DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built Aug 2009 – Oct 2010
Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
| EURO-OBD |
![]() ![]() |
- When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.
- Euro-OBD regulations require that the vehicle's on-board computer illuminates the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:
- The emission control system components.
- The power train control components (which affect vehicle emissions).
- The computer.
- In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
- To check DTCs, connect the intelligent tester or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle.
- The scan tool displays DTCs, the freeze frame data and a variety of engine data.
- The DTCs and freeze frame data can be erased using the scan tool (Click here).
| M-OBD |
![]() ![]() |
- When troubleshooting a Multiplex On-Board Diagnostic (M-OBD) vehicle, the vehicle must be connected to the intelligent tester. Various data output from the ECM can then be read.
- OBD regulations require that the vehicle's on-board computer illuminates the MIL on the instrument panel when the computer detects a malfunction in:
- The emission control system/components.
- The power train control components (which affect vehicle emissions).
- The computer.
- In addition, the applicable DTCs are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
| NORMAL MODE AND CHECK MODE |
| 2-TRIP DETECTION LOGIC |
| FREEZE FRAME DATA |
| DLC3 (Data Link Connector 3) |
| INSPECT BATTERY VOLTAGE |
- Standard Voltage:
- 11 to 14 V
| MIL (Malfunction Indicator Lamp) |
The MIL is illuminated when the ignition switch is first turned ON (the engine is not running).
The MIL should turn off when the engine is started. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.
- HINT:
- If the MIL is not illuminated when the ignition switch is first turned ON, check the MIL circuit (Click here).
| ALL READINESS |
- HINT:
- With "All Readiness" you can check whether or not the DTC judgment has been completed by using the intelligent tester.
- You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.
- With "All Readiness" you can check whether or not the DTC judgment has been completed by using the intelligent tester.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for 30 seconds.
Perform the DTC judgment driving pattern to run the DTC judgment.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTCs to be confirmed.
Check the DTC judgment result.
Result Tester Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- You should perform driving pattern after confirming DTC enabling conditions
UNKNOWN
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit
- DTC judgment completed

