2011-2016 FJ Cruiser · Service Manual ENGINE

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010


EURO-OBD
FI02547E03
  1. When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.
  2. Euro-OBD regulations require that the vehicle's on-board computer illuminates the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:
    1. The emission control system components.
    2. The power train control components (which affect vehicle emissions).
    3. The computer.
  3. In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
  4. To check DTCs, connect the intelligent tester or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle.
  5. The scan tool displays DTCs, the freeze frame data and a variety of engine data.
  6. The DTCs and freeze frame data can be erased using the scan tool (Click here).

M-OBD
FI02547E03
  1. When troubleshooting a Multiplex On-Board Diagnostic (M-OBD) vehicle, the vehicle must be connected to the intelligent tester. Various data output from the ECM can then be read.
  2. OBD regulations require that the vehicle's on-board computer illuminates the MIL on the instrument panel when the computer detects a malfunction in:
    1. The emission control system/components.
    2. The power train control components (which affect vehicle emissions).
    3. The computer.
  3. In addition, the applicable DTCs are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.

NORMAL MODE AND CHECK MODE
The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2-trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1-trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (intelligent tester only).

2-TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent drive cycle, the MIL is illuminated (2nd trip).

FREEZE FRAME DATA
Freeze frame data record the engine condition (fuel system, calculated engine load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

DLC3 (Data Link Connector 3)
Check DLC3 (Click here).

INSPECT BATTERY VOLTAGE
If the voltage is below 11 V, replace the battery before proceeding to the next step.

Standard Voltage:
11 to 14 V


MIL (Malfunction Indicator Lamp)
  1. The MIL is illuminated when the ignition switch is first turned ON (the engine is not running).

  2. The MIL should turn off when the engine is started. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.

    HINT:
    If the MIL is not illuminated when the ignition switch is first turned ON, check the MIL circuit (Click here).


ALL READINESS

HINT:
  1. With "All Readiness" you can check whether or not the DTC judgment has been completed by using the intelligent tester.
  2. You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the tester on.

  4. Clear the DTCs (Click here).

  5. Turn the ignition switch off and wait for 30 seconds.

  6. Perform the DTC judgment driving pattern to run the DTC judgment.

  7. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  8. Input the DTCs to be confirmed.

  9. Check the DTC judgment result.

    Result 
    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. You should perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

← DIAGNOSIS SYSTEM (Aug 2009 – Oct 2010)DTC CHECK / CLEAR (Jul 2007 – Jul 2009) →