2011-2016 FJ Cruiser · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built Jul 2007 – Nov 2007

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014


DATA LIST

HINT:
By reading the Data List displayed on an intelligent tester, values can be checked, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step in troubleshooting is one method to shorten diagnostic time.

NOTICE:
In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the tester ON.

  6. Select the following menu items: Powertrain / Engine and ECT / Data List.

  7. Check the values by referring to the table below.

    HINT:
    If no idling conditions are specified, the transmission gear should be in the neutral position (P or N), and the A/C switch and all accessory switches should be OFF.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Injector (Port)
    Injection period of No. 1 cylinder:
    Min.: 0 ms, Max.: 32.64 ms
    1.6 to 2.7 ms: Idling
    -
    IGN Advance
    Ignition timing advance for No. 1 cylinder:
    Min.: -64 deg., Max.: 63.5 deg.
    BTDC 7 to 24°: Idling
    -
    Calculate Load
    Calculated load by ECM:
    Min.: 0 %, Max.: 100 %
    1. 10 to 40 %: Idling
    2. 10 to 40 %: Running without load (2500 rpm)
    -
    MAF
    Air flow rate from MAF meter:
    Min.: 0 g/sec, Max.: 655.35 g/sec
    3.2 to 4.7 g/sec: Idling
    13.1 to 18.9 g/sec: 2500 rpm
    If value approximately 0.0 g/sec:
    1. Mass air flow meter power source circuit open
    2. VG circuit open or short
      If value 160.0 g/sec or more:
    3. E2G circuit open
    Engine Speed
    Engine speed:
    Min.: 0 rpm, Max.: 16383.75 rpm
    650 to 750 rpm: Idling
    -
    Vehicle Speed
    Vehicle speed:
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer
    Coolant Temp
    Engine coolant temperature:
    Min.: -40°C, Max.: 140°C
    80 to 100°C
    (176 to 212°F):After warming up
    1. If value -40°C (-40°F): sensor circuit open
    2. If value 140°C (284°F) or more: sensor circuit shorted
    Intake Air
    Intake air temperature:
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    1. If value -40°C (-40°F): sensor circuit open
    2. If value 140°C (284°F) or more: sensor circuit shorted
    Air-Fuel Ratio
    Ratio compared to stoichiometric level:
    Min.: 0, Max.: 1.999
    0.8 to 1.2: During idling
    -
    Purge Density Learn Value
    Learning value of purge density:
    Min.: -50 , Max.: 350
    -40 to 0 %: Idling
    Service data
    Evap Purge Flow
    Ratio of evaporative purge flow to intake air volume:
    Min.: 0 %, Max.: 102.4 %
    0 to 100 %: Idling
    -
    EVAP (Purge) VSV
    EVAP (Purge) VSV control duty:
    Min.: 0 %, Max.: 100 %
    0 to 100 %: During idling
    Order signal from ECM
    Knock Correct Learn Value
    Correction learning value of knocking:
    Min.: -64° CA, Max.: 1984° CA
    0 to 22 °CA:
    Driving, 70 km/h (44 mph)
    Service data
    Knock Feedback Value
    Feedback value of knocking:
    Min.: -64° CA, Max.: 1984° CA
    -22 to 0 °CA
    Driving, 70 km/h (44 mph)
    Service data
    Clutch Current
    Throttle actuator clutch current:
    Min.: 0 A, Max.: 2.49 A
    -
    Service data
    Accelerator Position No.1
    Absolute Accelerator Pedal Position (APP) No. 1:
    Min.: 0 %, Max.: 100 %
    10 to 22 %: Accelerator pedal released
    54 to 86 %: Accelerator pedal fully depressed
    -
    Accelerator Position No.2
    Absolute APP No. 2:
    Min.: 0 %, Max.: 100 %
    12 to 42 %: Accelerator pedal released
    66 to 98 %: Accelerator pedal fully depressed
    -
    Accelerator Position No.1
    APP sensor No. 1 voltage:
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS service data
    Accelerator Position No.2
    APP sensor No. 2 voltage:
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS service data
    Accelerator Position No.1
    APP sensor No. 1 voltage:
    Min.: 0 V, Max.: 5 V
