2011-2016 FJ Cruiser · Service Manual ENGINE

FAIL-SAFE CHART

System information · Vehicles built from Aug 2014

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Jul 2014 from Aug 2014

If any of the following DTCs are set, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.
DTC
Component
Fail-Safe Operation
Fail-Safe Deactivation Condition
P0011, P0015, P0021, P0025
VVT system
  1. Idle up (Control of combustion worsening)
  2. Stopping fuel-cut control
Pass condition detected
P0031, P0032, P0051, P0052, P101D and P103D
Air fuel ratio sensor heater
ECM turns off air fuel ratio sensor heater.
Ignition switch off
P0037, P0038, P0057, P0058, P102D and P105D
Heated oxygen sensor heater
ECM turns off heated oxygen sensor heater.
Ignition switch off
P0102 and P0103
Mass air flow meter
ECM calculates ignition timing according to engine speed and throttle valve position.
Pass condition detected
P0112 and P0113
Intake air temperature sensor
ECM estimates intake air temperature sensor to be 20°C (68°F).
Pass condition detected
P0115, P0117 and P0118
Engine coolant temperature sensor
ECM estimates engine coolant temperature sensor to be 80°C (176°F).
Pass condition detected
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P2102, P2103, P2111, P2112, P2118, P2119 and P2135
Electronic throttle control system
ECM cuts off throttle actuator current and throttle valve returned to 7° throttle position by return spring.
ECM then adjusts engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with accelerator pedal opening angle, to allow vehicle to continue at minimal speed.*1
Pass condition detected and then ignition switch turned off
P0300, P0301, P0302, P0303, P0304, P0305 and P0306
*2
  1. Fuel injector
  2. Electronic throttle control system
When catalyst damage misfire occurs (MIL blinking), following fail-safe operation performed for catalyst overheat malfunction prevention
  1. Under low load and low engine speed
    1. Fuel cut performed on malfunctioning cylinder
  2. Under high load and high engine speed
    1. Throttle valve opening angle control is performed
    2. All cylinder fuel cut or malfunction cylinder fuel cut
Pass condition detected and then ignition switch turned off
P0327, P0328, P0332 and P0333
Knock sensor
ECM sets ignition timing to maximum retard.
Ignition switch off
P0351 to P0356
Ignition coil assembly
ECM cuts fuel.
Pass condition detected
P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138
Accelerator pedal position sensor
The accelerator pedal position sensor has 2 sensor circuits: Main and Sub.
If either circuit malfunctions, ECM limits the engine output.
If both circuits malfunction, ECM regards accelerator pedal as being released. As a result, throttle valve is closed and engine idles.
Pass condition detected and then ignition switch turned off
P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 and P2256
Air fuel ratio sensor
  1. Air fuel ratio feedback control is stopped.
  2. Current to the air fuel ratio sensor heater is cut.
Pass condition detected and then ignition switch turned off
P2432, P2433, P2437, P2438, P2440, P2442 and P2445
Secondary air injection system
Throttle valve opening angle control is performed.
Pass condition detected

HINT:
  1. *1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.
  2. *2: Misfire related fail-safe operations occur when catalyst overheat malfunctions occur.

← FAIL-SAFE CHART (Aug 2009 – Jul 2014)DATA LIST / ACTIVE TEST (Jul 2007 – Nov 2007) →