| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| B2326 | CAN MS Bus Line Communication Malfunction | ·
CAN MS bus circuit ·
Certification ECU branch wire and connector ·
Power slide door ECU RH branch wire and connector ·
Power slide door ECU LH branch wire and connector ·
Power back door ECU branch wire and connector ·
Main body ECU main wire and connector ·
Combination meter ECU main wire and connector ·
Main body ECU ·
Combination meter ECU ·
No. 2 junction connector ·
No. 3 junction connector ·
No. 2 CAN junction connector RH ·
Power slide door ECU RH*1 ·
Power slide door ECU LH*1 ·
Power back door ECU*2 ·
Certification ECU |
*1: w/ Power Slide Door System
*2: w/ Power Back Door System
Remove the main body ECU with the connector connected.
Disconnect the 4P ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition | Resistance of Malfunction |
|---|---|---|
| G59-16 (CANP) - G59-15 (CANN) | 54 to 69 Ω | Below 53 Ω: Short in line |
| 70 Ω or more: Open in CAN main bus line | ||
| G59-16 (CANP) - 4P-1 (BECU) | 6 kΩ or more | Below 6 kΩ: +B short |
| G59-15 (CANN) - 4P-1 (BECU) | 6 kΩ or more | Below 6 kΩ: +B short |
| G59-16 (CANP) - G59-1 (GND1) | 200 Ω or more | Below 200 Ω: Ground short |
| G59-15 (CANN) - G59-1 (GND1) | 200 Ω or more | Below 200 Ω: Ground short |
| Result | Proceed to |
|---|---|
| NG
- Open in CAN main bus line |
A |
| NG
- Short in line - +B short - Ground short |
B |
| OK | C |
A
B
C
Disconnect the G81 No. 2 CAN junction connector RH.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G81-1 (CANH) - G81-2 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Reconnect the G81 No. 2 CAN junction connector RH.
NEXT
Disconnect the G129 No. 2 CAN junction connector RH.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G129-1 (CANH) - G129-2 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Reconnect the G81 No. 2 CAN junction connector RH.
NEXT
Disconnect the M48 No. 3 junction connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M48-1 (CANH) - M48-9 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M48-2 (CANH) - M48-10 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Reconnect the M48 No. 3 junction connector.
NEXT
Disconnect the G59 main body ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G59-16 (CANP) - G59-15 (CANN) | Engine switch off | 108 to 132 Ω |
OK
NG
Reconnect the G129 No. 2 CAN junction connector RH.
NEXT
Disconnect the N48 No. 2 junction connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N48-5 (CANH) - N48-10 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N48-4 (CANH) - N48-9 (CANL) | Engine switch off | 108 to 132 Ω |
OK
NG
Reconnect the N48 No. 2 junction connector.
NEXT
Disconnect the G28 combination meter ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G28-18 (MPX+) - G28-19 (MPX-) | Engine switch off | 108 to 132 Ω |
OK
NG
Remove the instrument panel junction block LH with the connector.
Disconnect the G81 No. 2 CAN junction connector RH.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| G59-16 (CANP) - G59-15 (CANN) | 108 to 132 Ω |
| G59-16 (CANP) - G15-4 (CG) | 200 Ω or more |
| G59-15 (CANN) - G15-4 (CG) | 200 Ω or more |
| G59-16 (CANP) - G15-16 (BAT) | 6 kΩ or more |
| G59-15 (CANN) - G15-16 (BAT) | 6 kΩ or more |
NG
OK
Reconnect the G81 No. 2 CAN junction connector RH.
NEXT
Disconnect the M48 No. 3 junction connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| M48-2 (CANH) - M48-10 (CANL) | 108 to 132 Ω |
| M48-2 (CANH) - G15-4 (CG) | 200 Ω or more |
| M48-10 (CANL) - G15-4 (CG) | 200 Ω or more |
| M48-2 (CANH) - G15-16 (BAT) | 6 kΩ or more |
| M48-10 (CANL) - G15-16 (BAT) | 6 kΩ or more |
OK
NG
For vehicles without power slide door system, go to "CAN BUS LINES FOR SHORT (NO. 3 JUNCTION CONNECTOR - POWER BACK DOOR ECU)"
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| M48-3 (CANH) - M48-11 (CANL) | Engine switch off | 1 Ω or more | OK |
| M48-3 (CANH) - M48-11 (CANL) | Engine switch off | Below 1 Ω | NG |
| M48-3 (CANH) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M48-11 (CANL) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M48-3 (CANH) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M48-11 (CANL) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M48-3 (CANH) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M48-11 (CANL) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M48-3 (CANH) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| M48-11 (CANL) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
For vehicle w/ Power Back Door System:
Perform the procedures below.
