2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010


1. REMOVE FRONT DOOR SCUFF PLATE LH

  1. E129562
    Disengage the 14 claws and remove the front door scuff plate.


2. REMOVE FRONT FLOOR FOOTREST (for LHD)

  1. B130586
    Disengage the 4 claws and remove the front floor footrest.


3. REMOVE FOOTREST CLIP (for LHD)

  1. B130587
    Remove the 2 footrest clips.


4. REMOVE COWL SIDE TRIM BOARD LH

  1. E129563
    Remove the clip.

  1. Disengage the 2 claws and remove the cowl side trim board.


5. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip LH.


6. REMOVE INSTRUMENT PANEL GARNISH LH (for LHD)

  1. B133886
    Remove screw <G>.

  1. Disengage the 3 clips and remove the instrument panel garnish.

    NOTICE:
    1. Pull the instrument panel garnish up at an angle of 45° to remove it.
    2. Do not damage the surface of the instrument panel when removing it.


7. REMOVE INSTRUMENT PANEL GARNISH RH (for RHD)

  1. B133887
    Remove screw <G>.

  1. Disengage the 3 clips and remove the instrument panel garnish.

    NOTICE:
    1. Pull the instrument panel garnish up at an angle of 45° to remove it.
    2. Do not damage the surface of the instrument panel when removing it.


8. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B133888
    Remove the 2 screws.

  1. Disengage the 4 clips and remove the integration control panel assembly.

  1. Disconnect the 3 connectors.


9. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B133859
    Disengage the 3 claws and separate the hood lock control lever.


10. SEPARATE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD)

  1. B267057
    Disengage the 3 claws and separate the fuel lid lock open lever.


11. REMOVE INSTRUMENT PANEL FINISH PLATE

  1. E149562E03
    Using a screwdriver with its tip wrapped in protective tape, remove the instrument panel finish plate.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Instrument Panel Finish Plate


12. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)

  1. B133860
    Remove the 2 <E> bolts.

  1. Disengage the 5 clips and claw and remove the lower instrument panel finish panel.


13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)

  1. B267058
    Remove the 2 <E> bolts.

  1. Disengage the 8 clips and 4 guides.

  1. Disconnect the connectors and remove the lower instrument panel finish panel.


14. REMOVE INSTRUMENT CLUSTER FINISH PANEL (for LHD)

  1. B133861
    Disengage the 3 clips and the 4 claws and remove the instrument cluster finish panel.

  1. Disconnect the connectors.


15. REMOVE INSTRUMENT CLUSTER FINISH PANEL (for RHD)

  1. B267059
    Disengage the 8 clips and remove the instrument cluster finish panel.

  1. Disconnect the connectors.


16. REMOVE COMBINATION METER ASSEMBLY

  1. B133862
    Remove the 4 screws.

  1. B271477
    Disconnect the 2 connectors and clamp and remove the combination meter.

← REMOVAL (Jul 2007 – Oct 2010)DISASSEMBLY (from Jul 2007) →