    0.5 to 1.1 V: Accelerator pedal released.
    2.6 to 4.5t V: Accelerator pedal fully depressed.
    -
    Accelerator Position No.2
    APP sensor No. 2 voltage:
    Min.: 0 V, Max.: 5 V
    1.2 to 2.0 V: Accelerator pedal released.
    3.4 to 5.0 V: Accelerator pedal fully depressed.
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle:
    ON or OFF
    ON: Idling
    -
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value):
    Min.: 0 V, Max.: 5 V
    0.4 to 0.8 V
    -
    Accel Fully Close #1 (AD)
    Accelerator fully closed value No.1 (AD):
    Min.: 0, Max.: 4.9804 V
    -
    ETCS service data
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No.1:
    Min.: 0, Max.: 124.512 deg
    -
    ETCS service data
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No.2:
    Min.: 0, Max.: 124.512 deg
    -
    ETCS service data
    Fail Safe Drive
    Whether or not fail-safe function executed:
    ON or OFF
    ON: ETCS has failed
    -
    Fail Safe Drive (Main CPU)
    Whether or not fail-safe function executed:
    ON or OFF
    ON: ETCS has failed
    -
    ST1
    Brake pedal signal:
    ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard:
    ON or OFF
    -
    ETCS service data
    Open Side Malfunction
    Throttle valve open side malfunction:
    ON or OFF
    -
    ETCS service data
    Throttle Position
    Absolute throttle position sensor:
    Min.: 0 %, Max.: 100 %
    1. 10 to 24 %: Throttle fully closed
    2. 40 to 98 %: Throttle fully open
    Read value with intrusive operation (active test)
    Throttle Idle Position
    Whether or not throttle position sensor detecting idle:
    ON or OFF
    ON: Idling
    -
    Throttle Require Position
    Throttle requirement position:
    Min.: 0 V, Max.: 5 V
    0.5 to 1.0 V: Idling
    -
    Throttle Sensor Position
    Throttle sensor positioning:
    Min.: 0 %, Max.: 100 %
    0 to 10%: Throttle fully closed
    50 to 80%: Throttle fully open
    Recognition value for throttle opening angle on ECM
    Read value with ignition switch ON
    Throttle Sensor Position #2
    Throttle sensor positioning #2:
    Min.: 0 %, Max.: 100 %
    42 to 62%: Throttle fully closed
    92 to 100%: Throttle fully open
    Recognition value for throttle opening angle on ECM
    Read value with ignition switch ON
    Throttle Position No.1
    Throttle position No. 1:
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS service data
    Throttle Position No.2
    Throttle position No. 2:
    Min.: 0 V, Max.: 4.95 V
    -
    ETCS service data
    Throttle Position No.1
    Throttle position No. 1:
    Min.: 0 V, Max.: 5 V
    1. 0.5 to 1.2 V: Throttle fully closed
    2. 3.2 to 4.8 V: Throttle fully opened
    -
    Throttle Position No.2
    Throttle position No. 2:
    Min.: 0 V, Max.: 5 V
    1. 2.0 to 2.9 V: Throttle fully closed
    2. 4.6 to 5.0 V: Throttle fully open
    -
    Throttle Position Command
    Throttle position command value:
    Min.: 0 V, Max.: 4.98 V
    0.5 to 4.8 V
    ETCS service data
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1:
    Min.: 0 V, Max.: 4.9804 V
    0.6 to 1.0 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2:
    Min.: 0 V, Max.: 4.9804 V
    2.0 to 2.6 V
    ETCS service data
    Throttle Sens Open #1(AD)
    Throttle sensor opener position No.1 (AD):
    Min.: 0 V, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Motor
    Whether or not throttle motor control permitted:
    ON or OFF
    ON: Idling
    Read value with ignition switch ON (Do not start engine)
    Throttle Motor Current
    Throttle motor current:
    Min.: 0 A, Max.: 20 A
    0 to 3.0 A: Idling
    -
    Throttle Motor
    Throttle motor:
    Min.: 0 %, Max.: 100 %
    0.5 to 40 %: Idling
    -
    Throttle Motor Current
    Throttle motor current:
    Min.: 0 A, Max.: 19.92 A
    -
    -
    Throttle Motor Open Duty
    Throttle actuator opening duty ratio:
    Min.: 0 %, Max.: 100 %
    -
    ETCS service data
    Throttle Motor Close Duty
    Throttle actuator closed duty ratio:
    Min.: 0 %, Max.: 100 %
    -
    ETCS service data
    Throttle Motor Duty (Open)
    Throttle motor duty ratio (open):
    Min.: 0 %, Max.: 100 %
    -
    When accelerator pedal depressed, duty ratio increased
    Throttle Motor Duty (Close)
    Throttle motor duty ratio (close):
    Min.: 0 %, Max.: 100 %
    -
    When accelerator pedal released quickly, duty ratio increased
    O2S B1 S2
    Heated oxygen sensor output voltage for bank 1 sensor 2:
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving, 70 km/h (44 mph)
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
    O2S B2 S2
    Heated oxygen sensor output voltage for bank 2 sensor 2:
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving, 70 km/h (44 mph)
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
    AFS B1 S1
    A/F sensor output voltage for bank 1 sensor 1:
    Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
    AFS B2 S1
    A/F sensor output voltage for bank 2 sensor 1:
    Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
    AFS B2 S1
    A/F sensor output current for bank 2 sensor 1:
    Min.: -128 mA, Max.: 127.99 mA
    -
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output current of sensor
    Short FT #1
    Short-term fuel trim of bank 1:
    Min.: -100 %, Max.: 99.2%
    0 +/- 20 %
    Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
    Long FT #1
    Long-term fuel trim of bank 1:
    Min.: -100 %, Max.: 99.2 %
    0 +/- 20 %
    Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
    Short FT #2
    Short-term fuel trim of bank 2:
    Min.: -100 %, Max.: 99.2%
    0 +/- 20 %
    Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
    Long FT #2
    Long-term fuel trim of bank 2:
    Min.: -100 %, Max.: 99.2 %
    0 +/- 20 %
    Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
    Fuel System Status (Bank1)
    Fuel system status (Bank 1):
    OL or CL or OL DRIVE or OL FAULT or CL FAULT
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
    3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
    4. OL FAULT: Open loop due to detected system fault
    5. CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning
    Fuel System Status (Bank2)
    Fuel system status (Bank 2):
    OL or CL or OL DRIVE or OL FAULT or CL FAULT
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.
    3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
    4. OL FAULT: Open loop due to detected system fault
    5. CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning
    AF FT B1 S1
    Short-term fuel trim associated with bank 1 sensor 1:
    Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio=1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AFS B1 S1
    A/F sensor output current for bank 1 sensor 1:
    Min.: -128 mA, Max.: 127.99 mA
    -
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output current of sensor
    AF FT B2 S1
    Short-term fuel trim associated with bank 2 sensor 1:
    Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = Lean
    2. Stoichiometric air fuel ratio=1
    3. Value greater than 1 (1.001 to 1.999) = RICH
    -
    Initial Engine Coolant Temp
    Initial engine coolant temperature:
    Min.: -40°C, Max.: 120°C
    Coolant temperature when engine started
    Service data
    Initial Intake Air Temp
    Initial intake air temperature:
    Min.: -40°C, Max.: 120°C
    Intake air temperature when engine started
    Service data
    Injection Volum (Cylinder1)
    Injection volume (cylinder 1):
    Min.: 0 ml, Max.: 2.048 ml
    0 to 0.5 ml
    Quantity of fuel injection volume for 10 times
    Starter Signal
    Starter signal:
    ON or OFF
    ON: Cranking
    -
    Power Steering Switch
    Power steering signal:
    ON or OFF
    ON: Power steering operation
    -
    Power Steering Signal
    Power steering signal (history):
    ON or OFF
    ON: When steering wheel first turned after battery terminals connected
    This signal status usually ON until battery terminals disconnected
    Closed Throttle Position SW
    Closed throttle position switch:
    ON or OFF
    ON: Throttle fully closed
    OFF: Throttle open
    -
    A/C Signal
    A/C signal:
    ON or OFF
    ON: A/C ON
    -
    Neutral Position SW Signal
    PNP switch status (for A/T models):
    ON or OFF
    ON: P or N position
    -
    Electrical Load Signal
    Electrical load signal:
    ON or OFF
    ON: Headlights or defogger turned ON
    -
    Stop Light Switch
    Stop light switch:
    ON or OFF
    ON: brake pedal depressed
    -
    ETCS Actuator Power
    Whether or not electric throttle control system power inputted:
    ON or OFF
    ON: Ignition switch ON and system normal
    -
    +BM Voltage
    +BM voltage:
    Min.: 0, Max.: 19.92182
    11 to 14 (V): Ignition switch ON and system normal
    ETCS service data
    Battery Voltage
    Battery voltage:
    Min.: 0 V, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Actuator Power Supply
    Actuator power supply:
    ON or OFF
    ON: Idling
    ETCS service data
    Atmosphere Pressure
    Atmospheric pressure:
    Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure (absolute pressure)
    -
    Fuel Pump Speed Control
    Fuel pump speed control status:
    ON/H or OFF/L
    ON: Idling (or under very light load)
    -
    ACIS VSV
    ACIS VSV:
    ON or OFF
    -
    ON: Open
    OFF: Closed
    ACT VSV
    A/C cut status for Active Test:
    ON or OFF
    -
    Active Test support data
    VVT Control Status (Bank2)
    VVT control (bank 2) status:
    ON or OFF
    -
    Active Test support data
    EVAP Purge VSV
    VSV status for EVAP control:
    ON or OFF
    -
    Active Test support data
    Fuel Pump/Speed Status
    Fuel pump/status:
    ON or OFF
    ON: Engine running
    Active Test support data
    VVT Control Status (Bank1)
    VVT control (bank 1) status:
    ON or OFF
    -
    Active Test support data
    TC and TE1
    TC and CG (TE1) terminal of DLC3:
    ON or OFF
    -
    -
    Engine Speed of Cyl #1
    Engine RPM for cylinder 1:
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when [Check the Cylinder Compression] performed using Active Test
    51199 rpm: Not performed Active Test
    Engine Speed of Cyl #2
    Engine RPM for cylinder 2:
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when [Check the Cylinder Compression] performed using Active Test
    51199 rpm: Not performed Active Test
    Engine Speed of Cyl #3
    Engine RPM for cylinder 3:
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when [Check the Cylinder Compression] performed using Active Test
    51199 rpm: Not performed Active Test
    Engine Speed of Cyl #4
    Engine RPM for cylinder 4:
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when [Check the Cylinder Compression] performed using Active Test
    51199 rpm: Not performed Active Test
    Engine Speed of Cyl #5
    Engine RPM for cylinder 5:
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when [Check the Cylinder Compression] performed using Active Test
    51199 rpm: Not performed Active Test
    Engine Speed of Cyl #6
    Engine RPM for cylinder 6:
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when [Check the Cylinder Compression] performed using Active Test
    51199 rpm: Not performed Active Test
    Av Engine Speed of All Cyl
    Engine RPM for all cylinders:
    Min.: 0 rpm, Max.: 25600 rpm
    -
    Output only when [Check the Cylinder Compression] performed using Active Test
    51199 rpm: Not performed Active Test
    VVT Aim Angle (Bank1)
    *1
    VVT aim angle (bank 1):
    Min.: 0 %, Max.: 100 %