For vehicle w/o Power Back Door System:
Go to "CHECK CAN BUS LINES FOR SHORT (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)"
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| M48-8 (CANH) - M48-4 (CANL) | Engine switch off | 1 Ω or more | OK |
| M48-8 (CANH) - M48-4 (CANL) | Engine switch off | Below 1 Ω | NG |
| M48-8 (CANH) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M48-4 (CANL) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M48-8 (CANH) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M48-4 (CANL) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M48-8 (CANH) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M48-4 (CANL) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M48-8 (CANH) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| M48-4 (CANL) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| M48-1 (CANH) - M48-9 (CANL) | Engine switch off | 1 Ω or more | OK |
| M48-1 (CANH) - M48-9 (CANL) | Engine switch off | Below 1 Ω | NG |
| M48-1 (CANH) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M48-9 (CANL) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M48-1 (CANH) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M48-9 (CANL) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M48-1 (CANH) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M48-9 (CANL) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M48-1 (CANH) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| M48-9 (CANL) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
Reconnect the M48 No. 3 junction connector.
NEXT
Disconnect the M22 power slide door ECU LH connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| M22-11 (MPX1) - M22-5 (MPX2) | Engine switch off | 1 Ω or more | OK |
| M22-11 (MPX1) - M22-5 (MPX2) | Engine switch off | Below 1 Ω | NG |
| M22-11 (MPX1) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M22-5 (MPX2) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M22-11 (MPX1) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M22-5 (MPX2) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M22-11 (MPX1) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M22-5 (MPX2) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M22-11 (MPX1) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| M22-5 (MPX2) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
Reconnect the M48 No. 3 junction connector.
NEXT
Disconnect the M24 power back door ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| M24-6 (MPX1) - M24-5 (MPX2) | Engine switch off | 1 Ω or more | OK |
| M24-6 (MPX1) - M24-5 (MPX2) | Engine switch off | Below 1 Ω | NG |
| M24-6 (MPX1) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M24-5 (MPX2) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| M24-6 (MPX1) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M24-5 (MPX2) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| M24-6 (MPX1) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M24-5 (MPX2) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| M24-6 (MPX1) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| M24-5 (MPX2) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
Reconnect the M48 No. 3 junction connector.
NEXT
Disconnect the G59 main body ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| G59-16 (CANP) - G59-15 (CANN) | Engine switch off | 1 Ω or more | OK |
| G59-16 (CANP) - G59-15 (CANN) | Engine switch off | Below 1 Ω | NG |
| G59-16 (CANP) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| G59-15 (CANN) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| G59-16 (CANP) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| G59-15 (CANN) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| G59-16 (CANP) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| G59-15 (CANN) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| G59-16 (CANP) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| G59-15 (CANN) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
Reconnect the G81 No. 2 CAN junction connector RH.
NEXT
Disconnect the G129 No. 2 CAN junction connector RH.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| G28-18 (MPX+) - G28-19 (MPX-) | 108 to 132 Ω |
| G28-18 (MPX+) - G15-4 (CG) | 200 Ω or more |
| G28-19 (MPX-) - G15-4 (CG) | 200 Ω or more |
| G28-18 (MPX+) - G15-16 (BAT) | 6 kΩ or more |
| G28-19 (MPX-) - G15-16 (BAT) | 6 kΩ or more |
NG
OK
Disconnect the N48 No. 2 junction connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| N48-5 (CANH) - N48-10 (CANL) | 108 to 132 Ω |
| N48-5 (CANH) - G15-4 (CG) | 200 Ω or more |
| N48-10 (CANL) - G15-4 (CG) | 200 Ω or more |
| N48-5 (CANH) - G15-16 (BAT) | 6 kΩ or more |
| N48-10 (CANL) - G15-16 (BAT) | 6 kΩ or more |
OK
NG
Reconnect the G129 No. 2 CAN junction connector RH.
