Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2014.09
RM24M0E _57 Power Source / Network _059598 CAN COMMUNICATION _0292257 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) COMMUNICATION STOP MODE When either condition below is met:
·

ABS/VSC/TRC is not displayed on "BUS CHECK" screen of intelligent tester

·

Applies to "ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE"


·

Power source or inside ABS and traction actuator (skid control ECU)

·

ABS and traction actuator (skid control ECU) branch wire and connector

·

ABS and traction actuator (skid control ECU)



HINT:

For vehicle with VSC only.


WIRING DIAGRAM

U189029E02
0.135,3.115 1.896,3.438 1.76,0.323 10 false No. 1 Junction Connector*1 5.344,5.896 7.073,6.469 1.729,0.573 10 false ABS and Traction Actuator (Skid Control ECU) 5.854,2.01 6.375,2.167 0.521,0.156 10 false CANH 5.854,2.438 6.375,2.594 0.521,0.156 10 false CANL 5.854,3.438 6.24,3.604 0.385,0.167 10 false IG1 5.865,4.302 6.292,4.49 0.427,0.188 10 false GND1 5.844,4.979 6.271,5.167 0.427,0.188 10 false GND2 4.177,3.281 5.271,3.448 1.094,0.167 10 false GAUGE NO. 1 2.729,4.427 4.135,4.635 1.406,0.208 10 false from LH-IG Relay 2 0.125,3.708 2.698,4.031 2.573,0.323 10 false No. 2 CAN Junction Connector LH*2 5.552,1.917 5.771,2.073 0.219,0.156 10 false 26 5.552,2.344 5.771,2.5 0.219,0.156 10 false 14 5.552,3.323 5.771,3.479 0.219,0.156 10 false 28 5.542,4.219 5.833,4.375 0.292,0.156 10 false 38 5.552,4.906 5.781,5.063 0.229,0.156 10 false 13 1.552,2.354 1.844,2.51 0.292,0.156 10 false 5*1 1.552,1.906 1.771,2.063 0.219,0.156 10 false 1 0.208,6.135 0.99,6.281 0.781,0.146 10 false *1: for LHD 0.208,6.469 0.99,6.615 0.781,0.146 10 false *2: for RHD 1.552,2.563 1.844,2.719 0.292,0.156 10 false 2*2 5.365,5.729 5.792,5.917 0.427,0.188 10 false A35 0.146,2.969 0.438,3.125 0.292,0.156 10 false A29 0.125,3.542 0.417,3.698 0.292,0.156 10 false G84

CAUTION / NOTICE / HINT

NOTICE:

Turn the engine switch off before measuring the resistances of the main wire and the branch wire.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK CAN BUS LINE FOR DISCONNECTION (ABS AND TRACTION ACTUATOR BRANCH WIRE)
a.
U189690E02
0.552,1.917 0.927,1.042 false 1.042,1.24 1.698,1.979 false 1.927,0.302 2.24,0.458 0.313,0.156 10 false A35 0.135,1.875 0.563,2.042 0.427,0.167 10 false CANH 1.719,1.917 2.125,2.083 0.406,0.167 10 false CANL 0.083,0.052 1.573,0.25 1.49,0.198 10 false Wire Harness Side:

Disconnect the A35 ABS and traction actuator (skid control ECU) connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
A35-26 (CANH) - A35-14 (CANL) Engine switch off 54 to 69 Ω




OK

2.CHECK WIRE HARNESS (ABS AND TRACTION ACTUATOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ABS AND TRACTION ACTUATOR (CANH, CANL)

2.CHECK WIRE HARNESS (ABS AND TRACTION ACTUATOR - BATTERY AND BODY GROUND)
a.
U189691E02
1.208,0.969 2.083,0.354 false 2.677,1.344 2.021,1.875 false 2.771,1.073 3.167,1.792 false 2.99,0.313 3.302,0.469 0.313,0.156 10 false A35 2.115,0.24 2.542,0.406 0.427,0.167 10 false IG1 1.781,1.885 2.281,2.052 0.5,0.167 10 false GND2 0.083,0.052 1.573,0.25 1.49,0.198 10 false Wire Harness Side: 2.948,1.802 3.375,1.969 0.427,0.167 10 false GND1

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A35-13 (GND2) - Body ground Below 1 Ω
A35-38 (GND1) - Body ground Below 1 Ω



b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
A35-28 (IG1) - Body ground Engine switch on (IG) 10 to 14 V




OK

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR