Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2013.04–2016.05
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Brake Actuator (Skid Control ECU) Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
BRAKE ACTUATOR (SKID CONTROL ECU) COMMUNICATION STOP MODE When either condition below is met:
·

ABS/VSC/TRC is not displayed on "BUS CHECK" screen of intelligent tester

·

Applies to "BRAKE ACTUATOR (SKID CONTROL ECU) COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE"


·

Power source or inside brake actuator (skid control ECU)

·

Brake actuator assembly (skid control ECU) branch wire and connector

·

Brake actuator assembly (skid control ECU)



HINT:

For vehicles without VSC only.


WIRING DIAGRAM

C132261E11
0.177,2.813 2.01,3.167 1.833,0.354 10 false No. 1 Junction Connector*1 5.604,5.771 6.844,6.354 1.24,0.583 10 false Brake Actuator (Skid Control ECU) 5.865,1.646 6.344,1.813 0.479,0.167 10 false CANH 5.865,2.094 6.344,2.26 0.479,0.167 10 false CANL 5.865,3.177 6.198,3.365 0.333,0.188 10 false IG1 5.865,4.021 6.354,4.208 0.49,0.188 10 false GND1 5.865,4.76 6.354,4.948 0.49,0.188 10 false GND2 4.135,3.021 5.083,3.219 0.948,0.198 10 false GAUGE NO. 1 2.75,4.125 4.031,4.323 1.281,0.198 10 false from LH-IG Relay 2 0.177,3.292 2.542,3.646 2.365,0.354 10 false No. 2 CAN Junction Connector LH*2 5.49,1.552 5.719,1.729 0.229,0.177 10 false 26 5.5,1.99 5.74,2.177 0.24,0.188 10 false 15 5.479,3.063 5.719,3.271 0.24,0.208 10 false 18 5.573,3.906 5.729,4.042 0.156,0.135 10 false 4 5.573,4.635 5.729,4.771 0.156,0.135 10 false 1 0.385,5.792 1.198,5.99 0.813,0.198 10 false *1: for LHD 0.385,6.135 1.198,6.333 0.813,0.198 10 false *2: for RHD 1.521,1.521 1.635,1.708 0.115,0.188 10 false 1 1.542,1.99 1.927,2.177 0.385,0.188 10 false 5*1 1.542,2.229 1.927,2.417 0.385,0.188 10 false 2*2 5.615,5.604 6.104,5.792 0.49,0.188 10 false A22 0.167,3.135 0.656,3.323 0.49,0.188 10 false G84 0.177,2.656 0.667,2.844 0.49,0.188 10 false A29

CAUTION / NOTICE / HINT

NOTICE:

Turn the ignition switch OFF before measuring the resistances of the main wire and the branch wire.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK CAN BUS LINE FOR DISCONNECTION (BRAKE ACTUATOR ASSEMBLY BRANCH WIRE)
a.
U189183E02
2.521,1.646 2.833,1.052 false 2.573,1.781 2.875,2.521 false 1.604,0.75 1.885,0.896 0.281,0.146 10 false A22 2.792,2.531 3.229,2.677 0.438,0.146 10 false CANH 2.802,0.906 3.24,1.052 0.438,0.146 10 false CANL

Disconnect the A22 brake actuator (skid control ECU) connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
A22-26 (CANH) - A22-15 (CANL) Ignition switch off 54 to 69 Ω




OK

2.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR ASSEMBLY (CANH, CANL)

2.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U189184E01
1.68,0.767 1.954,0.930 0.274,0.163 10 A22 0.889,2.46 1.309,2.606 0.420,0.147 10 GND1 0.099,0.838 0.519,0.985 0.420,0.147 10 GND2 1.95,2.468 2.198,2.615 0.248,0.147 10 IG1 0.992,1.678 0.614,0.916 false 1.376,1.739 1.101,2.46 false 1.845,1.748 2.05,2.432 false

Disconnect the A22 brake actuator (skid control ECU) connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A22-4 (GND1) - Body ground Below 1 Ω
A22-1 (GND2) - Body ground Below 1 Ω



c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
A22-18 (IG1) - Body ground Ignition switch on (IG) 10 to 14 V




OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR