REASSEMBLY
Removal / installation · Vehicles built from Nov 2010
Versions by build date: Jul 2007 – Oct 2010 from Nov 2010
| 1.
INSTALL NO. 1 COOLER THERMISTOR (for LHD) |
 |
- Install the sensor onto the evaporator as shown in the illustration.
- Standard:
Part
|
Length
|
A
|
50 mm (1.97 in.)
|
B
|
100.5 mm (3.96 in.)
|
C
|
74.5 mm (2.93 in.)
|
D
|
255.4 mm (10.06 in.)
|
Text in Illustration
*a
|
Sensor
|
*b
|
Evaporator
|
Check that the sensor sticks to the evaporator surface as shown in the illustration.
- NOTICE:
- If reusing the evaporator, do not reinsert the sensor in the same position that it was in before. Insert it within area X shown in the illustration.
| 2.
INSTALL NO. 1 COOLER THERMISTOR (for RHD) |
 |
- Install the sensor onto the evaporator as shown in the illustration.
- Standard:
Part
|
Length
|
A
|
50 mm (1.97 in.)
|
B
|
30 mm (1.18 in.)
|
C
|
34.3 mm (1.35 in.)
|
D
|
47.7 mm (1.88 in.)
|
E
|
114.7 mm (4.52 in.)
|
Text in Illustration
*a
|
Sensor
|
*b
|
Evaporator
|
Check that the sensor sticks to the evaporator surface as shown in the illustration.
- NOTICE:
- If reusing the evaporator, do not reinsert the sensor in the same position that it was in before. Insert it within area X shown in the illustration.
| 3.
INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY |
 |
Apply sufficient compressor oil (ND-OIL8) to 2 new O-rings and the fitting surface of the cooler evaporator.
- Compressor oil:
- ND-OIL8 or the equivalent
Install the cover plate.
Install the 2 O-rings onto the cooler evaporator.
Install the cooler evaporator.
- HINT:
- If a new cooler evaporator is installed, add compressor oil to the cooler evaporator as follows.
- Compressor oil:
- ND-OIL8 or the equivalent. Add 40 cc (1.35 fl. oz.)
Install the cooler evaporator onto the heater case.
- Install the heater case with the 8 screws.
- Install the plate with the 2 screws.
| 4.
INSTALL COOLER EXPANSION VALVE |
 |
Apply sufficient compressor oil (ND-OIL8) to the fitting surface of the cooler expansion valve.
- Compressor oil:
- ND-OIL8 or the equivalent
Install the cooler expansion valve onto the cooler evaporator.
| 5.
INSTALL AIR CONDITIONING TUBE ASSEMBLY |
 |
Apply sufficient compressor oil (ND-OIL8) to 2 new O-rings and the fitting surface of the air conditioning tube.
- Compressor oil:
- ND-OIL8 or the equivalent
Install the 2 O-rings onto the air conditioning tube.
Using a hexagon wrench 4, install the air conditioning tube with the 2 hexagon bolts.
-
Torque:
- 3.5 N*m{
36 kgf*cm
, 31 in.*lbf
}
| 6.
INSTALL COVER PLATE |
 |
- Engage the claw.
Install the cover plate with the screw.
| 7.
INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (for LHD) |
 |
- Install the heater radiator unit onto the heater case.
Install the clamp with the screw.
| 8.
INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (for RHD) |
 |
- Install the heater radiator unit onto the heater case.
Engage the guide and tighten the 2 screws.
| 9.
INSTALL COOLER UNIT DRAIN HOSE |
 |
- Install the cooler unit drain hose.
| 10.
INSTALL AIR MIX CONTROL SERVO MOTOR |
 |
- Install the air mix control servo motor with the 3 screws.
| 11.
INSTALL MODE CONTROL SERVO MOTOR |
 |
- Install the mode control servo motor with the 3 screws.