NEXT
For vehicles without power slide door system, go to "CHECK CAN BUS LINES FOR SHORT (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ECU)"
Disconnect the N48 No. 2 junction connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| N48-12 (CANH) - N48-11 (CANL) | Engine switch off | 1 Ω or more | OK |
| N48-12 (CANH) - N48-11 (CANL) | Engine switch off | Below 1 Ω | NG |
| N48-12 (CANH) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| N48-11 (CANL) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| N48-12 (CANH) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| N48-11 (CANL) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| N48-12 (CANH) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| N48-11 (CANL) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| N48-12 (CANH) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| N48-11 (CANL) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| N48-4 (CANH) - N48-9 (CANL) | Engine switch off | 1 Ω or more | OK |
| N48-4 (CANH) - N48-9 (CANL) | Engine switch off | Below 1 Ω | NG |
| N48-4 (CANH) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| N48-9 (CANL) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| N48-4 (CANH) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| N48-9 (CANL) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| N48-4 (CANH) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| N48-9 (CANL) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| N48-4 (CANH) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| N48-9 (CANL) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
NG
OK
Reconnect the N48 No. 2 junction connector.
NEXT
Disconnect the N24 power slide door ECU RH connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| N24-8 (MPX1) - N24-2 (MPX2) | Engine switch off | 1 Ω or more | OK |
| N24-8 (MPX1) - N24-2 (MPX2) | Engine switch off | Below 1 Ω | NG |
| N24-8 (MPX1) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| N24-2 (MPX2) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| N24-8 (MPX1) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| N24-2 (MPX2) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| N24-8 (MPX1) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| N24-2 (MPX2) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| N24-8 (MPX1) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| N24-2 (MPX2) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
Reconnect the N48 No. 2 junction connector.
NEXT
Disconnect the G28 combination meter ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| G28-18 (MPX+) - G28-19 (MPX-) | Engine switch off | 1 Ω or more | OK |
| G28-18 (MPX+) - G28-19 (MPX-) | Engine switch off | Below 1 Ω | NG |
| G28-18 (MPX+) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| G28-19 (MPX-) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| G28-18 (MPX+) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| G28-19 (MPX-) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| G28-18 (MPX+) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| G28-19 (MPX-) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| G28-18 (MPX+) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| G28-19 (MPX-) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
Reconnect the G129 No. 2 CAN junction connector RH.
NEXT
Disconnect the G80 No. 2 CAN junction connector RH.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| G80-1 (CANH) - G80-2 (CANL) | Engine switch off | 1 Ω or more | OK |
| G80-1 (CANH) - G80-2 (CANL) | Engine switch off | Below 1 Ω | NG |
| G80-1 (CANH) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| G80-2 (CANL) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| G80-1 (CANH) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| G80-2 (CANL) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| G80-1 (CANH) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| G80-2 (CANL) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| G80-1 (CANH) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| G80-2 (CANL) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
NG
OK
Reconnect the G80 No. 2 CAN junction connector RH.
NEXT
Disconnect the G29 certification ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Measured Resistance | Proceed to |
|---|---|---|---|
| G29-27 (CANH) - G29-28 (CANL) | Engine switch off | 1 Ω or more | OK |
| G29-27 (CANH) - G29-28 (CANL) | Engine switch off | Below 1 Ω | NG |
| G29-27 (CANH) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| G29-28 (CANL) - G15-4 (CG) | Engine switch off | 1 Ω or more | OK |
| G29-27 (CANH) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| G29-28 (CANL) - G15-4 (CG) | Engine switch off | Below 1 Ω | NG |
| G29-27 (CANH) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| G29-28 (CANL) - G15-16 (BAT) | Engine switch off | 1 Ω or more | OK |
| G29-27 (CANH) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
| G29-28 (CANL) - G15-16 (BAT) | Engine switch off | Below 1 Ω | NG |
OK
NG
Recheck for DTC.
NEXT