuit of the navigation receiver assembly

·

Navigation receiver assembly branch wire or connector

·

Navigation receiver assembly



WIRING DIAGRAM

C141066E08
0.167,2.74 2.302,3.063 2.135,0.323 10 false No. 2 CAN Junction Connector LH 1.542,1.469 1.677,1.615 0.135,0.146 10 false 1 1.542,1.927 1.677,2.073 0.135,0.146 10 false 2 1.698,5.063 2.49,5.281 0.792,0.219 10 false from Battery 2.771,5.073 4.125,5.26 1.354,0.188 10 false from RH-IG Relay 1 4.281,3.104 5.021,3.271 0.74,0.167 10 false RAD NO. 1 4.25,3.896 5.063,4.063 0.813,0.167 10 false RH ECU-IG 5.594,5.917 6.885,6.563 1.292,0.646 10 false Navigation Receiver Assembly 5.802,1.583 6.219,1.75 0.417,0.167 10 false CANH 5.802,2.021 6.219,2.188 0.417,0.167 10 false CANL 5.802,3.271 6,3.438 0.198,0.167 10 false +B 5.802,4.063 5.979,4.229 0.177,0.167 10 false IG 5.813,4.615 6.229,4.781 0.417,0.167 10 false GND 5.552,1.396 5.656,1.552 0.104,0.156 10 false 9 5.51,1.833 5.708,1.99 0.198,0.156 10 false 10 5.542,3.042 5.646,3.198 0.104,0.156 10 false 4 5.552,3.875 5.656,4.031 0.104,0.156 10 false 1 5.552,4.438 5.656,4.594 0.104,0.156 10 false 7 5.458,4.625 5.76,4.802 0.302,0.177 10 false F13 5.458,4.073 5.74,4.24 0.281,0.167 10 false F17 5.469,3.26 5.75,3.438 0.281,0.177 10 false F13 5.469,1.583 5.74,1.75 0.271,0.167 10 false F17 5.469,2.021 5.74,2.188 0.271,0.167 10 false F17 0.167,2.563 0.906,2.729 0.74,0.167 10 false G96

CAUTION / NOTICE / HINT

NOTICE:

Turn the engine switch off before measuring the resistances of the main wire and the branch wires.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U189574E02
0.927,1.292 1.167,1.292 1.167,1.292 1.792,1.906 false 2.729,1.479 2.51,1.479 2.51,1.479 1.917,1.896 false 0.156,0.125 2.51,0.771 2.354,0.646 10 false Front view of wire harness connector (to Navigation Receiver Assembly) 2.771,1.396 3.219,1.594 0.448,0.198 10 false CANL 0.469,1.208 0.917,1.406 0.448,0.198 10 false CANH 1.5,2.573 1.802,2.729 0.302,0.156 10 false F17

Disconnect the F17 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-9 (CANH) - F17-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the F13 navigation receiver assembly connector.


b.
U189577E02
1.49,3.802 1.49,4.135 1.49,4.135 1.344,4.135 false 0.823,1.656 0.823,1.167 0.823,1.167 0.667,1.167 false 2.031,3.563 2.365,3.563 false 0.5,0.083 2.823,0.906 2.323,0.823 10 true Front view of wire harness connector (to Navigation Receiver Assembly) 0.458,1.083 0.688,1.271 0.229,0.188 10 false IG 0.969,4.042 1.323,4.219 0.354,0.177 10 false GND 0.24,1.531 0.542,1.708 0.302,0.177 10 false F17 0.313,3.604 0.615,3.781 0.302,0.177 10 false F13 2.427,3.479 2.729,3.656 0.302,0.177 10 false +B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-7 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Connect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F13-4 (+B) - Body ground Always 11 to 14 V
F17-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)