    0 to 100 %
    VVT duty signal value during intrusive operation
    VVT Change Angle (Bank1)
    *1
    VVT change angle:
    Min.: 0°FR, Max.: 60°FR
    0 to 56 °FR
    Displacement angle during intrusive operation
    VVT OCV Duty (Bank1)
    *1
    VVT OCV operation duty:
    Min.: 0 %, Max.: 100 %
    0 to 100 %
    Requested duty value for intrusive operation
    VVT Aim Angle (Bank2)
    *1
    VVT aim angle (bank 2):
    Min.: 0 %, Max.: 100 %
    0 to 100 %
    VVT duty signal value during intrusive operation
    VVT Change Angle (Bank2)
    *1
    VVT change angle (bank 2):
    Min.: 0°FR, Max.: 60°FR
    0 to 56 °FR
    Displacement angle during intrusive operation
    VVT OCV Duty (Bank2)
    *1
    VVT OCV (bank 2) operation duty:
    Min.: 0 %, Max.: 100 %
    0 to 100 %
    Requested duty value for intrusive operation
    Idle Fuel Cut
    Fuel cut idle:
    ON or OFF
    ON: Fuel cut operation
    FC IDL = "ON" when throttle valve fully closed and engine speed over 3,500 rpm
    FC TAU
    Fuel cut TAU: Fuel cut during very light load:
    ON or OFF
    ON: Fuel cut operating
    Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
    # Codes
    Number of detected DTCs:
    Min.: 0, Max.: 255
    0: No DTC detected
    -
    Check Mode
    Check mode:
    ON or OFF
    ON: Check mode ON
    Click here
    SPD Test
    Check mode result for vehicle speed sensor:
    COMPL or INCMPL
    -
    -
    OXS2 Test
    Check mode result for HO2 sensor (bank 2) :
    COMPL or INCMPL
    -
    -
    OXS1 Test
    Check mode result for HO2 sensor (bank 1) :
    COMPL or INCMPL
    -
    -
    A/F Test Results (Bank2)
    Check mode result for air fuel ratio sensor (bank 2) :
    COMPL or INCMPL
    -
    -
    A/F Test Results (Bank1)
    Check mode result for air fuel ratio sensor (bank 1) :
    COMPL or INCMPL
    -
    -
    MIL
    MIL status:
    ON or OFF
    ON: MIL ON
    -
    MIL ON Run Distance
    Distance traveled since MIL turned ON:
    Min.: 0 km,
    Max.: 65535 km
    Drive distance after DTC detected
    -
    Running Time from MIL ON
    Running time since MIL turned ON:
    Min.: 0 min.,
    Max.: 65535 min.
    Equivalent to running time after MIL ON
    -
    Engine Run Time
    Engine run time:
    Min.: 0 s.,
    Max.: 65535 s.
    Time after engine start
    Service data
    Time after DTC Cleared
    Time after DTC cleared:
    Min.: 0 min.,
    Max.: 65535 min.
    Equivalent to time after DTCs erased
    -
    Distance from DTC Cleared
    Distance after DTC cleared:
    Min.: 0 km,
    Max.: 65535 km
    Equivalent to drive distance after DTCs erased
    -
    Warmup Cycle Cleard DTC
    Number of warm-up cycles after DTC cleared:
    Min.: 0, Max.: 255
    -
    -
    OBD Requirements
    OBD requirement
    OBD2
    -
    Number of Emission DTC
    Number of emission related DTCs
    0: No emission related DTC detected
    -
    Complete Parts Monitor
    Comprehensive component monitor:
    NOT AVL or AVAIL
    -
    -
    Fuel System Monitor
    Fuel system monitor:
    NOT AVL or AVAIL
    -
    -
    Misfire Monitor
    Misfire monitor:
    NOT AVL or AVAIL
    -
    -
    Model Code
    Identifying model code
    GSJ1##
    -
    Engine Type
    Identifying engine type
    1GRFE
    -
    Cylinder Number
    Identifying cylinder number:
    Min.: 0, Max.: 255
    6
    -
    Transmission Type
    Identifying transmission type:
    MT or 5AT
    MT: Manual transmission
    ECT (5th): Automatic transmission
    -
    Destination
    Identifying destination
    A (America)
    -
    Model Year
    Identifying model year:
    Min.: 1900, Max.: 2155
    200#
    -
    System Identification
    Identifying engine system
    Gasoline
    -
    *1: DATA LIST values are only displayed when performing the following ACTIVE TESTs: VVT B1 or VVT B2. For other ACTIVE TESTs, the DATA LIST value will be 0.


ACTIVE TEST

HINT:
Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve) and actuators, to be operated without removing any parts. The Active Test can be performed with the intelligent tester. Performing the Active Test as the first step in troubleshooting is one method to shorten diagnostic time.

  1. Data List can be displayed during Active Test.
  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the tester ON.

  4. Select the following menu items: Powertrain / Engine and ECT / Active Test.

  5. Perform the Active Tests by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Notes
    Control the Injection Volume
    Change injection volume
    Between -12.5 % and 24.8 %
    1. All injectors tested at same time
    2. Perform test at less than 3000 rpm
    3. Injection volume can be changed in 0.1 % graduations within control range
    Control the Injection Volume for A/F Sensor
    Change injection volume
    Lower by 12.5 % or increase by 25 %
    1. Perform test at less than 3,000 rpm
    2. Control the Injection Volume for A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs
    3. To conduct test, select following menu items: Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F Control System / AFS B1S1 and O2S B1S2
    Activate the Fuel Pump Speed Control
    Fuel pump speed control
    ON (low speed)/ OFF (high speed)
    -
    Activate the VSV for Intake Control
    ACIS VSV
    ON/OFF
    -
    Activate the VSV for Evap Control
    Activate EVAP VSV control
    ON/OFF
    -
    Control the A/C Cut Signal
    Control A/C cut signal
    ON/OFF
    -
    Control the Fuel Pump / Speed
    Activate fuel pump (C/OPN Relay)
    ON/OFF
    -
    Connect the TC and TE1
    Turn on and off TC and CG (TE1) connection
    ON/OFF
    1. ON: TC and CG (TE1) connected
    2. OFF: TC and CG (TE1) disconnected
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Control the ETCS Open/Close Slow Speed
    Throttle motor
    ON: throttle valve opens/closes slowly
    Test possible when following conditions met:
    1. Ignition switch ON
    2. Engine does not start
    3. Fully depressing accelerator pedal (APP: 58 degrees or more)
    Control the ETCS Open/Close Fast Speed
    Throttle motor
    ON: throttle valve opens/closes fast
    Control the VVT Linear (Bank1)
    Control the VVT (bank 1)
    -128 to 127 %
    This value added to present OCV control duty
    100 %: Maximum advance
    -100 % : Maximum retard
    1. Engine stall or rough idle when VVT actuator operated by 100 %
    2. Test possible during engine idling
    Control the VVT System (Bank1)
    Turn on and off OCV
    (Oil Control Valve)
    ON/OFF
    1. Engine stalls or idles roughly when OCV turned ON
    2. Normal engine running or idling when OCV off
    Control the VVT Linear (Bank2)
    Control the VVT (bank 2)
    -128 to 127 %
    This value added to present OCV control duty
    100 %: Maximum advance
    -100 % : Maximum retard
    1. Engine stall or rough idle when VVT actuator operated by 100 %
    2. Test possible during engine idling
    Control the VVT System (Bank2)
    Turn on and off OCV
    (Oil Control Valve)
    ON/OFF
    1. Engine stalls or idles roughly when OCV turned ON
    2. Normal engine running or idling when OCV off
    Control the Cylinder#1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    Test possible during vehicle stopping and engine idling
    Control the Cylinder#2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    Control the Cylinder#3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    Control the Cylinder#4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    Control the Cylinder#5 Fuel Cut
    Cylinder #5 injector fuel cut
    ON/OFF
    Control the Cylinder#6 Fuel Cut
    Cylinder #6 injector fuel cut
    ON/OFF
    Control the All Cylinders Fuel Cut
    All cylinder injectors fuel cut
    ON/OFF
    Check the Cylinder Compression
    All cylinder injectors fuel cut and ignition stop
    ON/OFF
    *

    HINT:
    *: When performing the Active Test item "Check the Cylinder Compression" and then cranking the engine, the ECM stops the fuel injection and ignition, and measures the engine speed for each cylinder.
    If one cylinder's speed is higher than the others, that cylinder's compression pressure can be concluded to be lower than the others.

    1. Warm up the engine.
    2. Turn the ignition switch OFF.
    3. Connect the intelligent tester to the DLC3.
    4. Turn the ignition switch ON.
    5. Turn the tester ON.
    6. Select the following menu items: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.
    7. Select the following monitor items: Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl.
    8. Press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.

      HINT:
      Fuel injection and ignition for all cylinders is prohibited at this time, and each cylinder's engine speed measurement will enter standby mode.

    9. Crank the engine until the monitor item values "Engine speed of Cyl #1 to #6" and "Av Engine Speed of All Cyl" change.
    10. Monitor the engine speed (Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl) displayed on the tester.

      HINT:
      The tester displays the values to be extremely high before cranking the engine. Each cylinder's engine speed is measured while cranking the engine and then the tester displays the actual engine speed values.

      NOTICE:
      1. The Active Test item "Check the Cylinder Compression" will automatically turn OFF 255 seconds after the Active Test is turned on.
      2. When the "Check the Cylinder Compression" is OFF and the engine is cranked, the engine will start.
      3. If the "Check the Cylinder Compression" test needs to be performed again after each cylinder's engine speed measurement has been performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.
      4. Use a fully-charged battery.

← FAIL-SAFE CHART (from Aug 2014)DATA LIST / ACTIVE TEST (Dec 2007 – Jul 2009) →